活塞工作面 的英文怎麼說

中文拼音 [huósègōngzuòmiàn]
活塞工作面 英文
piston face
  • 活 : Ⅰ動詞1 （生存; 有生命） live 2 [書面語]（救活） save （the life of a person）:活人無算 （of a goo...
  • 工 : Ⅰ名詞1 （工人和工人階級） worker; workman; the working class 2 （工作; 生產勞動） work; labour 3 ...
  • 面 : Ⅰ名詞1 （頭的前部; 臉） face 2 （物體的表面） surface; top 3 （外露的一層或正面） outside; the ri...
  • 活塞 : plunger; stop; bibb cock; bib（b）; [機械工程] piston; gas piston; headed piston活塞桿 piston rod...
  1. Numerical analysis of surface stress and desquamating for piston ring with chromeplating surface

    鍍鉻活塞環表面層工作應力及剝離的數值分析
  2. Designning well tube and drill - hole diameter in order to increase thickness of both annular packing gravel and water - resisting clay, nylon net packing around well tube filters, designing filter layer on the boundary between packing gravel and water - resisting clay and ramming the gravel by working the piston into the well after gravel packing completion and the filling clay for salt - water resisting etc. we succeeded in constructing 3 drinking - water wells in minqin county, proved the affectivity and feasibility of using it and giving a certain technical demonstration of construction of drinking - water well in the same similar to this area

    通過孔徑與管徑的調配設計，增大環狀粒料層和止水粘土層的厚度；濾水管外包尼龍紗網；粒料與止水粘土接觸界面上設計反濾層；填粒后先行拉活塞利用水力夯實粒料層，再投粘土球止掉上部鹹水等措施，在民勤縣三口人飲水井施工中取得顯著效果，證明了該套成井工藝的有效性和可行性，有望為同類地區人飲水井施工提供技術示範作用。
  3. This thesis presents systematic quasi - static and dynamic experimental researches on the engraving process of two pistons in solo soldier multi - purpose weapon system dzj00. on the basis of the analysis to the experimental data, a theoretical study is performed and a computing model is established. the calculating results fit well with the test results. at the same time, many affective factors have been considered

    本文對單兵多用途攻堅彈武器系統內的活塞對制動環的擠進過程進行了系統的準靜態和動態試驗研究，在通過對試驗結果的分析的基礎上，對擠進過程從理論方面進行了一些探索性的研究工作，建立了計算模型並進行了計算，其結果和試驗結果吻合較好，同時分析了多種因素對擠進過程的影響。
  4. This thesis gaved a detail account to the main part. for example : the design of the cylinder and the piston rod ; the time calculate of the valve ; the design of the disc spring and how to use it

    根據斷路器的要求進行了彈簧液壓機構的主要液壓元件的設計：集成式工作缸和變截面活塞桿結構設計；電磁閥、控制閥系統結構設計及動作時間的近似計算；儲能碟形彈簧的結構設計、應力計算及選用方法。
  5. The new unit has following technical features : ( 1 ) the unit ' s load is balanced by means of the accumulator and hydraulic cylinder with special structure ; ( 2 ) the installed power of the unit can be reduced greatly by adopting the accumulator ; ( 3 ) variable frequency speed regulation ensures good energy saving effect, and the closed oil circuit requires less hydraulic oil ; ( 4 ) a bi - directional hydraulic lock in the oil circuit ensures the stability and safety of the operation of the pumping unit

    新型機具有4個技術特點： （ 1 ）由於活塞柱塞式液壓缸的特殊結構和液壓蓄能器的配合使用，在平衡抽油機大部分載荷時，不需另外增加配重，可減小抽油機體積、質量和佔地面積； （ 2 ）抽油機下沖程時，與活塞柱塞式液壓缸相連接的蓄能器吸收能量，上沖程時儲存在蓄能器中的能量補充載荷上行所需的能量，大幅度降低抽油機裝機功率； （ 3 ）利用變頻容積調速節能效率高，閉式油路節省液壓油，同時大大減小液壓泵站的體積； （ 4 ）在閉式油路中採用雙向液壓鎖可使抽油機的啟停更加平穩、迅速，其工作的穩定性和安全性更好。
  6. ( 2 ) in the original system because of the area between the piston and the piston pole is too small, the system pressure will rise when in the return stroke. and the reliever valve will open. the return velocity will reduce

    （ 2 ）原設計中，由於活塞和活塞桿的面積差很小，回程上行時，系統壓力會迅速升高造成溢流閥的溢流而使回程速度降低，從而降低了系統的工作效率。
分享友人
分享到 Line

分享到臉書