流動管反應器 的英文怎麼說

中文拼音 [liúdòngguǎnfǎnyīngqì]
流動管反應器 英文
flow-tube reactor
  • 流 : Ⅰ動1 （液體移動; 流動） flow 2 （移動不定） drift; move; wander 3 （流傳; 傳播） spread 4 （向壞...
  • 管 : Ⅰ名詞1 （管子） pipe; tube 2 （吹奏的樂器） wind musical instrument 3 （形狀似管的電器件） valve;...
  • 反 : Ⅰ名詞1 （方向相背） reverse side 2 （造反） rebellion 3 （指反革命、反動派） counterrevolutionari...
  • 應 : 應動詞1 （回答） answer; respond to; echo 2 （滿足要求） comply with; grant 3 （順應; 適應） suit...
  • 器 : 名詞1. （器具） implement; utensil; ware 2. （器官） organ 3. （度量; 才能） capacity; talent 4. （姓氏） a surname
  • 流動 : 1. （液體或氣體移動） flow; run; circulate 2. （經常變換位置） going from place to place; on the move; mobile
  1. An air straightener should be placed down stream from propeller to counteract circular air motion in the tube.

    一種氣體直線流動器應該使氣流從推進器的反作用中使氣體的活動在管內循環。
  2. Abstract : a tube reactor mixed by an axial continuous flow and four side jets as the dispersed flow is studied. the concentration distribution of the dispers ed flow was measured by means of the laser light scattering. the different flow patterns revealed the special construction of concentration distributions in relation with the velocity ratio of side flow and axial flow

    文摘:研究了圓管反應器中四束側向對撞射流與軸向流形成的混合流動.應用激光粒子散射成像測量了側向分散相在混合流中的濃度場分佈，得到了不同的濃度分布圖形隨側向流與軸向流速比關系，揭示了內在有規律的獨特的濃度分佈結構
  3. A novel model for residual fluid catalytic cracking process ( rfcc ) is proposed. it divides the whole reactor into two part : the riser as ideal pipe flow reactor and the sett - ler as ideal cstr. the model contains six lumps reaction kinetics with serial and parallel network

    通過將實際裝置中發生裂化反應的提升管和沉降段反應器分別考慮為理想的活塞流反應器和連續攪拌式反應器，建立了簡化的渣油催化裂化反應6集總組分的串列和并行反應動力學網路模型。
  4. In this paper, simple reacting flow model in solid - propellant ducted rocket combustor based on eddy break - up model is established. the model is used to simulate the three - dimensional combustion flowfields in an experimental motor. some factors how to affect the combustion efficiency are discussed in the paper, including air intake and gas generator nozzle

    本文基於簡單反應的旋渦分裂模型，建立了固體火箭沖壓發動機補燃室內的湍流燃燒模型，並在該模型下對某實驗發動機進行了三維數值模擬，研究了補燃室設計參數包括進氣道出口設計參數和燃氣發生器噴管設計參數對燃燒效率的影響。
  5. Simulating results reveal that hydrodynamics of catalysts in riser reactor is very complex due to the effect of injection and catalysts backmix dramatically near the nozzle, reaction products unevenly distributie along the riser height, there exists apparently temperature gap between gas - phase and solid - phase near the nozzle and the temperture of two phase is nearly equal at middle - top part

    模擬結果表明，由於原料油射流的影響，提升管反應器內催化劑顆粒的流動特徵非常復雜，在噴嘴附近的催化劑顆粒存在明顯的滑落返混；裂化產物濃度沿提升管存在非均勻分佈；氣粒兩相間溫差在噴嘴附近顯著，在中上部氣粒兩相溫度幾乎相等。
  6. From this work, a new way to improve the fluidization quality of the ultra - fine powders is found, and the studying result can supply as a basis of further investigation and be able to be used in the design of a spouted bed with a draft tube for the ultra - fine powders

    本研究為改善超細粉的流化質量提供了一種新的思路，研究成果為進一步四川大學碩士學位論文開展有關基礎研究和開發超細粉導向管噴動床反應器提供了良好的基礎。
  7. Local flow characteristics in the riser of an external - loop airlift reactor

    氣升式外環流反應器上升管中局部流動特徵
分享友人
分享到 Line

分享到臉書