浮壓成形 的英文怎麼說
中文拼音 [fúyāchéngxíng]
浮壓成形
英文
embossing-
With this purpose, this paper researches the state of dometic and overseas seal technique ; uses other enterprise ' s successful experiments for reference ; combines the factory set ' s structural property, technics characteristic and the different request of medium leakage degree ; considers the respective strongpoints of floating ring seal, conical floating seal, suction labyrinth seal, inflator labyrinth seal, mechanical seal, dry gas seal ; finds out the optimum, dependable seal techinique fiting for each set on the base of entire analysis on the centrifugal compressor. and in the end by putting this plan into practice the factory achieves localized reconstructs, reduces the production cost and fulfils the demands of secular safe use
本文在把握國內外離心壓縮機密封技術的發展狀況，借鑒其他企業的成功經驗基礎上，根據我廠機組結構特性、工藝特性、介質泄漏程度要求的不同，以及浮環密封、錐形浮環密封、抽充氣式迷宮密封、機械密封、干氣密封的各自特點，對離心壓縮機存在的密封問題進行了全面剖析，研究了適合每臺機組最佳、可靠的密封技術，實施了本地化技術改造，降低了生產成本，滿足了機組長期穩定運行的生產要求，取得了顯著的經濟效益和社會效益。Smooth tempered glass is manufactured by heating up float glass to swiftly and uniformly, with this special heat treatment and quenching process which increases glass strength up to four to five times vs, annealed glass, in case stresses beyond its capacity, smooth tempered glass simply disintegrates into innumerable small pieces, significantly reducing the risk of serious injury
鋼化玻璃是將浮法玻璃經過物理性淬火處理，使其表面形成均勻的壓應力，而內部則形成張應力，從而有效的提高了玻璃的抗彎和抗沖擊性能，強度達到了普通玻璃的3 - 4倍，當其破碎時則分裂成均勻純角不易傷人的小顆粒，使其成為一種現代生活中理想的安全玻璃。In the past, many experts on cotton spinning wished to combine the nitto model drafting technics of little proparea gauge, small flotation area and strong controlling with the drafting model pressurized by cradle, feasible results still having not been achieved
過去曾有許多棉紡專家希望把日東式牽伸的前區小隔距、小浮遊區、強控制的牽伸工藝與搖架加壓的牽伸形式相結合，但一直沒有可行的成果面世。As the ice forms and expands, causing a buildup of pressure, the 800m4fr relieves the pressure through a unique relief valve built into the plastic float
當冰開始形成並擴張時，會產生壓力累積， 800m4fr系列就會通過內置塑料浮子的獨特的安全閥釋放壓力。Dissolved air floatation is that air is dissolved under pressure is the liquid which is then released to atmospheric pressure in tube. as the microscopic air bubbles come out of solution in cell, they attach to the suspended solids in the surface in liquid, causing them to floatation th the surface, then solids are separated from liquid
氣浮就是設法在待處理液體中通入或產生大量密集的帶有壓力的微細氣泡，在管道以常壓下釋放，使其在池內與雜質，絮粒互相粘附形成整體浮體，從而依靠浮力使其上浮至液面，從完成固液分離的方法Characteristics, application of laser surface non - consolidation process in dies, development and research status of such process domestic and abroad as well as problems and trendency of dies surface reinforced treatment by laser have been introduced
分析了兩端對稱類零件在單向加壓設備上成形時兩端變形程度不同的原因，介紹了採用浮動模結構來解決這一問題的方法。分享友人