活性燒結 的英文怎麼說

中文拼音 [huóxìngshāojiē]
活性燒結 英文
reactive sintering
  • 活 : Ⅰ動詞1 （生存; 有生命） live 2 [書面語]（救活） save （the life of a person）:活人無算 （of a goo...
  • 性 : Ⅰ名詞1 （性格） nature; character; disposition 2 （性能; 性質） property; quality 3 （性別） sex ...
  • 燒 : Ⅰ動詞1 （使東西著火） burn 2 （加熱或接觸某些化學藥品、放射性物質等使物體起變化） cook; bake; hea...
  • 結 : 結動詞（長出果實或種子） bear （fruit）; form （seed）
  • 活性 : [化學] activity; active; activated活性肥料 active fertilizer; 活性酵母 active dry yeast; 活性粘土...
  1. The formation of new phase such as mullite and gahnite by solid - phase reaction in multiphase materials can benefit the sintering of materials at 1700, decreased apparent porosity to less than 5 %. reducing atmosphere inhibited the synthesis of mullite and gahnite, played a negative role in the densification of multiphase materials

    固相反應生成的鋅鋁尖晶石和莫來石具有較高的活性，使復相材料在1700燒后顯示出更好的燒結性能，其顯氣孔率降低到5以下；還原性氣氛阻礙了莫來石和鋅鋁尖晶石的生成，不利於復相材料的燒結和緻密化。
  2. The raw materials, the composition, the time of milling, the calcining temperature, the different additives, the sintering temperature and the sintering parameters were investigated. the result showed : it was advantaged to obtain high initial permeability mnzn ferrite with stable frequency characteristic using high - purity raw materials ; in order to obtain mnzn ferrite with high properties, we must control strictly the composition ; it could improve the properties of mnzn ferrite by optimizing calcining temperature. the lower calcining temperature made the permeability higher, and the higher calcining temperature could promote the frequency characteristic of permeability ; we chosen the right time of milling according to the requirement of power diameter ; in order to improve the properties of mnzn ferrite, it is necessary to add effective additives. in this dissertation, the influence of bi2o3 、 moo3 、 k2co3 、 co2o3 were investigated ; the sintering temperature, the time of heat - retaining and sintering parameters were the key factors of preparing high permeability mnzn ferrites

    研究結果表明:採用高純度的fe2o3有利於獲得高起始磁導率且頻率特性優良的鐵氧體;為了制備所需性能的鐵氧體，需要嚴格控制配方中各種原材料的含量，優化配方;由於粉體活性受預燒條件的影響，所以對不同要求的鐵氧體選擇的預燒條件就不一樣，適當降低預燒溫度有利於獲得較高的起始磁導率，而為了獲得良好的頻率特性可以適當地提高預燒溫度;根據對粉體顆粒粒徑的不同需求，可以選擇不同的球磨時間;而有效的添加劑是改善材料性能的必要條件，本文在添加劑的研究中主要對bi2o3 、 moo3 、 k2co3 、 co2o3的影響分別作了詳細地討論;燒結溫度、保溫時間和燒結氣氛是高磁導率mnzn鐵氧體制備最關鍵的工藝，適宜的燒結工藝可以獲得理想微結構和組成，從而得到高性能的鐵氧體材料;而從材料的微結構上來看，要提高材料的截止頻率，就要適當地細化晶粒、增加晶粒內部的氣孔。
  3. Study on activation and structure performance of calcined coal gangue

    煅燒煤矸石的活性和結構性能研究
  4. The apparent activation energy of jd and ty materials are 162 - 174kj / mol and 208 - 235 kj / mol, respectively

    由線性回歸分析計算出jd材料的燒結激活能為162 174kj mol ， ty材料的燒結激活能為208 235kj mol 。
  5. The injection process parameters influencing on injection, debinding behavior and process influencing on defects, sintering influencing on shrinkage, density, mechanical properties, and stainless steel adding cu for injection molding were examined. the experiment showed that flowing property of mixing was improved other than stability with increasing temperature and paraffin ratio in binder

    用石蠟、聚乙烯、聚丙烯為添加劑，油酸為表面活性劑，組成石蠟基多組元粘結劑體系，研究注射成形工藝過程，工藝參數對成型的影響，脫脂行為和脫脂工藝對脫脂缺陷的影響，燒結工藝對收縮率、密度、力學性能的影響，以及含銅不銹鋼對不銹鋼耐蝕性的影響。
  6. However, iron powder is liable to oxidation, which will reduce the surface activities of the powder and hinder the sintering process

    但是鐵粉很容易氧化，粉末表面活性降低，妨礙燒結過程的充分進行，使實際燒結過程難以達到理想的燒結程度。
  7. Then the dehydrated and baked mixing material was calcined at 1280 to completely decompose the hydroxide in the mixing material and get powder of good sintering activity

    混合料脫水烘乾后在1280下進行煅燒，使混合料中所含氫氧化物完全分解，得到燒結活性好的粉料。
  8. Otherwise, sic can strengthen the samples by its pinpoint effect. the results also showed that the hardness of samples rise with the increase of sic, but the densities decline

    Sic的加入，增大了（ zro2 ） al2o3復合材料的硬度，但降低了材料的燒結活性，使燒結體的緻密度下降，材料的強度和韌性也有所下降。
  9. Especially, when - bi together with a little carbon black ( cb ) or copper salt is used, the catalytic effect is better ; the flame structures of the double - base propellants containing - bi are similar to the typical plateau double - base propellant, but the combustion temperature distribution has been changed because of adding the - bi ; and the active components of catalysts deposit on the burning surface of propellants and the quenched surfaces of propellants with various catalysts possess different structure

    它與銅鹽和少量炭黑（ cb ）復合后，催化效果更優； 2 ， 4 -二羥基苯甲酸鉍加入后，推進劑的火焰結構保持了典型平臺雙基推進劑的結構特徵，但改變了雙基推進劑燃燒波溫度分佈，炭黑和銅鹽的加入對2 ， 4 -二羥基苯甲酸鉍的催化作用有很大影響；催化劑分解的活性組分富集在燃燒表面，不同催化劑使推進劑熄火表面形成不同的結構。
  10. The influence of nano - al2o3 on the sintering and the properties of the si3n4 ceramics was researched in this paper. the samples with different amount of nano - al2o3 were obtained by using pressureless sintering at 1600, 1650, 1700 in the nitrogen atmosphere. the microstructure and the composition of the ceramics were determined by the means of x - ray, sem, micro - hardness meter etc. it is show that the sisty ceramics can be densified at 1650c to % percent of the theory density through the addition of nano - al2o3 ( the value could be 90 percent by other technique ). the crystalline growth of the cylindrical - si3n4 and the ratio of its longitude to its diameter are increased with the addition of nano - al2o3. a uniform microstructure and an fined crystal as well as more sialon phases can be obtained in the si3n4 ceramics through the addition of that

    實驗結果表明：在碳管爐中、氮氣保護下進行燒結，添加劑為納米al _ 2o _ 3粉末時，由於納米粉末的高活性、高燒結驅動力，在1650就可使si _ 3n _ 4完全地燒結，並使其緻密度可達理論密度的96以上（比其它工藝高6左右） ；同時，納米al _ 2o _ 3地加入大大促進了長柱狀? si _ 3n _ 4的生長和發育及柱狀晶長徑比的提高，使微觀結構均勻、細化，形成了更多力學性能優異的固體? sialon相，減少了不利於陶瓷材料性能的晶間玻璃相，凈化了晶界。
  11. The results show that high - temperature calcinations, alkaline leaching and stirring scrubbing can ' t separate the current collectors and active materials effectively

    研究結果表明焙燒法、堿浸法和攪拌擦洗法都不能達到活性物質與集流體的有效分離。
  12. The particles ’ diameter is smaller than that which be sintered by u sing common raw material

    燒結的活性物質粉體粒徑比普通原料燒結的也要小很多。
  13. Both of the two ways can reach fb5b standard of tdk company. the coercive force of strontium permagnetferrite can be improved when a12o3 or cr2o3 was added to caco3 - sio2 or caco3 - hbo3 multi - additives. ( 4 ) comparing with normal caco3 and sio2, the nano caco3 and sio2 improve the magnetic. for the nano caco3 and sio2 have high chemical activations and excellent distribution, the density of permagnetferrite can be improved and the sinter temperature of it can be reduced

    納米caco _ 3 、 sio _ 2與普通caco _ 3 、 sio _ 2加入相比，鍶鐵氧體永磁獲得的最佳磁性能高，獲得最佳磁性能的添加量范圍變寬，即納米caco _ 3 、 sio _ 2提高了磁性能的穩定性，有利於大生產時鍶鐵氧體永磁的磁性能的穩定，對生產有重要的指導四川大學碩士論文意義;由於納米caco3 、 510 :分佈更均勻，具有高的化學活性，降低了銘鐵氧體永磁的最佳燒結溫度，提高了銘鐵氧體永磁的燒結密度，因而增大了caco3 、 510 :添加劑對銘鐵氧體永磁的改性效果。
  14. The combustion conditions in a circulating fluidized bed ( cfb ) boiler are much different from a pulverized coal firing ( pf ) boiler. however, this dissertation has confirmed that coal char in cfb boiler will also experience reactivity loss and ordering of turbostratic carbon structure, which have been reported by many researchers whose work were mainly restricted to pf conditions

    本文通過獲得在cfb燃燒條件下熱解和燃燒過程中的焦碳，對其反應性、亂層碳結構、礦物質催化作用和比表面積等進行了系統研究，指出cfb鍋爐和煤粉爐同樣存在焦碳亂層碳結構有序化和焦碳反應性下降（失活）現象，並全面分析了焦碳失活的機理。
  15. In order to overcome the influence of the technology factor in active molybdenum - manganese metallization, the formulation, raw material treatment, painting method and sintering process are improved in alumina ceramics metallization, which can raise the technique level, product quality and uniform

    摘要針對影響氧化鋁陶瓷活化鉬錳法金屬化的工藝因素，在配方、原料處理、塗敷方式、燒結等方面進行改進，提高工藝水平，保證質量穩定性、一致性。
  16. Therefore, the study deashed coal, in addition to being from minerals except coal physical structure, chemical structure, soluble ion content have undergone significant changes in contrast to the ash from coal combustion or after gasification reactivity, without these changes, concludes the reliability is suspect

    因此，在研究煤粉脫灰處理后，除了礦物質被脫除外，煤粉物理結構、化學結構、可溶離子含量都發生了很大變化，在對比脫灰前後煤粉燃燒或氣化反應活性時，如果沒有考慮這些變化，得出結論的可靠性是令人懷疑的。
  17. The nanometer powder had lower sintering temperature than oxide powder because of its high surface activation and the difficulty of sintering fine material because of gas transport process predominating the sinter process

    納米粉體具有高表面活性，能在更低溫度下實現燒結，但同樣是因為高表面活性，使鋰揮發現象加劇，氣相傳質在燒結過程中佔主導地位，難以燒結出緻密材料。
  18. The properties of these doped powders, the microstructure and composition of these rare - earth co - doped tungsten matrices and cathodes have been investigated by size analysis, xrd, sem and edax. the electronic emission performances of these cathodes are measured in uhv electron emission surveyor. aes is adopted to analyze the atom composition and diffusion behavior of active elements on cathode surfaces

    通過粒度分析、 xrd 、 sem 、 edax研究了摻雜粉末的特性、燒結基體和陰極的微觀結構和成分;用動態真空電子發射測試儀對上述陰極進行了電子發射水平的測試;採用aes對陰極表面原子組成和活性物質的擴散行為進行了研究，分析了陰極發射水平與表面原子組成的關系。
  19. Ultrafine nickel powders have been used as catalysts, magnetic materials, sintered activators, electroconductive sizing materials, hard metal adhesives, etc. the research on ultrafine nickel powder is a topic of general interest in the new materials fields at present

    超細鎳粉在催化劑、磁性材料、燒結活化劑、導電漿料、電池材料、硬質合金粘結劑等方面具有廣闊的應用前景，已成為國內外新材料研究開發的熱點之一。
  20. Moreover, the sio2 / tio2 composite thin film showed the lowest pl intensity due to a decrease in the recombination rate of photo - generated electrons and holes under uv light irradiation, which further confirmed the film with the highest photocatalytic activity at 700 c. when the calcination temperature was higher than 700 c, the decrease in photocatalytic activity was due to the formation of rutile and the sintering and growth of tio2 crystallites resulting in the decrease of surface area

    同時，此時sio _ 2 / tio _ 2復合薄膜的熒光光譜顯示最低的熒光強度，這表明此時薄膜中的光生電子和空穴的復合速率最低，因而更有利於物質的光催化降解。當熱處理溫度高於700時，武漢理工大學碩士學位論文薄膜的光催化活性下降，這是由於薄膜中晶相二氧化欽的燒結和成長導致樣品的表面積下降以及金紅石相的形成。
分享友人
分享到 Line

分享到臉書