法向剛度系數 的英文怎麼說

中文拼音 [fǎxiànggāngdùxìshǔ]
法向剛度系數 英文
normal stiffness coefficient
  • 法 : Ⅰ名詞1 （由國家制定或認可的行為規則的總稱） law 2 （方法; 方式） way; method; mode; means 3 （標...
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 系 : 系動詞（打結; 扣） tie; fasten; do up; button up
  • 數 : 數副詞（屢次） frequently; repeatedly
  • 系數 : [數學] coefficient; ratio; modulus; quotient; factor
  1. In this paper, the rotating machinery at high speed is studied. there are discussed about numerical calculating methods for non - linear dynamical system, the rotor system radial impact and rubbing dynamics behavior analysis having the nonlinear rigidity on the unsteady and non - linear oil film, the rotor system dynamics behavior analysis with bending - torsional - pendular coupling vibrations, application of wavelet, fractal and network in fault diagnosis. the main works in this paper are as follows : ( 1 )

    本文以高速旋轉機械為主要研究對象，系統、深入地研究了非線性動力學系統的數值計算方法、具有非線性剛度的轉子系統在非穩態非線性油膜力作用下的徑向碰摩動力學行為、轉子彎扭擺耦合振動的動力學分析、小波和分形理論及人工神經網路在故障診斷中的應用問題。
  2. On the part of the design of nine - component thrust vector stand, an automatic hydraulic pressure original position calibration system, a scheme of original position calibration, and the great rigidity universal flexible combinatorial underprop are designed. by using the scheme of “ universal flexible combinatorial underprop plus software digital filter ”, the inherent frequency of test stand is improved, and the problem of test stand libration is solved. then, the resolving method of the disturbance between underprops of the moveable frame is proposed, and the disturbance revise equation is deduced

    在推力矢量試車臺設計方面，設計了自動液壓原位校準系統、原位校準方案以及大剛度萬向柔性組合支撐;採用「萬向柔性組合支撐+軟體數字濾波」的方案，提高了試車臺動架的固有頻率，解決了試車臺動架的振動問題;提出了動架約束互擾問題的解決方法，推導了互擾修正方程;研究了九分力推力矢量測量誤差分析方法，並計算了推力矢量測量精度。
  3. The software ansys6. 0 is used to analysis the stability of the state after construction of tongwamen bridge, linear method is used in analyzing the finite element model of the bridge, the coeffient of stability of different state after construction is given. on the basis, the effect of different factors such as the arrangement of lateral brace, the sloping angle of arch ribs, the stiffness of bridge deck system, the effect of non - orientedly conservative loadings of the hanger and tie bar etc is discussed. the different coefficients of stability of changing these factors are given, so the factors that are vital to the lateral stability of x - type arches are found, and the rationality of the methods taken to enhance the lateral stability of tongwamen bridge is evaluated

    本文應用有限元分析商業軟體ansys6 . 0 ，採用線彈性方法，通過對該橋的空間有限元模型進行穩定性分析，得出其成橋運營階段各種工況下的穩定安全系數。在此基礎上，本文還通過有限元模型分析，就拱的矢跨比、吊桿（立柱）的非保向力效應、橋面系的剛度、橫撐布置形式、拱肋側傾角等因素對該橋整體穩定性的影響展開探討與研究。文中給出了各因素變化情況下的穩定安全系數，指出了對鋼管混凝土提籃拱橫向穩定性有顯著影響的因素及其合理變化范圍，並對銅瓦門大橋提高橫向穩定性的措施的經濟合理性進行了分析。
  4. This paper deals with seismic analysis of an immersed tunnel using the travelling wave method the objective of the analysis is to obtain the maximum stresses in the tunnel body and the relative displacements at the joints for design purpose in analysis ， the axial and transverse input waves are treated as two independent waves with different amplitudes and periods the method has been found to have the advantages of simplicity and clearness in physical concepts however ， reasonableness of the prediction by the method depends largely on the input data ， such as the wave amplitude ， the wave length ， the propergation speed of the travelling wave as well as the reaction coefficient of the ground thus ， determination of the input data is discussed in detail finally ， the method is applied to analysis of huangsha - fangcun immersed tunnel across the pearl river in guangzhou

    將行波法應用到剛度較大、分段較多的水下沉管隧道的地震分析中，提出把軸向、橫向兩個輸入波處理為兩個獨立的行波的方法行波法是否符合實際，與輸入地震波的有關參數及地基系數選取有很大關系，作者對此進行了比較深入的討論，使輸入參數的選取簡單、明確，便於對計算結果進行分析與判斷最後應用此法對珠江水下隧道的工程實例進行了計算
  5. Using the complex potential method in the plane theory of elasticity of an anisotropic body, the series solution of finite anisotropic thin plate containing an elliptical inclusion is proposed with the help of faber series. a hybrid element with an elliptical inclusion for anisotropic materials is obtained by using the hybrid variable principle, and the element efficiency is verified by numerical examples. the state of the damage is modeled by an elliptical soft inclusion, and using the point stress criterion based on characteristic curve and yamada - sun etc. criteria, the prediction of the strength of a composite laminate with damage is set up

    首先基於經典層板理論，將復合材料層板的彈性問題化歸為均勻各向異性板來求解；採用各向異性體平面彈性理論中的復勢方法，以faber級數為工具，給出了有限大含橢圓核各向異性板彈性問題的級數解形式；利用雜交變分原理，成功導出含橢圓核各向異性板雜交應力有限元，並用算例驗證了該單元的可行性和有效性；採用含剛度折減橢圓形彈性核的沖擊損傷模型，引入基於特徵曲線和yamada - sun破壞準則的點應力判據，建立了含損傷復合材料層板剩餘強度的分析方法；通過數值計算詳細討論了各種幾何參數對損傷層板應力分佈、剩餘強度的影響，得到了一系列對工程應用具有實用價值的結論。
  6. ( 2 ) based on the existing theory of lateral load distribution rule, and combined the structure characteristic of pre - stressed lager cantilever composite beam with corrugated steel webs, this thesis proposed the modified rigid beam method. taking this method, it is facilitated to compute the lateral load distribution factor of bearing composite cantilever beam with variable - stiffness under the load in arbitrarily position

    （ 2 ）以現有的橫向分佈理論為基礎，結合大懸臂波形鋼腹板組合挑梁的結構特點，提出了修正剛接梁法的計算方法，能夠方便地計算變剛度懸臂組合梁任意點位的橫向分佈系數。
  7. And the impact of every parameters of f - ved element, stiffness coefficient and damper coefficient of ved element, normal stiffness, tangent stiffness and sliding friction of frd element and the cross - section area of the brace on the capability of dissipating vibration energy is computed and analyzed

    並對f - ved單元中ved單元的剛度系數、阻尼系數、 frd的法向剛度、切向剛度、滑動摩擦力及支撐橫截面面積等參數對單元阻尼效果的影響進行了分析研究。
  8. In the test, static - dynamic method is used to measure the stiffness, the eight stiffness coefficients of the radial part and the two stiffness coefficients of the thrust part can be obtained though loading slowly to the testing bearing which is in a equilibrium position

    首先，對處于平衡位置的測試軸承分別沿水平方向、鉛垂方向及軸向緩慢施加載荷，根據靜動法原理求得各個轉速下測試軸承徑向部分內、外膜8個剛度系數以及推力部分內、外膜2個剛度系數。
  9. By means of trigonometrical progression method and the mainline track spectrum, the sample function of the chinese mainline railway track random geometric irregularity is simulated. with the data obtained from track geometry inspection car on qinhuangdao - shenyang special line for passenger transport and arma time series model, the sample function of high - speed railway track random geometric irregularity are simulated. based on existing literature, the artificial bogie crawl waves at various different speeds are randomly simulated

    根據我國干線鐵路軌道譜，採用三角級數法模擬出干線鐵路和準高速鐵路軌道不平順的樣本函數；根據秦沈客運專線高速試驗段軌檢車資料，採用arma時間序列模型模擬了高速鐵路軌道不平順隨機樣本函數；在既有研究資料的基礎上模擬出各種速度客車構架人工蛇行波；用隨機變量描述道床橫向剛度，並進行了隨機模擬；將振動理論和穩定理論結合建立系統的分析模型和運動方程；根據monte ? carlo法編制了車輛?軌道耦合系統隨機振動分析程序，進行了無縫線路隨機動力響應分析，通過試驗對計算模型、計算方法進行了驗證。
  10. From basic equations of elastic mechanics, related knowledge of fracture mechanics and frequent used methods of differential and integral calculus, bending fracture models of anisotropic functionally graded materials is established by assuming that material constants ( stiffness matrix component ) are expressed in arbitrary functions

    根據彈性力學的基本方程以及斷裂力學的有關理論及微積分方法，將材料常數（剛度系數）設為空間變量的任意函數，建立了各向異性功能梯度材料板彎曲斷裂模型，即三類偏微分方程邊值問題。
  11. The flexible retaining structure is another important retaining structure in soft soil. the integrated numerical analysis of this retaining structure ( including the methods and theory of calculating active earth pressure under sorts of conditions as well as the calculating method of horizontal stiffness coefficient of bracing structure and the method of deciding boundary condition etc. ) was gived. the effect of all parameters on the characteristics of retaining structure was discussed using methods of sensitivity - analysis

    本文針對目前常用的彈性支點法，給出了完整的數值分析方法，包括各種條件下的墻後土壓力的計算方法和原理、支撐系統（或錨拉系統）水平剛度系數的計算、邊界條件的確定方法等，並以此為基礎採用靈敏度系數分析方法討論了各參數對圍護結構形態的影響，指出土體側向基床比例系數是影響圍護結構變形的最主要的參數。
  12. Steel structure of light - weight buildings with gabled frames is a widely used steel structural style in china at present. this paper starts with the deficiency of the specificaion in calculating the effective length factors of gable portal frames. when the gable portal frame subjected to the vertical uniform loading, it conducts the arch effect ? 1. rafter axial force is large when the slope of rafter is big

    門式剛架輕型房屋鋼結構體系是目前廣泛應用的一種結構形式，本文從規范中門式剛架柱的計算長度系數取值的不足出發，針對山形門式剛架在豎向均布荷載作用下產生的拱效應? ? 1 、斜梁傾角較大時產生較大的梁內軸力; 2 、產生跨變效應; 3 、高跨比較小的山形門式剛架會發生躍越失穩，採用整體分析的方法對山形門式剛架的穩定進行了分析。
  13. Combined with test research and current code, the practical design methods of the tier structure of multi - rib panel are researched chiefly. basic principles in the process of structure conception design are achieved, practical computing formulas for rigidity and load - bearing of the structure of multi - rib panel are deduced, practical design methods and process for buildings in the structure are expatiated, and actual project is seismic calculated as an example in this paper

    提出結構概念設計應遵循的基本原則，包括結構體系的適用范圍，房屋層數及高寬比限值，建築平面及豎向布置要求；給出復合墻板的剛度及承載力實用計算公式，並與試驗值進行對比；闡述了多層密肋壁板結構房屋的實用設計方法及設計步驟，並將實際工程作為算例，進行了詳細抗震驗算。
  14. In the analysis, a cfst arch ( single tube ) is first divided into a finite number of straight beam elements. according to the virtual work principle and the modified newton - raphson iteration method the tangent stiffness matrix considering double nonlinear properties is established. with regard to the non - equilibrium forces, the material nonlinear property along the height of the section and the length of the element is considered and the computation accuracy is improved as a result

    本文首先將拱肋劃分為一系列的直梁單元，運用虛功原理和修正newton - raphan數值迭代演算法的基本原理準確推導了拱肋直梁單元的非線性切線剛度矩陣；在不平衡力方面考慮了沿截面高度和單元長度方向材料非線性的發展過程，提高了計算精度；再根據得到的切線剛度矩陣採用荷載增量步內修正newton - raphan迭代的增量迭代法進行了求解。
  15. It is constructed that radial impact and rubbing dynamics differential equations of the rotor system having the nonlinear rigidity on the unsteady and non - linear oil film. the bifurcation and chaos behavior of impact and rubbing fault rotor system caused by the parameters of nonlinear rigidity, rotor rotating speed, eccentric mass is analyzed, in the numerical value analysis method. the bifurcation diagrams, maximum lyapunov exponent diagrams, poincar maps, phase plane portraits, trajectories of journal center, time - history curve, amplitude spectra diagrams of the rotor motion are used

    （ 2 ）建立了具有非線性剛度的轉子系統在非穩態非線性油膜力作用下的徑向碰摩動力學微分方程，並應用含高階余項的非線性動力方程的線性化數值法研究了此類系統響應的復雜動力學行為，利用轉子響應的分岔圖、最大lyapunov指數曲線、 poincar截面映射、時域波形、相軌線、軸心軌跡、幅值譜等圖形分析了系統響應的周期運動、擬周期運動、倍周期分岔、混沌等運動形式的轉化與演變過程，重點研究了非線性剛度、轉子轉速、偏心質量等系統參數對碰摩故障轉子系統的分岔和混沌行為的影響。
  16. Under the horizontal earthquake action and wind force, aim at " the pure frame structure with rectangle columns ", " the pure frame structure with special - shaped columns ", " the frame - truss structure with special - shaped columns " and " frame - shear wall structure with special - shaped columns ", earthquake action analysis was done by the spacial finite element method through the changes structural parameter. analyzing systematically " structure vibration mode ", " vibration period ", " structure lateral rigidity ", " seismic action force ", " seismic response force ", " floor seismic shear force ", " lateral horizontal displacement of structure " and " members internal force ". results indicate : ( 1 ) based on equal area, the special - shaped columns replaced the rectangle columns, the structural lateral rigidity enlarges, the lateral displacement minishes obviously, the earthquake response increase slightly, the biggest increasing amount of frame columns axis - compress ratio is smaller than 0. 08. the whole aseismic performance of structure has improved ; ( 2 ) when the section ' s length and section ' s thickness ratio of special - shaped columns is smaller than 3. 6, the structure benefits to resist seismic action ; ( 3 ) the angle of horizontal seismic action with the whole coordinate is 0 degree, structure earthquake response is bigger, belonging to a control factor of structure aseismic design ; ( 4 ) the frame - truss structure with special - shaped columns and the " a " - brace has the biggest lateral rigidity ; ( 5 ) the frame - shear wall structure with special - shaped columns have bigger lateral rigidity and smaller displacement, members internal force enlarged just rightly, have much superiority of resisting seismic action ; ( 6 ) in the higher seismic fortification criterion region ( 8 degree of seismic fortification intensity ), aseismic disadvantageous building site ( iii type site ), adopting special - shaped columns structure system, should reduce possibly the building ' s self - weight in order to reduce the earthquake response ; ( 7 ) the response spectrum method of computing seismic response and the time - history analysis method have similar analysis result

    西安理工大學碩士學位論文在水平地震作用下，並考慮風荷載組合，分別對「矩形柱純框架結構」 、 「異型柱純框架結構」 、 「異型柱框一析架結構」及「異型柱框-剪結構」等四種結構體系，通過改變結構參數，運用空間有限元方法，進行地震作用計算。系統地分析研究「結構振型」 、 「振動周期」 、 「結構側向剛度」 、 「結構地震反應力」 、 「樓層地震剪力」 、 「結構側向位移」 、 「層間位移角」 ，以及「構件內力」 。結果表明:在等面積原則下，異型柱代換矩形柱后，結構剛度增大，側向位移明顯減小，地震反應力略有增加，框架柱軸壓比最大增幅小於8 % ，結構整體抗震性能有所提高;當異型柱肢長肢厚比小於等於3 . 6時，結構有利於抗震;水平地震作用力與整體坐標夾角為0度時，結構地震作用效應較大，屬結構設計的控制因素之一;異型柱框一析架結構採用「人」字斜撐，側向剛度大於「八」字斜撐和「人一八」字混合斜撐;異型柱框一剪結構側向剛度大、位移小，構件內力增大適中，是一種抗震性能優越的結構體系:在抗震設防烈度較高地區（ 8度）和抗震不利的建築場地（ m類場地） ，採用異型柱結構體系時，應盡可能減輕結構自重，降低地震作用力;分別採用「振型分解反應譜」法和「時程分析」法進行地震作用計算，兩種方法所得結果基本一致。
  17. With the shearing deformation theory and deductive theory, the calculational formulas of flexibility coefficient of the pile head can be obtained. the interaction of the soil elements is calculated according to the layered - soil model. consequently, approximate analytical formulas of the flexibility matrix of piles - soil system, which undertake the vertical loads, come out

    採用剪切位移法，利用遞推原理導出樁頂柔度系數的計算公式;採用分層地基模型計算土體單元之間的相互作用，從而獲得承擔豎向荷載樁土支撐體系的柔度矩陣近似解析公式，進而得到樁土支撐體系剛度矩陣。
  18. Taking the analysis of elasticity as basis, thinking horizontal thick stick ' s stiffness, the bridge floor ' s stiffness and the force not guaranteed of the hanging bar synthetically ect, this paper drives pragmatic analysis method of stability of collapsing on arch bridge with thick stick through principle - energy encamping in value and haves carried out detailed discussion on every parameter

    摘要以彈性分析為基礎，綜合考慮橫撐剛度、橋面剛度、吊桿非保向力等因素，運用能量駐值原理建立了系桿拱橋側傾穩定分析的實用分析方法，並對各參數進行了詳細的討論。
  19. The paper carried out elastic response spectrum analysis on staggered truss frame system, input two strong ground motion records to carry out elastic and plastic time - history analysis. the paper compared the difference of aseismic property between 20 - storeyed composite truss and 20 - storeyed braced composite truss, and concluded that longitudinal brace can not only increase the rigidity but also reduce drift displacement of the first storey. in addition, the paper adopted displacement coefficiency in push - over method to obtain object displacement, and gave the failure modes of the two structures respectively

    本文對鋼結構交錯桁架體系進行了彈性反應譜分析、輸入了兩條強震記錄進行彈性以及彈塑性時程分析，對比了20層混合式和20層縱向帶支撐混合式在彈性階段及彈塑性階段的抗震性能區別，得出縱向帶支撐不但有利於增大縱向的剛度，還可以減小結構底層層間變形的結果；利用pushover的位移系數方法得出了結構的目標位移，並得出了兩種結構的破壞模式。
  20. It discusses the influence factors of pile groups effect, such as pile space, pile number, pile diameter, pile length and soil parameter etc. subsequently, using linear interpolation function to approximate the soil ' s anti force to piles, the article combines p - y curves with pole system fem. in this way, a new pile - soil interaction element calculated model is designed, the pile - soil interaction element stiffness matrix is deduced, and establishes finite element equation of p - y model, writes the relevant finite element program with matlab language, calculates and analyses pile groups subjected to lateral loads with engineering examples

    隨后，本文將p - y曲線法與桿系有限元法相結合，採用線性插值函數來逼近土對樁的約束反力，得到新的樁?土相互作用的單元計算模型，推導了樁?土相互作用的單元剛度矩陣，建立了p - y模型的有限元求解方程，用matlab語言編制了相應的p - y曲線有限元法計算程序，進行橫向承載樁的計算分析。
分享友人
分享到 Line

分享到臉書