流面 的英文怎麼說

中文拼音 [liúmiàn]
流面 英文
flow plane
  • 流 : Ⅰ動1 （液體移動; 流動） flow 2 （移動不定） drift; move; wander 3 （流傳; 傳播） spread 4 （向壞...
  • 面 : Ⅰ名詞1 （頭的前部; 臉） face 2 （物體的表面） surface; top 3 （外露的一層或正面） outside; the ri...
  1. Abstract : the paper introduces a kind of method of connecting optimal design of the hydraulic manifolds and establishes the mathematical model based on the constraints of fluxing area and distance between the connecting tubes in the manifolds. a kind of algorithm is provided at the end of it

    文摘:介紹了一種液壓集成塊孔道優化設計方案，建立了以通流面積和壁厚為約束條件的數學模型，並給出了相應的演算法。
  2. The upper of the east model boundary remains constant head and the at the lower of it, there might exists a diffluent interface. so the east and west sides of the diffluent interface are respectively the drainage area of east and west karst - groundwater of yellow river

    模型東界上部以黃河水位為第一類水頭已知邊界，下部必存在一個分流面，分流面東西兩側分別是黃河東西兩塊巖溶水的排泄區，該分流面可視為零流量邊界。
  3. The calculation method of ln ( / tan # ) index widely used is the multiple flow direction algorithm developed by quinn et al. it can been seen that, in the algorithm, the contour length normal to the direction of flow flowing out the current cell is used to determine both a and tan #, and that the calculated total cumulative contributing area of downslide grid cell does not include the area of the current cell

    目前普遍使用的計算該地形指數的方法為多流向法。方法中計算和tan用的均是與流出單元網格流向垂直的等高線長。另外計算下坡單元網格累積匯流面積時沒有考慮欲計算ln （ tan ）值的單元網格的面積，這些是不合理的。
  4. Many researches have been done with the simulation model. it was found that some structure parameters such as the diameter of the driving piston, the diameter of the buffer piston, the stiffness of the valve spring, the compress ratio of the buffer piston, and the flux area of the solenoid valve etc. have great effect on the performance of the haecvvs. for certain performance demand of the variable vale system, there is a most suitable combination for the structure parameters

    通過對電控可變氣門系統的主要結構參數，如動力活塞直徑、緩沖活塞直徑、氣門彈簧剛度、緩沖活塞實際壓縮比、電磁閥通流面積等參中壓共軌電控柴油機可變氣門系統的研究數對電控可變氣門系統啟、閉特性的影響規律的研究發現，動力活塞直徑、氣門彈簧剛度、電磁閥通流面積對電控可變氣門系統啟、閉性能起著決定性的作用，對於一定的氣門啟閉規律要求，這些結構參數存在一組最佳值。
  5. The main research outcomes were as follows : ( 1 ) the paper applied quasi - three dimensional design model and optimization design model based on si flow surface that was effected by runner ( impeller ) and guide vane jointly. the vortex flow, blade thickness limitation and runner ( impeller ) blade force functions were taken into account. the paper got the improved runners of hl240 type, which were runner hlx240d and runner hlx240e

    主要成果有： （ 1 ）應用考慮轉輪來流有旋、葉片有限厚及轉輪（葉輪）葉片力作用的轉輪（葉輪）與導葉聯合作用的基於s _ 1流面的準三維設計模型和優化設計模型，研究出了hl240的改進型轉輪： hlx240d和hlx240e 。
  6. Surface religion games - 4455 miniclip games

    流面道場小游戲- 4399小游戲
  7. Abstract : based on the result of visioplasticity test, the law of tube central upsetting was created, and the calculated method of displacement field and strain field were obtained. in this study, the four deformation modes were showed when ratio of height to thickness of tubular billet is greater than 3. the four modes were related to the distribution of strainless - plane

    文摘:根據管坯視塑性實驗法的實驗結果，分析了無芯軸支撐條件下，管坯中部鐓鍛的變形規律，闡述了變形區位移場、應變場的計算方法；通過對實驗結果的分析，得出了當鐓粗比3 ，管坯中部鐓鍛時，內壁呈現四種典型的變形模式；論述了分流面的分佈與四種變形模式之間的轉化關系。
  8. Sc - source : what role do you play in the chain of communication between the community and the development team

    你在溝通網路社區和開發團隊方的信息交流面扮演怎樣的角色？
  9. Analysis of two typical sorts of velocity gradient equations about s

    2流面的兩類典型梯度方程的分析
  10. Surface religion introduction

    流面道場游戲攻略
  11. Experimental study on united energy dissipator with grid and stepped spillway

    格柵與階梯式溢流面聯合消能工的試驗研究
  12. Hypnosis jump goat games

    流面道場小游戲
  13. Everybody fault games

    流面道場小游戲
  14. Planar flow structure

    流面構造
  15. Cause analysis and control of fangguanying reservoir dam upstream slope prevention destruction

    察爾森水庫護坡灌漿和溢流面混凝土修補
  16. But it is thought that the mature pump inner flow numeric computation was started and then developed rapidly after the " two relative flow surface " ( the s1 and s2 ) theory presented by professor wuzhonghua

    但具有完備形態的內流數值模擬，一般認為始於吳仲華教授的s1 、 s2兩類相對流面理論后，葉輪機械內流數值模擬才得到了迅速發展。
  17. In the thesis, the design method of the diagonal flow fan impeller has detailedly researched different from the previous means borrowing and extending design methods for axial flow or centrifugal type, a complete design method has presented on the basis of quasi - three dimensional design idea. the course is mainly composed of such steps as meridional surface design, inverse problem computation in meridional surface, blade shaping on stream surface, and verifying through three dimensional computation, until the design requirement is met at last

    不同於以往的軸流式或離心式延長設計方法或經驗方法，本文按照準三元設計的思路給出了一套完整的設計方法，即子午面設計?子午面反問題計算?斜流流面上葉片造型?三維計算驗證優化，直至符合設計目標。
  18. According to theoretical analysis and experiments on the throttle control system, the quantitative relationship among the speed of executive element, the flow area of the throttle and the load is determined

    本文通過對進油路節流調速系統的理論分析與試驗研究，闡明了執行元件的運行速度與節流閥的通流面積以及負載之間的定量關系。
  19. Abstract : according to theoretical analysis and experiments on the throttle control system, the quantitative relationship among the speed of executive element, the flow area of the throttle and the load is determined

    文摘:本文通過對進油路節流調速系統的理論分析與試驗研究，闡明了執行元件的運行速度與節流閥的通流面積以及負載之間的定量關系。
  20. The power is decreased when the fouling in the steam path of steam turbines is formed

    汽輪機通流部分結垢將使通流面積減少，使機組出力下降。
分享友人
分享到 Line

分享到臉書