水冷爐條 的英文怎麼說
中文拼音 [shuǐlěnglútiáo]
水冷爐條
英文
water bar-
According to fuel and and operation condition in chongqing iron and steel group corporation, many kinds of advanced technologies are adopted, such as closed loop soft water circulation cooling, copper cooling stave, bell - less top with central charging hopper, carbon bricks combined furnace bottom with ceramic cup, russia top burner type hot air stove, duplex preheating of hot air stove, and nut coke charging
摘要根據重鋼高爐的原燃料條件和操作條件，設計了重鋼四高爐擴容性易地大修工程，採用了全軟水密閉循環冷卻、銅冷卻壁、串罐式無料鐘爐頂、炭磚陶瓷杯復合爐缸、俄羅斯「卡魯金」頂燃式熱風爐、熱風爐雙預熱、焦丁入爐等先進技術。The degrees of crystallinity of pure ptfe under the different conditions of water cooling, air cooling and furnace - varying cooling were made comparison by xrd. the thermal stability of pure ptfe and solid lubricant was analyzed by dsc - tg ; the composition and valence state of elements in the surface of carbon fiber, solid lubricant before and after friction test and lubricant transfer film were characterized by xps ; the frictional property of solid lubricant was tested by pin and disk test rig. the frictional wear property of solid lubricant between embedded bearing sleeve and steel axle friction pair ring was tested by special simulate test machine, the hardness of solid lubricant was tested by pm ; the compression strength of solid lubricant was tested by material test machine
用sem表徵原料微觀結構、摩擦表面及潤滑轉移膜表面形貌：用xrd進行原料物相分析，及比較水冷卻、空氣冷卻、隨爐冷卻三種工藝條件下的純聚四氟乙烯樹脂的結晶度；用dsc - tg分析純聚四氟乙烯樹脂及固體潤滑劑的熱穩定性；用xps表徵碳纖維表面、固體潤滑劑摩擦前後表面、潤滑轉移膜表面的元素組成、價態變化；用銷盤式摩擦磨損試驗機對固體潤滑劑進行摩擦性能測試；採用專用的臺架模擬試驗機對固體潤滑劑鑲嵌軸承套與鋼軸摩擦副間的摩擦磨損性能進行測定；用萊次偏光顯微鏡（ pm ）測試固體潤滑劑的硬度；用材料試驗機測試固體潤滑劑的抗壓強度等。Compared with other general cfd software, the numerical modeling software of combustion process improved by the author of this paper has following features : ( 1 ) it can adjust the corresponding parameters and manipulating methods according to furnace architecture, operational parameters and fuels etc. ; ( 2 ) it can arrange the nodes of grid flexibly and also make special calculation to certain nodes, which cannot be accomplished by the general commercial software ; ( 3 ) in the boundary ( water - cooled wall ) condition processing, the third boundary condition is selected for the temperature calculating, linking the combustion process inside the furnace with the flow and heat exchange of water inside the water - cooled wall, so the heat absorbing and the influence of the water - cooled wall to combustion process and heat transfer of furnace are explicitly explained
與其它通用的cfd軟體相比，經論文作者所改進的燃燒過程數值模擬軟體的特點在於： （ 1 ）能夠結合爐子結構、運行參數及燃料等，調整模型中相應的參數及處理方法； （ 2 ）可以靈活的安排網格節點，對某些節點進行特殊處理； （ 3 ）在邊界（水冷壁）條件的處理上，溫度選用了第三類邊界條件，把爐內燃燒過程和水冷壁內工質的流動和換熱聯系了起來，使得水冷壁內的吸熱情況對爐內的燃燒和結渣的影響充分體現出來。But the paper set out form the lab, the conditions of the temperature of the water wall tubes and the ambience of the furnace is imitated in lab, the material of sample is adopted by the steel of the water wall tubes of the boiler, which made the test conditions approach to the fact work conditions of the water wall tubes of the boiler and made the imitation accurate
本文則從實驗室出發，在實驗室模仿鍋爐水冷壁的溫度條件和爐膛氣氛條件，採用鍋爐水冷壁用鋼（ 20g ）作為試樣材質，盡可能接近鍋爐水冷壁的實際工作條件以達到模仿的效果。分享友人