法向應力系數 的英文怎麼說

中文拼音 [fǎxiàngyīnglìxìshǔ]
法向應力系數 英文
normal stress coefficient
  • 法 : Ⅰ名詞1 （由國家制定或認可的行為規則的總稱） law 2 （方法; 方式） way; method; mode; means 3 （標...
  • 應 : 應動詞1 （回答） answer; respond to; echo 2 （滿足要求） comply with; grant 3 （順應; 適應） suit...
  • 力 : Ⅰ名1 （力量; 能力） power; strength; ability; capacity 2 [物理學] （改變物體運動狀態的作用） forc...
  • 系 : 系動詞（打結; 扣） tie; fasten; do up; button up
  • 數 : 數副詞（屢次） frequently; repeatedly
  • 系數 : [數學] coefficient; ratio; modulus; quotient; factor
  1. Based on the close analysis of the influence factors of the vertical bearing capacity, circular aperture extension theory is employed to establish the computing formulas for the pile vertical stress and the foundation vertical bearing capacity, respectively. moreover, with analyzing the features of the calculation parameters such as materials of gunite mortar, jet pressure, diameter of the jet pipe, pile length, pile layout, a design theory for chemical churning pile composite foundation is proposed. then, the variation of the pipe deformation with loads, the deformation coordination of pile and soil are studied

    在此基礎上深入探討了旋噴樁的樁土受力特性及其復合地基的加固機理，從影響旋噴樁復合地基豎向承載力的因素入手，基於圓孔擴張理論給出了樁體豎向應力及旋噴樁復合地基的豎向承載力計算公式;通過對噴射漿液、噴射壓力選取、噴射直徑估算、樁長及樁位設計等各種計算參數的深入分析和研究，提出了一套相應的旋噴樁復合地基設計計算方法;通過計算分析，深入探討了旋噴樁復合地基變形隨荷載變化規律、樁和樁間土變形協調關系、樁土應力比及復合地基壓縮模量的確定，並提出相應的設計方法和修正參數;此外，結合工程應用，對旋噴樁復合地基的施工技術及其現場質量檢測方法進行了較全面的探討。
  2. Choose two nodes on the edge of the structural to compare the results calculating by the finite element program midas, then we can draw a conclusion that these kinds of space truss systems is sensitive to the libration of the dynamic wind loads. to consider this factor is very necessary in the process of design, we will use the pulsant augmentation coefficient to realize it

    比較靜力風荷載和動力風荷載作用下的有限元軟體的計算結果，選取結構邊緣部分的兩個節點，對比它們在兩種方法計算下的最大位移的計算結果。經過比較可以看出重量輕、頻率低、阻尼小的柔性建築物對風荷載的橫向振動是很敏感的，在進行工程設計時應該考慮這種因素，並可採用乘以風振系數等相應方法來加以體現。
  3. The software ansys6. 0 is used to analysis the stability of the state after construction of tongwamen bridge, linear method is used in analyzing the finite element model of the bridge, the coeffient of stability of different state after construction is given. on the basis, the effect of different factors such as the arrangement of lateral brace, the sloping angle of arch ribs, the stiffness of bridge deck system, the effect of non - orientedly conservative loadings of the hanger and tie bar etc is discussed. the different coefficients of stability of changing these factors are given, so the factors that are vital to the lateral stability of x - type arches are found, and the rationality of the methods taken to enhance the lateral stability of tongwamen bridge is evaluated

    本文應用有限元分析商業軟體ansys6 . 0 ，採用線彈性方法，通過對該橋的空間有限元模型進行穩定性分析，得出其成橋運營階段各種工況下的穩定安全系數。在此基礎上，本文還通過有限元模型分析，就拱的矢跨比、吊桿（立柱）的非保向力效應、橋面系的剛度、橫撐布置形式、拱肋側傾角等因素對該橋整體穩定性的影響展開探討與研究。文中給出了各因素變化情況下的穩定安全系數，指出了對鋼管混凝土提籃拱橫向穩定性有顯著影響的因素及其合理變化范圍，並對銅瓦門大橋提高橫向穩定性的措施的經濟合理性進行了分析。
  4. Abstract : based on thestatic wind force factors of a tower and on the root - mean - square of the buffetingdisplacement responses of the tower top, which are measured by wind tunnel tests inlaminar and turbulent field respectively, the static and buffeting internal forces of thetower bottom control sections under its design wind speed are obtained by linearsuperposition method and fem

    文摘:基於均勻流和紊流風場中的橋塔模型風洞試驗所測得的橋塔空氣力靜力系數及塔頂抖振響應的位移均方根，採用線性疊加法及有限元法反演，給出設計風速下塔底控制截面的順風向靜風及抖振內力。
  5. It is to use finite element method to calculate the stress within the slope in this paper, and get the normal stress and tangent stress of the slope sliding surface directly, and then calculate the stability coefficient of the slope

    本文研究內容是應用有限元法計算斜坡內部的應力，並直接求解邊坡滑動面上的法向力和切向力，進一步計算邊坡的穩定系數。
  6. Using the complex potential method in the plane theory of elasticity of an anisotropic body, a series solution to the stress field of a finite plate containing multiple cracks subjected to arbitrary loads is obtained by means of the faber series expansion, and the stress intensity factors at the crack tips are calculated based on the theories of fracture mechanics. equivalence yield stress is introduced in order to consider the effects of the plastic zones, with which the strip yield criteria is developed in the article so that the effects of structural size and the crack interactions on the stress distribution can be considered accurately. the effects of plate size, crack size and crack distributions on the stress intensity factors as well as the residual strength of the plate are studied detailedly

    採用各向異性體平面彈性理論中的復勢方法，以faber級數為工具，得到了含多裂紋有限大板在任意載荷作用下應力場的級數解，並應用斷裂力學方法確定裂紋尖端的應力強度因子；引入當量屈服應力考慮裂尖塑性區的影響，提出基於帶屈服準則的剩餘強度分析模型，能夠充分考慮結構尺寸和裂紋之間相互作用對應力場的影響；通過數值計算詳細討論了結構尺寸和裂紋之間位置關系對應力強度因子和結構剩餘強度的影響規律，得到了一系列對工程應用具有實用價值的結論。
  7. Using the complex potential method in the plane theory of elasticity of an anisotropic body, the series solution of finite anisotropic thin plate containing an elliptical inclusion is proposed with the help of faber series. a hybrid element with an elliptical inclusion for anisotropic materials is obtained by using the hybrid variable principle, and the element efficiency is verified by numerical examples. the state of the damage is modeled by an elliptical soft inclusion, and using the point stress criterion based on characteristic curve and yamada - sun etc. criteria, the prediction of the strength of a composite laminate with damage is set up

    首先基於經典層板理論，將復合材料層板的彈性問題化歸為均勻各向異性板來求解；採用各向異性體平面彈性理論中的復勢方法，以faber級數為工具，給出了有限大含橢圓核各向異性板彈性問題的級數解形式；利用雜交變分原理，成功導出含橢圓核各向異性板雜交應力有限元，並用算例驗證了該單元的可行性和有效性；採用含剛度折減橢圓形彈性核的沖擊損傷模型，引入基於特徵曲線和yamada - sun破壞準則的點應力判據，建立了含損傷復合材料層板剩餘強度的分析方法；通過數值計算詳細討論了各種幾何參數對損傷層板應力分佈、剩餘強度的影響，得到了一系列對工程應用具有實用價值的結論。
  8. The article consists of three parts mainly : the first part has described the method of detecting the faint signal, mainly include : detection technique of faint signal, principle of the optical fibre sensor, the little lose effects when optic fibre little curved, and the research of the stress sensor of optical fibre. the second part emphasizes on the design of the intelligent photoelectricity system, mainly tells the design of the circuit to process the faint photoelectricity signal, details the software and hardware design of intelligent photoelectricity system made of single chip microcontroller, led, man - machine interface, communication interface, etc. the third part is the network communication of the detection system, details the technology of single chip microcontroller how to group the network, and the communication between single the chip microcontroller system and the modem, and how to realize the data between the field and computer central exchanged through the existing public phone network

    文章主要分為三部分：第一部分論述了微小信號的檢測方法，主要包括微小信號的檢測技術、光纖傳感器的原理、光纖微彎損耗效應及光纖應力傳感器的研製；第二部分重點講述了智能光電檢測系統的研製，主要講述了微弱光電信號調理電路的設計及由前（后）向通道、單片機、 led 、人機介面、通信介面等組成的智能光電系統的軟硬體的具體設計；第三部分為檢測系統的網路通信部分，具體闡述了單片機系統間的組網技術、單片機和modem之間的通信及通過現有的公用電話網路實現遠程監控的技術，實現現場檢測系統與橋梁測控中心的數據交換。
  9. With the support of methodology and approaches pertaining to medicine, psychology and physiology, this research explores the correlation among speed, roadway alignment, environment and physiological and psychological element of driving behaviors on the basis of abundant data obtained from field study, which lays the foundation for further analysis of what represents a comfortable and safe situation and for the calibration of threshold value of coefficient of transverse force

    本研究應用醫學和心、生理學方面的理論方法和研究手段，通過大量的行車試驗，尋找汽車行車速度、道路線形、道路環境與駕駛員行車心、生理需求的內在關系和規律。以此為基礎，研究在山區雙車道公路上行車，緊張與不緊張，安全與不安全的條件，研究橫向力系數等的極限值。
  10. According to the documentation collected from domestic and abroad wang wei dong who works in huadong architect and structure institute utilizes the similar work property between the underground continuous wall and pile subjected the vertical loads, and introduces poulos method of elasticity and plastic which applies to pile foundation into the calculation for subsidence of underground continuous wall. pujialiu and yu yuzhou from water and electronic engineering of qinghua university, according to the result of three axes, define the concrete parameter utilize the model of non - linear e - b combined with the design cross section of dam in xiaolangdi, yellow river accept the total stress programme of thepd dam, and we analyze the stress and displacement of plastic concrete diaphragm wall by finite element method in comparison with the result of common concrete one. at same time, we consider the effect of the character of plastic concrete diaphragm wall which is composed of different gradients and adopting the level of stress and pulling stress infers whether the plastic concrete diaphragm wall is safe or not

    地下連續墻是一種歷史較短的施工方法，目前，砼防滲墻的設計還是以傳統的設計方法為主，根據查找國內外文獻資料，華東建築設計院王衛東利用地下連續墻與樁在豎向荷載作用下的工作性能有相似性，將適用於樁基的poulos彈性理論引入對地下連續墻的沉降計算中；清華大學水利水電工程系濮家騮、于玉貞根據三軸試驗結果確定混凝土的參數，利用非線性e - b模型，結合黃河小浪底土石壩設計剖面，採用thepd土石壩總應力程序，對深覆蓋層塑性混凝土防滲墻的應力、位移進行有限元分析，並與普通混凝土防滲墻計算結果加以對比，同時分析了不同配比塑性混凝土特性的影響，並採用應力水平和拉應力數值來判斷塑性混凝土防滲墻的安全程度。
  11. The soccer robot system is a dynamic environment with multiple obstacles. it is a problem of high complexity to perform path planning in such environments. the traditional methods are not efficient in such complex environments. in this paper, a self - learning method of robot navigation is proposed based on the reinforcement learning method and artificial potential field method

    本論文將增強式學習演算法和人工勢場法相結合，提出狀態評價函數和勢場的對應關系，以及控制策略和勢場力方向的對應關系，通過機器人的自適應學習，來形成優化的人工勢場，使機器人能夠以最短路徑繞過障礙，到達目標。
  12. When there is no or lesser undercut, we can use the bend stress ' s algorithm of involute gear to calculate approximately the bend stress of gear with meshed medium belt, what we to do is to transit the interrelated shift coefficient to the according radial minus shift coefficient of involute gear, and the error can be controlled in 10 %

    在不產生或少量根切時，可用漸開線徑向變位齒輪的彎曲應力計算方法來近似計算帶式嚙合介質齒輪的彎曲應力，只需將關聯變位系數轉化為相應的漸開線齒輪徑向變位系數即可，其誤差在10 %以內。
  13. On the basis, three elastic calculation coefficients of the two - way composite slab on three common boundary conditions are deduced and calculated by applying the classic elastic plane theory. in the thesis, the elastic design methods of pk prestressed composite two - way slab is explored and studied by the example. furthermore, it is also studied how to apply the yield - line design method to design the prestressed two - way composite floor slabs

    本文以此為依據，應用經典彎曲薄板理論，採用李維法推導和計算了這種雙向樓板三種常見邊界下的撓度和內彎矩彈性計算系數，並在此基礎上通過算例探討了pk預應力雙向疊合樓板的彈性設計方法，同時還對其塑性鉸線設計方法進行了研究。
  14. According to the fluctuating property of wind, on the stochastic vibration finite element theory, some calculation formulas of the response, including the along - wind response and the across - wind response, are obtained, the ideology of the torsion vibration in the double - tower structure and the ideology of the double - tower structure ' s dynamical wind load are also put forward at the same time. by using the stochastic vibration module of the general finite element program, the paper analyses the performance of the wind resistance more deeply and fully, discussing the influence on the double - tower structure from the diversification of the different component. the variance law of dynamic displacement and wind - induced vibration coefficient is derived through analyzing structure stochastic vibration, so is the effect of several parameters on dynamic displacement, acceleration and wind - induced vibration coefficient

    從結構風振的基本理論出發，通過對脈動風功率譜的分析，推導了結構風振響應（順、橫風向）的計算公式，同時提出了雙塔結構的扭轉振動和動力風荷載計算的思想，在結合通用有限元程序的隨機振動模塊的情況下，對雙塔結構的抗風性能作了深入、全面研究，探討了雙塔結構構件截面的變化對其抗風性能的影響，同時探討了順風向風速譜的選取、風速、參與計算的振型數、風與結構耦合作用是否考慮等因素對分析結果的影響，比較了規范風振系數的計算與隨機演算法結構的異同，並討論了原因，得出一些有意義的結論。
  15. By means of the theoretical analysis of the micromachined vibratory rate gyroscope, we get following conclusions : the microgyroscope can be driven by tangent electrostatic force produced by fence structure electrodes, and the normal electrostatic force can be neglected for the influence of the device property ; the parasitical capacitance and fringing effect can ’ t be neglected for the calculating of the detection capacitance ; the coefficient of damping force is comparatively little when the air damping in the driving mode and the sensing mode of the device is the couette flow damping

    主要內容如下: 1 .分析了微機械陀螺的運動特性、靜電驅動特性和在大氣下的阻尼特性，分析結果表明，可以運用切向靜電力驅動質量塊振動，法向靜電力對器件特性的影響可以忽略;在計算微結構電容時，電容的邊緣效應和寄生電容不可忽略;在器件所受阻尼主要為庫埃特流阻尼的情況下，阻尼力系數較小。
  16. In this research, fatigue life of laminate composite is predicted phenomenologically, dealing mainly with in - plane stresses without accounting for out - of - plane failures such as delamination. fatigue modulus is used as a physical parameter which helps to describe the basic fatigue behaviour of unidirectional laminates and obtain expressions for cumulative damages defined by strains. based on some typical fatigue test data for unidirectional composite laminates, a cumulative fatigue damage model is presented for predicting the fatigue life of multidirectional laminates with arbitrary stacking sequence under complicated fatigue loadings

    本文以碳纖維/樹脂基t300 / qy8911層壓結構為研究對象，從唯象的觀點出發，以疲勞模量為參量構造損傷函數，基於幾組最典型的單向板疲勞試驗數據，建立單向板在多軸循環應力作用下的疲勞壽命模型，並以此為基礎，發展同種材料體系的任意鋪層形式的多向層壓板在復雜循環載荷作用下的疲勞壽命預測方法。
  17. With the consideration of the vertical wave effect of soil and soil - pile interaction, an approximate analytical solution to vertical vibration of pile system with variable impedance in visco - elastic layered soil is developed. a simplified and practical mathematical model for interaction between soil layers is proposed, and its applicability is theoretically investigated. based on this model and by using laplace transforms and the transmit property of impedance function, the analytical expression of the impedance function and solutions of the displacement and velocity response function in frequency domain and in time domain at the pile head are derived

    4 、從三維軸對稱土模型出發，對考慮樁土耦合作用、土層層間聯系以及樁周土豎向應力梯度變化條件下的成層粘彈性土中完整樁及變阻抗樁系統縱向振動問題進行了研究，提出了成層土中變阻抗樁系統縱向振動問題的近似解析解法和樁周土層層間相互作用的簡化而實用的數學模型，並利用拉氏變換和阻抗函數的傳遞性，獲得了成層土中任意段變阻抗樁樁頂阻抗函數的解析表達式，以及樁頂速度導納和時域速度響應解析解和半解析解。
  18. With the help of this program, this paper does research on the moved backwards of the slide surface, lengthening the anchor section, the soil nail ' s total force, gets conclusion about relations between the soil nail ' s length and the slope ' s grade, height, soil ' s mechanical parameter ; relations between soil nail ' s total force and coulomb soil pressure. with the help of the large multiuse finite element program ansys, this paper analyzes the soil nailing in one - step ' s slopes, in two - steps " slopes, puts the emphasis on the axis force ' s distributing along the soil nail at each rows, the effect of both the excavating mode and the original slope figure to the axis force of the soil nail, the one another effect between the upper - step slope and the nether - step slope in the soil nail ' s axis force, gets conclusion about the design of soil nail at the first low, different slope body is the same with different excavating mode, the original slope figure has more effect to some than others because of the slope body, the reasonably design of the step width in two - steps slopes, the two - steps excavating and retaining has more virtue than the one - step ' s. through soil pressure analysis this paper does research on the differences and the links between the coulomb soil pressure theory and the rankin ' s, the vertical pressure at the slope surface when the slope surface is inclined and the retaining wall is rough, the soil pressure ' s distributing behind the panel, gets conclusion about the effect of both the slope body inner stability and the slope surface local stability to the soil pressure

    通過分析比較，論證了對數螺旋線型比圓弧形作為邊坡的假設滑裂面具有較多的工程優點，並為此編制了一個採用極限平衡法分析土釘支護的fortran語言程序，以此作工具對滑裂面的后移、土釘錨固段的超長、土釘總力的大小等方面作了研究，得出了有關土釘的長度與邊坡的坡角、坡高、土體力學參數的關系、土釘總力與庫侖土壓力間的關系等結論；採用大型通用有限元數值分析程序ansys分別對採用土釘支護的一階邊坡、二階邊坡進行分析，重點是研究各排土釘的軸力分佈規律、開挖方式及原始邊坡形態對土釘的軸力的影響、上下階邊坡在土釘軸力方面的相互作用，得出了有關第一排土釘的設計問題、不同類型的土體應適用於特定的開挖方式、原始開挖出的邊坡形態對一些類型坡體的邊坡土釘支護有較大的影響而對另外一些影響不大、二階邊坡臺階寬度的合理確定、二階開挖及支護比一階時具有較多的工程優點等結論；通過土壓力分析對朗肯、庫侖兩種經典土壓力理論的區別與聯系、坡面傾斜及墻背有摩擦時的坡面豎向應力分佈、面板背土壓力的分佈形態作了研究，得出了邊坡支擋土壓力受坡體內部穩定與坡面局部穩定兩個方面的影響、土釘支護面板背土體中卸荷拱的存在對面板受力有利等結論。
  19. Second, the thermoelastic coupling vibration of cylindrical shell are discussed by means of the same method. the coupling coefficient, amplitude of temperature, initial displacement, ratio of length to radius and that of radius to thickness are main factors which influence the thermoelastic vibration of cylindrical shell ; the higher the coupling coefficient is, the lower the axial force, the axial stress and the axial moment are

    其次，我們用同樣的方法研究了圓柱殼的非線性熱彈耦合振動，主要結論如下：影響圓柱殼非線性熱彈耦合振動的因素主要有耦合系數、溫度幅值、長徑比、徑厚比以及初始位移參數；耦合系數越大，軸向應力、軸向力以及軸向彎矩越小。
  20. The experimental results indicate that the tangent stress keeps quite linear relation with the variation of the time in fixed transmission distance of lcr wave in elastic range. also, the experiment results prove correctness and feasibility of the methods for measuring and processing lcr wave in stress measurement. the research provides beneficial reference for the application of tangent stress measurement in elastic media from theory to practice with tdc

    實驗數據表明:在試件的彈性范圍內，試件內部的切向應力與lcr波在固定傳播距離下的聲時變化有著良好的線性關系;證明了基於tdc - gp1的測試信號處理方法在用lcr波進行切向應力測量的可行性和正確性，為彈性介質中的切向應力測量從理論研究走向實踐應用提供了較高的參考價值。
分享友人
分享到 Line

分享到臉書