油管的布置 的英文怎麼說

中文拼音 [yóuguǎndebùzhì]
油管的布置 英文
oil piping layout
  • 油 : Ⅰ名詞1 （脂肪; 油脂） oil; fat; grease 2 （姓氏） a surname Ⅱ動詞1 （用桐油、油漆等塗抹） apply t...
  • 管 : Ⅰ名詞1 （管子） pipe; tube 2 （吹奏的樂器） wind musical instrument 3 （形狀似管的電器件） valve;...
  • 的 : 4次方是 The fourth power of 2 is direction
  • 置 : 動詞1. （擱; 放） place; put; lay 2. （設立; 布置） set up; establish; arrange; fix up 3. （購置） buy; purchase
  • 油管 : [石油工業]1. （輸油管道） oil pipe 2. （井架用的油管） oil tube
  1. For solving all these problems, through applying visualization technology of engineer design to the design of oil - feed unit, this paper constructs the entity model of oil - feed unit, establish the three - dimensional standard parts, implement the semi - automated and automated connect, and produce automatically the 2d or 3d part drawings. using this system the designer can observe and evaluate the space model of the unit, discuss the feasibility of space layout and the probable errors, so that the decision can be optimized and the competition of enterprise can be improved greatly

    針對船舶供油單元設計、製造中的上述問題，本系統擬將工程設計可視化技術應用於船舶供油單元的設計，構造船舶供油單元的三維實體模型，建立三維標準件庫，實現管路的自動、半自動連接，自動生成管路的二維和三維零件圖，使得設計人員在設計階段就可觀察、評判單元的空間模型，直觀地探討空間布置的合理性和存在的問題，從而幫助決策的優化，提高企業競爭力。
  2. This article aims at the boiler ' s problems in operation : 1 ) under nominal load, the smoke temperature at the outlet of hearth reaches 1200, far more exceeds 1050 the original designed temperature. this will always result in slag inside boiler and the temperature of overheater ' s pipe superheat, so that boiler cannot take nominal load and all these influence boiler ' s nomal operation heavily, 2 ) this article also studied the reason why the assistant oil becoming necessary when coal changes. during the nomal operation, many factors ( makeup of combustor and its disposal, smirch and encrust of water wall, excessive air coefficient, temperature of primary air, coal type and density of coal dust ) can deviate the designed working conditions, then affect the boiler ' s nomal operation

    本文針對該鍋爐在實際運行中存在的問題：在額定負荷下，爐膛出口超溫、低溫段過熱器前煙溫高達936 ，遠遠超過815的設計值；噴燃器四周水冷壁結焦嚴重，過熱器管壁溫度超標，無法帶上額定負荷；甚至有時因燃煤質量的變化，必須投油助燃的嚴重情況進行了分析研究。在實際生產過程中，燃燒器的結構、布置，水冷壁的粘污、結垢，過剩空氣系數、一次風溫、煤種及其濃度變化等許多因素都會偏離鍋爐的設計工況，從而影響爐內的傳熱和燃燒，造成爐膛出口超溫、水冷壁結渣等問題。
  3. It is reviewed 6 kinds of essential problem, ie. function is insufficient, space planning is inappropriate, pipe distributed is disorder, air pollution in kitchen caused by cooking smoking is serious, usage of energy and sources is unreasonable, adaptability of requirement changing is limited, etc. the reasons contributing to the above problems are analyzed

    本文以調查現狀經濟適用住宅廚衛空間存在的問題為基礎，將其歸整為六大類主要問題，即：功能不完善；空間布局不合理；管線布置缺乏協調；廚房中油煙污染嚴重；資源能源的利用不合理；適應發展的能力不強。
  4. Based on the acquired data and operating experiences from pilot experiments, the demonstration project is devised comprehensively, which is concerned with so many aspects, such as choosing the site of demo plant, the portions " arrangement, gasification subsystem, condensation subsystem, tar catalytic reforming subsystem, purification and dryness subsystem, gas pipe networks and fire control subsystem. furthermore, economic assessment has been given preliminarily

    在中試試驗所獲得試驗數據和運行經驗的基礎上，進行了120戶規模的集中供氣示範工程的設計，包括氣化站選址及站內布置、氣化系統設計、冷凝系統設計、焦油催化裂解系統設計、凈化乾燥系統設計、輸氣管網設計、消防安全設計等，並進一步對項目的技術經濟性進行了簡單評估，為示範工程的建設和調試運行提供了技術保障。
分享友人
分享到 Line

分享到臉書