法向應力效應 的英文怎麼說

中文拼音 [fǎxiàngyīnglìxiàoyīng]
法向應力效應 英文
normal stress effect
  • 法 : Ⅰ名詞1 （由國家制定或認可的行為規則的總稱） law 2 （方法; 方式） way; method; mode; means 3 （標...
  • 應 : 應動詞1 （回答） answer; respond to; echo 2 （滿足要求） comply with; grant 3 （順應; 適應） suit...
  • 力 : Ⅰ名1 （力量; 能力） power; strength; ability; capacity 2 [物理學] （改變物體運動狀態的作用） forc...
  • 效 : Ⅰ名詞（效果; 功用） effect; efficiency; result Ⅱ動詞1 （仿效） imitate; follow the example of 2 ...
  • 效應 : [物理學] effect; action; influence
  1. On this foundation the article inducts in detail the method which is based on the relative settlement of calculating unit area end support ( qb ) force at the same time considering the feature of pedestal pile ' s " arch effect " the article introduces conception of pile effective length and finally obtain t he formula of calculating man - made pipe with bulb - shaped axial carrying capacity. the article uses marc program to calculate and analyze foundation soil ' s stress and displacement and gets the change curve chart and the proportion that is shared by king - pipe side soil friction resistance and pipe end counterforce respectively. the article inducts the structure of pedestal in detail on the basis of generalizing pedestal application cases of many countries

    在此基礎上論文詳細歸納了以相對沉降為依據確定單位面積端承力q _ b的計算方法，並考慮擴底樁的「拱效應」特點引入了有效樁長的概念，最後結合公路規范推出了比較實用的人工挖孔擴底樁軸向承載力計算公式。論文運用了marc程序對地基土的應力和位移進行了有限元數值計算分析，得到了地基土的應力和位移場的變化曲線和在加載過程中樁側土摩阻力和樁端反力各自所承擔的比例；本文還在總結各國挖孔擴底樁應用情況的基礎上就擴底樁的構造進行了詳細的歸納。
  2. The welding technology of francis turbine runners is optimized from the view of subsection welding and local heating by numerical simulation. the result shows that welding residual tensile stress appears in the weld and its area nearby, and peak stress appears in the dangerous area of blades after practising quondam welding technology ; welding residual tensile peak stress in the dangerous area of blades can be decreased by welding both ends earlier and then welding middle section later during subsection welding, and decreasing effect on welding residual stress of the subsection welding is related to the weld length of blade outlets and welding direction of each subsection ; decreasing effect on residual stress of the local heating is direct proportional to heating time, heating temperature, heating area, and inversely proportional to cooling area, and welding residual tensile peak stress in the dangerous area is decreasing trend earlier, and then increasing trend later with heated location increased

    本文利用數值模擬手段對轉輪的焊接工藝從分段焊和局部加熱兩個方面進行了優化，結果表明:採用普通工藝焊接時，葉片焊后殘余拉應力出現在焊縫及其附近區域，並且在葉片出水邊的熔合線附近（危險區域）出現了峰值;在採用優化的分段焊時，先焊兩端后焊中間的方法可以降低葉片危險區域的焊接殘余拉應力峰值，降低效果與葉片出水邊焊段長度、焊縫各段的焊接方向有關;局部加熱法降低轉輪危險區域殘余應力的效果主要與加熱時間、加熱溫度以及加熱面積成正比，與冷卻面積成反比，並且危險區域的殘余應力隨加熱區域的增大呈先降低后升高的趨勢。
  3. Based upon virtual displacement method and the updated - lagrangian approach, stiffness matrices for two - dimensional elastic - plastic beam model in large displacement were proposed, in the derivation of which transverse stress was included because it was believed that part of the 2nd order effects of various stresses, which are in equilibrium with each other and with the external loads, will counteract each other and neglecting either part would possibly lead to incorrect results

    利用虛位移原理和更新的拉格朗日方法，導出了大位移彈塑性梁單元剛度矩陣的顯式表達式，在剛度矩陣推導中引入了截面內非線性剪應力和橫向應力的影響，剛度矩陣通過了剛體檢驗。之所以要引入橫向應力的影響，是因為本文認為，保持平衡所需的所有應力，它們各自的二階效應會相互抵消，因此忽略其中的任何一項都可能導致不正確的結果。
  4. On the basis, the effect of different factors such as the sloping angle of arch ribs, the stiffness of bridge deck system, the effect of non - orientedly conservative loadings of the hanger and tie bar etc is discussed

    此外，採用線彈性方法，就拱的吊桿的非保向力效應、橋面系的剛度、橫撐布置形式、拱肋側傾角等因素對該橋整體穩定性的影響展開探討與研究。
  5. The software ansys6. 0 is used to analysis the stability of the state after construction of tongwamen bridge, linear method is used in analyzing the finite element model of the bridge, the coeffient of stability of different state after construction is given. on the basis, the effect of different factors such as the arrangement of lateral brace, the sloping angle of arch ribs, the stiffness of bridge deck system, the effect of non - orientedly conservative loadings of the hanger and tie bar etc is discussed. the different coefficients of stability of changing these factors are given, so the factors that are vital to the lateral stability of x - type arches are found, and the rationality of the methods taken to enhance the lateral stability of tongwamen bridge is evaluated

    本文應用有限元分析商業軟體ansys6 . 0 ，採用線彈性方法，通過對該橋的空間有限元模型進行穩定性分析，得出其成橋運營階段各種工況下的穩定安全系數。在此基礎上，本文還通過有限元模型分析，就拱的矢跨比、吊桿（立柱）的非保向力效應、橋面系的剛度、橫撐布置形式、拱肋側傾角等因素對該橋整體穩定性的影響展開探討與研究。文中給出了各因素變化情況下的穩定安全系數，指出了對鋼管混凝土提籃拱橫向穩定性有顯著影響的因素及其合理變化范圍，並對銅瓦門大橋提高橫向穩定性的措施的經濟合理性進行了分析。
  6. Along with the progress of drilling technology, many new types of bha such as steering motor assembly, dropping assembly with eccentric bend sub, dropping assembly with flexible connection are developed based on common building, dropping and holding assemblies. for using these bha, a new mathematical model is put forward for 3d static analysis of these types of bha under small deflection. and its weighted residual solution is given. the mathematical model includes ( 1 ) differential equations ; ( 2 ) boundary conditions at drill bit, stabilizer, bend angle, diameter change, tangential point and borehole wall ; ( 3 ) lateral forces and deflection angles of bit. the software based upon this method runs well

    為了更好地應用各種新鉆具，建立了適用於對普通下部鉆具、導向鉆具、帶偏心彎接頭和柔性接頭的下部鉆具進行三維小撓度靜力學分析的數學模型，包括（ 1 ）微分方程； （ 2 ）鉆頭、穩定器、彎角、變截面、切點和井壁的邊界條件； （ 3 ）鉆頭的側向力和鉆頭轉角.給出了該模型的加權余量解.用該方法編寫的軟體應用效果良好
  7. Obtain these chief research achievements. ( 1 ) the method of hydraulic fracturing, kaiser effect experiment and the finite element numerical simulation computation results, the direction of maximum horizontal principal stress intersect the small - angle of tunnel axial line, it is favorable to the stability of tunnel peripheral rock ; according to the test rust of field stress - relief method, at the present time, zhe gu mount tunnel have n ' t access to high crustal stress site, maximum principal stress magnitude is 17mpa ~ 20mpa

    主要獲得以下研究成果： （ 1 ）綜合水壓致裂法、室內巖石kaiser效應試驗和有限元數值模擬計算研究成果，最大水平主應力方向與隧道洞軸線小角度相交，對隧道圍巖穩定性有利；根據現場應力解除法測試結果，目前鷓鴣山隧道尚未進入高地應力段，最大主應力量級為17mpa 20mpa 。
  8. Here, fem is applied in the analyses of i ) fiber axial stress and interphase shear stress in fragmentation tests during initially applied strain, ii ) influence of temperature on the stress transfer across the interface, iii ) modulus and thickness of the interphase and their influence on interfacial stress transfer, iv ) interfacial debonding process, and v ) fragment aspect ratio, contact friction along the interface and their influences to the interfacial stress transfer efficiency

    在論文的這部分工作中，使用有限元法描述和分析了逐節斷裂試驗中初始應變下的纖維軸向應力和界面相剪切應力，溫度對界面應力傳遞的影響，界面相模量和厚度、纖維節長寬比、界面脫粘過程、界面接觸中的摩擦效應等因素對逐節斷裂試驗中應力傳遞的影響。
  9. Furthermore, the fiber volume fraction of each inclined and horizontal unidirectional " lamina was assumed to be the same as that of the composites. three - dimensional stress - strain analysis was applied to each unidirectional lamina that was assumed to be transversely isotropical under on - axis coordinate system. carrying out the integration and averaging of stiffness yielded the effective elastic moduli of 3 - d braided structural composites

    採用三維應力?應變分析，在單胞的長度方向積分和平均，在給定的應變邊界條件下，採用剛度體積平均的方法，預測三維編織結構復合材料的有效彈性模量；在空間多向應力的基礎上，通過對三維編織結構復合材料破壞機理的探討，摘要提出了適用於三維編織復合材料細觀強度失效準則，預測三維編織結構復合材料的強度性能。
  10. Two types of seismic calucation methods that are response spectrum analysis and time - history analysis are used to analyze the seismic response of kiewitt ' s suspen - dome under lateral seismic action and vertical seismic action. the result obtained by above - mentioned methods and the code method are compared. genetic algorithm method is proposed to optimize the prestress of suspen - dome

    本文採用振型分解反應譜法和時程分析法兩種方法，對kiewitt型弦支穹頂預應力結構的水平和豎向地震作用下的地震效應進行計算分析，並同現行的規范和規程的規定方法一10重力荷載代表值簡化法計算結果進行了比較分析。
  11. Determination method of the damage threshold stress and damage threshold strain is given, six kinds of damage variables ( which are across isotropy effectual elastic modulus damage variable, simple effectual elastic modulus damage variable, density damage variable, volume damage variable, volume density damage variable and area density damage variable ) are defined, evolution curves and evolution equations of harden yield damage are obtained

    提出了損傷應力和應變門檻值的確定方法，並定義了六種損傷變量（即橫觀各向同性有效彈性模量損傷變量，簡單有效彈性模量損傷變量，密度損傷變量，體積損傷變量，體積密度損傷變量和面積密度損傷變量） ，在此基礎上得出了硬化屈服損傷過程中的損傷演化曲線和演化方程。
  12. The contents include : based on the previous research and the data of experimentations, the author researches and develops a kind of satisfactory semi - empirical formula of nonlinear temperature distribution, and calculates the temperature stress of rigid - framed arch bridge by the fem. the temperature effects of bridge structure by annual and sunlight temperature difference are discussed, it indicates that the temperature effect of annual temperature difference is small but the temperature effect of sunlight temperature difference is great and the temperature stress along beam depth resulted from sunlight temperature difference is nonlinear. with the comparison between the temperature effects of different position of bridge, the results show that where the section of bridge is small, the temperature stress of it is large

    本文主要包括以下內容：從理論上研究並結合實測資料發展了一種比較理想的半經驗溫度場非線性分佈公式，並將有限元方法應用於剛架拱橋結構溫度應力的計算中，對橋梁結構進行整體溫度應力分析；討論了年溫差和日照溫差引起的橋梁結構的溫度效應，表明年溫差引起的溫度效應較小，而日照溫差引起的溫度應力較大且沿梁高呈非線性分佈；分析比較了橋梁結構各個部位的溫度效應的大小，可知截面越小溫度拉應力越大，受力越不利；並對箱梁結構由於構造不同引起的縱向與橫向的溫度效應大小進行了探討，發現在頂板下緣也會出現相當大的溫度拉應力，並且梗腋的存在反而增加了頂板底部的溫度拉應力；還對幾種相近的剛構式橋型的溫度效應進行了分析對比，總結了這些橋型針對溫度效應的優劣，並提出相應的針對性措施。
  13. This paper deals with seismic response of a tunnel - soil system immersed tunnel ， as an underground structure ， must be compatible with the deformation of the surrounding soil thus the simplified model for a tunnel - soil system is established through two steps at the first step ， an mdof system is developed for modeling the foundation soil to this end ， dynamic behavior of the foundation soil is analyzed a typical section of the foundation soil simplified as a single mass - spring system on the basis of some equivalent criteria those mass are linked longitudinally by elastic springs to form an mdof system at the second step ， the tunnel is treated as a beam on elastic foundation ; that is ， the tunnel is connected with the soil massed to form a tunnel - soil system this model has been applied to the seismic analysis of huangsha fangcun immersed tunnel across the pearl river in guangzhou design recommendation is proposed on the basis of this analysis

    研究沉管隧道在地震條件下整體受力的分析方法分兩步建立計算模型第一步通過分析場地地基土切片的動力特性，根據等效原則將其化為等效單質點體系，然後在縱向用等效彈簧連接而成為多質點體系的地基土計算模型；第二步將隧道看作彈性地基梁與上述多質點體系通過等效彈簧連結而得到土隧道體系的計算模型本文結合廣州黃沙芳村珠江水下隧道工程實例建立了具體的計算模型並對多種不同的約束條件，進行了縱向與橫向地震響應時程分析，為該隧道的抗震設計提供依據
  14. Using the complex potential method in the plane theory of elasticity of an anisotropic body, the series solution of finite anisotropic thin plate containing an elliptical inclusion is proposed with the help of faber series. a hybrid element with an elliptical inclusion for anisotropic materials is obtained by using the hybrid variable principle, and the element efficiency is verified by numerical examples. the state of the damage is modeled by an elliptical soft inclusion, and using the point stress criterion based on characteristic curve and yamada - sun etc. criteria, the prediction of the strength of a composite laminate with damage is set up

    首先基於經典層板理論，將復合材料層板的彈性問題化歸為均勻各向異性板來求解；採用各向異性體平面彈性理論中的復勢方法，以faber級數為工具，給出了有限大含橢圓核各向異性板彈性問題的級數解形式；利用雜交變分原理，成功導出含橢圓核各向異性板雜交應力有限元，並用算例驗證了該單元的可行性和有效性；採用含剛度折減橢圓形彈性核的沖擊損傷模型，引入基於特徵曲線和yamada - sun破壞準則的點應力判據，建立了含損傷復合材料層板剩餘強度的分析方法；通過數值計算詳細討論了各種幾何參數對損傷層板應力分佈、剩餘強度的影響，得到了一系列對工程應用具有實用價值的結論。
  15. Fabrication of the box beam is divided into such parts as reinforcement, formwork, concreting, prestressing, moving and storing of beam, pipe grouting under pressure, end sealing of the beam, water - proof layer on the bridge surface system, protective coating etc. the paper makes description of effective box beam construction technology and workmanship which can be adopted in other projects, such technologies as : manufacturing and fixing of reinforcement, steel reinforcement fixing baseplate, web plate and top plate respectively and lifting the steel skeleton into form, requirements of design and manufacturing and way of utilization for dismantling - erection type formwork and hydraulic formwork, optimization of concrete ratio, concrete pouring process of two ends of beam in priority over the middle, in sequence of first baseplate followed by web plate and top plate at last, concrete pouring in inclined section and in horizontal layer, concrete vibration mainly by external vibrator in assistance with internal vibrator, methods and regulation for steam curing of concrete, dual controls over stress and strain to ensure quality of prestressing workmanship, construction method of effective beam moving by heavy - weight special moving facility, some regulations and key notes about construction of grouting under pressure, beam ends sealing, water - proof layer on the bridge surface system, protective coating

    箱梁製造由鋼筋工程、模板工程、混凝土工程、預應力工程、移存梁工程、孔道壓漿工程、梁體封端工程、橋面防水層和保護層工程等施工環節組成。文中介紹的採用胎具製作和綁扎鋼筋，分底腹板和頂板分別綁扎並吊裝鋼筋骨架入模；拆裝式和液壓式兩種模板的設計、製作要求和使用方法；綜合考慮、優化混凝土配合比，混凝土灌注從兩端至中間、先底板、后腹板、再頂板的施工順序和斜向分段、腹板水平分層、附著式振搗為主、插入式搗固為輔的施工工藝，蒸汽養護的方法和規定；應力應變雙控制確保預應力施工質量的施工技術；採用重物移運器有效移梁的施工方法；壓漿、封端、橋面防水層和保護層施工的一些規定和注意事項等都是對箱梁製造行之有效的施工技術和施工方法，並可為以後類似施工作借鑒。
  16. 3. feasibility analysis of mbs the paper introduces and explains the theory of mbs and analysis the feasibility of mbs in china from many aspects, such as system, laws, financial environment, the situation of housing markets, macroeconomic effect, etc. the reform of land - using system provides mbs system pre - requisite ; the interrelated laws offer the law guarantee for mbs ; the issue of " security act " indicates that the security market of china is being normalized, and the developing prospect of finance in china brings mbs effective support ; the dilemma between the surplus and the shortage of commercial housing gives mbs an important turning point ; the macroeconomic effect of mbs is that it accelerates the economy, reduces the pressure of currency inflation, dissolves the operating risks of finance organs and makes the finance system operate steadily

    三、我國住房抵押證券化的可行性分析本文從住房抵押貨款證券化（ mbs ）的理論分析入手，結合我國住房抵押貸款的發展狀況，分別從制度、法律保障、金融環境、住房市場現狀、宏觀經濟效應等幾方面論述了mbs在我國的可行性：土地使用制度改革為實施mbs提供了制度前提；配套法律制度為實施mbs提供了法律保障； 《證券法》的正式出臺，標志著我國證券市場走向規范，我國良好的金融業發展前景為mbs提供了有效的支持；現階段住房市場的有效供給與有效需求雙重約束的矛盾存在，為證券化實施提供了重要契機； mbs的宏觀經濟效應在於拉動國內需求，促進經濟增長，減輕通貨膨脹壓力，化解金融機構經營風險，保持金融體系穩定運行。
  17. The article consists of three parts mainly : the first part has described the method of detecting the faint signal, mainly include : detection technique of faint signal, principle of the optical fibre sensor, the little lose effects when optic fibre little curved, and the research of the stress sensor of optical fibre. the second part emphasizes on the design of the intelligent photoelectricity system, mainly tells the design of the circuit to process the faint photoelectricity signal, details the software and hardware design of intelligent photoelectricity system made of single chip microcontroller, led, man - machine interface, communication interface, etc. the third part is the network communication of the detection system, details the technology of single chip microcontroller how to group the network, and the communication between single the chip microcontroller system and the modem, and how to realize the data between the field and computer central exchanged through the existing public phone network

    文章主要分為三部分：第一部分論述了微小信號的檢測方法，主要包括微小信號的檢測技術、光纖傳感器的原理、光纖微彎損耗效應及光纖應力傳感器的研製；第二部分重點講述了智能光電檢測系統的研製，主要講述了微弱光電信號調理電路的設計及由前（后）向通道、單片機、 led 、人機介面、通信介面等組成的智能光電系統的軟硬體的具體設計；第三部分為檢測系統的網路通信部分，具體闡述了單片機系統間的組網技術、單片機和modem之間的通信及通過現有的公用電話網路實現遠程監控的技術，實現現場檢測系統與橋梁測控中心的數據交換。
  18. The expression can be used in calculation for relationships of the input voltage, output voltage and device geometry parameter

    用漸近解的分析方法對所求到的解進行簡化，導出了硅橫向壓阻效應四端壓力傳感器的輸出電壓表達式。
  19. A valid method to make the anisotropic deformation behavior of load bearing unit clear is to research principal stress and principal strain relationship, and true triaxial test is a necessary means

    弄清受荷單元的主應力主應變關系是認識各向異性變形性狀的有效方法，而真三軸試驗是必要的手段。
  20. Furthermore using the variation principle in the elasticity, the wave - motion equation is derived in the finite deformation elastic thin rod with viscous and transverse inertia effects, and the characteristic curves and their characteristic relations are obtained by characteristic line method, and the influence of viscous and geometrical - dispersive effects on the propagation of wave is analyzed

    再利用彈性力學中的變分原理，導出了同時計及粘性和橫向慣性效應時的彈性細桿的幾何非線性波的波動方程，用特徵線法得到它的特徵線和特徵線上的相容關系，分析了粘性耗散和幾何彌散效應對波的傳播速度的影響。
分享友人
分享到 Line

分享到臉書