沾污量 的英文怎麼說

中文拼音 [zhānwūliáng]
沾污量 英文
dirt adherence
  • 沾 : 1 （浸濕） wet; soak; moisten 2 （被東西附著上） be stained with 3 （碰上; 挨上） touch 4 （得到...
  • 污 : Ⅰ名詞（臟水; 臟物） slops; sewage; dirt; filth Ⅱ動詞（弄臟） defile; dirty; smear Ⅲ形容詞1 （臟）...
  • 量 : 量動1. （度量） measure 2. （估量） estimate; size up
  1. The presence of a large density of contaminant causes anomalous increases in the diode current with increasing reverse bias.

    大量沾污也會使二級管電流隨反向偏壓的增加而呈現反常的增大。
  2. If bath king has been used for a long time, there will be feculence on the switch panel. when clear it, cut off power at first to make sure power off. and then use dishcloth with a little neutral detergent to rub it till the feculence is removed

    用戶長期使用浴霸，開關面板沾有污漬，在清理這些污漬時，應先切斷電源（零線和相線） ，並在確認沒電的情況下，用沾有少量中性清潔劑的抹布擦試，待污漬擦去后，再用清潔干布擦乾。
  3. When rub them, if power off, dismantle them, and than use dishcloth with a little neutral detergent to rub them till the feculence is removed. then use clean dry cloth to rub it again. when they are dry ( cannot insolate or firing ), install them again

    清潔面罩、暖燈或照明燈時，在確認切斷電源后，將暖燈、照明燈、面罩逐一拆下，用沾有少量中性清潔劑的抹布進行擦試，待污漬擦去后，用清潔干布進行擦拭，並在擦拭乾凈的燈體、面罩表面晾乾后（不可曝曬或烘烤） ，再進行安裝。
  4. To chemical measure, the higher molecular of peg is, the better result will be got ; to soap - free polymerization, on the contrary, the content of pmma enwrapping nano - silica effect few on results, which is obviously shown in data of stain resistance

    單從化學法本身看，接枝peg的分子量越大，結果越好，耐沾污性能表現尤為明顯；無皂乳液聚合也許由於本身方法的因素使得mma包裹量對結果影響不顯著。
  5. The mechanism is mainly that of mechanical entrapment where soiling increases with the weight and complexity of the fabric.

    沾污機理主要是機械地陷落，而且累積量將隨著織物的厚度和復雜性而增加。
  6. There exist large stress, intensive scratch, damage and pollution of ion in wafer process, so it is necessary to improve mechanism of slicing and lapping by changing single mechanical function to equilibrium chemical and mechanical function for small damage and low stress. reducing damage and stress and enhancing quality and efficiency of product result in a base of followed process so as to improve wafer process and enhance finished product ratio of whole wafer process

    目前加工過程中存在應力過大，造成表面劃傷嚴重，容易產生破損，離子沾污的問題，因而必須改善切削、研磨機理，把單一的機械作用變為均勻穩定的化學機械作用，以達到淺損傷、低應力的目的，有效的減少破損層和應力的累積，提高產品質量和加工的效率。
  7. For settle a great deal popularize and apply exterior wall coating, this paper study on acid rain - resistant, pollute - resistant, false accelerated aging - resistant of them. therein to, acid rain - resistant test is acid rain simulate test by environment quality data in chongqing. ph value is partly 0. 690, 0. 610, 0. 613, 0. 453

    為了解決重慶市外墻塗料不能大量推廣應用外墻塗料的重大難題，本文主要試驗研究三種不同主要成膜物（純丙、硅丙、氟樹脂）的外墻塗料的耐酸雨性、耐沾污性、耐人工加速老化等三大技術性能指標，其中耐酸雨性實驗是根據重慶市環境質量數據進行的酸雨模擬實驗， ph值分別為0 . 690 、 0 . 610 、 0 . 613 、 0 . 453 。
  8. Few disciplinarian can be found from the data of contact angle function and water absorbency. effects of temperature to stain resistance : with higher circumstance temperature, stain resistance will be lower, and more easily effected by content of nano - silica

    溫度對塗膜耐沾污性能的影響：一般是外界溫度越高，塗料耐沾污性能就越低，而且受納米含量影響更大。
  9. After the surface of nano - silica was modified, nano - coating is prepared by mixing nano - silica into polyacrylate emulsion. the properties of membrane formed have been proved to be improved. more emphasis will be put on analyzing stain resistance and scrubbing resistance

    改性后的納米二氧化硅在不同含量的情況下與聚丙烯酸酯乳液復合配成納米外墻塗料，研究其最終塗膜性能，並重點分析納米外墻塗料耐洗刷和耐沾污性能改善的情況。
分享友人
分享到 Line

分享到臉書