油冷卻試驗 的英文怎麼說

中文拼音 [yóulěngquèshìyàn]
油冷卻試驗 英文
oil cold test
  • 油 : Ⅰ名詞1 （脂肪; 油脂） oil; fat; grease 2 （姓氏） a surname Ⅱ動詞1 （用桐油、油漆等塗抹） apply t...
  • 冷 : Ⅰ形容詞1 （溫度低; 感覺溫度低） cold:冷水 coldwater; 你冷不冷? do you feel cold?; are you feeling...
  • 卻 : Ⅰ動詞1 （後退） step back 2 （使退卻） drive back; repulse 3 （推辭; 拒絕） decline; refuse; reje...
  • 試 : 名詞（古代占卜用的器具） astrolabe
  • 驗 : 動詞1. （察看; 查考） examine; check; test 2. （產生預期的效果） prove effective; produce the expected result
  • 試驗 : trial; experiment; test
  1. The calculation method using in factory has larger error and is n ' t used in high ignition point oil transformer. in this paper a calculation method, which has been verified by experiment results, is presented based on the fundamental theories and rule equation of heat transfer to calculate the temperature rise of average oil, top oil, coil, core and hot - point. a program has been compiled

    本課題立足於工程實際應用，根據傳熱學基本原理和經典試驗換熱準則式，通過對變壓器發熱冷卻原理進行分析和研究，提出了一套計算變壓器平均油溫升、頂油溫升、繞組溫升、鐵芯溫升和最熱點溫升的計算方法並編制了計算軟體，對影響變壓器溫升的因素進行了分析。
  2. Standard test method for determination of cooling characteristics of quench oils by cooling curve analysis

    通過冷卻曲線分析測定淬火油冷卻特性的標準試驗方法
  3. Methods of test for petroleum and its products - industrial quenching oils - determination of cooling characteristics - nickel - alloy probe test method

    石油和石油產品試驗方法.第414部分;工業淬火油.冷卻特性測定.鎳合金探頭試驗法
  4. The experiments of high speed milling of titanium alloy were conducted under different cooling and lubricating modes, i. e. dry milling, flood coolant, oil mist with nitrogen gas, cryogenic nitrogen gas jet, and cryogenic nitrogen gas jet with minimal quantities of lubricant

    在干銑削、澆注切削液、常溫氮氣油霧、低溫氮氣射流和低溫氮氣射流結合微量潤滑等冷卻潤滑條件下進行了鈦合金的高速銑削對比試驗。
  5. Test method of charge air coolers for marine diesel engines

    船用柴油機空氣冷卻器試驗方法
  6. Whole scheme of frame design of test - bed is proposed as : the host fanner supply the firebox the once and twice air required by diesel oil ' s burning and the cooling air ; the export parameter of the test - bed is varied by the adjust of the flux of air and diesel oil. and the air flux is varied by adjusting the rev of the fanner adjusted by transducer and the corner of the fan inlet adjusted by step motor. the quantity of oil is varied by adjusting the oil valve adjusted by step motor ; the measurement of the air flux in the test - bed adopts the method of fanner dynamics performance test in the nation criterion

    確立了實驗臺結構設計方案：主風機為燃燒器提供燃燒所需的一次、二次進風量及冷卻風量；利用變頻器調節主風機轉速、用步進電機調節風門開度來調節風量，用步進電機調節回油閥開度來調節供油量，從而實現對模擬實驗臺出口煙氣熱流量的調節；實驗臺的流量測量採用風機動力性能測試標準中測流量方法等。
  7. Whole scheme of frame design of testing flat is proposed as : the host fanner supply the air required by flamer ’ s burning and cooling, the export parameter of the flat varies by different rotate speed of the fanner 、 angle of the fan inlet and the quantity of oil, the measurement of flow in the testing flat adopts the method of fanner dynamics performance test in the nation criterion

    確立了實驗臺結構設計方案：主風機為燃燒器提供燃燒所需的一次、二次進風量及冷卻風量；模擬實驗臺出口煙氣熱流量是通過調節風機的轉速、風門開度及燃油量來改變；實驗臺的流量測量採用風機動力性能測試標準中流量方法等。
  8. Application testing of oil - to - air oil coolers for cooling performance

    油空氣式潤滑油冷卻器的冷卻性能應用試驗
  9. Test method for cold filter plugging point of diesel and heating fuels

    柴油和加熱燃料冷卻過濾堵塞點的試驗方法
  10. Stand test methods of diesel locomotives - test of oil water cooling equipment performance and heat balance

    內燃機車臺架試驗方法油水冷卻裝置性能及熱平衡試驗
  11. Therefore, it is necessary for us to conduct a series of principle analysis on different sections of the station such as the fuel system, lube system and cooling system of the diesel engine for generators, and the shaft generator as well as the main switchboard etc. it is also important to carry out at meantime a number of reliability tests and analyze the test results so as to assure all the units of the station will run smoothly

    因此，我們通過對船舶電站中柴油機的供油系統、潤滑系統、冷卻系統、軸帶發電機、主配電板等各個環節從原理上進行分析，並進行必要的可靠性試驗，對試驗數據進行分析，確保船舶電站各個環節的運行良好。
分享友人
分享到 Line

分享到臉書