浮沉材 的英文怎麼說

中文拼音 [fúchéncái]
浮沉材 英文
bobber
  • 浮 : Ⅰ動詞1 （漂在液體表面） float; drift 2 [方言] （在水裡游） swim Ⅱ形容詞1 （在表面上的） superfici...
  • 沉 : Ⅰ動詞1 （沉沒; 墜落） sink 2 （沉下 多指抽象事物） keep down; lower 3 [方言] （停止） rest Ⅱ形容...
  • 材 : 名詞1 （木料） timber 2 （泛指可以直接製成成品的東西; 材料） material 3 （供寫作或參考的資料） ma...
  • 浮沉 : now sink, now emerge; be unstable or uncertain; drift along; oscillate
  1. In the study of the lumber carrier, one of the very important problem is the in spot and ultimate station due to flooding which will bring tremendous threat to the ship because of the few holds in order to study the lumber carrier buoyancy, stability and longitudinal strength under the condition of flooding, the paper adopt fundamental ship principle and iterative and accumulative concept on the basis of insumersibility theory to detailedly calculate the flooding speed flooding amount front draft after draft stability and longitudinal strength considering the ship " s sinking and inclination which will change the center of gravity and the loading station both in hold and on deck and the effect of flooding and lumber amount in holdo in the last, the paper introduces an example of the actual ship named " fei yun ling " and makes a contrast between not taking measure and taking measure which draws a reasonable conclusion and comes up to some advice the method avoids the cockamamie calculating while insures enough precision the paper draws a conclusion that not all the lumber carrier will submerge when suffering the damaged flooding if the loading or measure is suitable

    為了研究運木船舶在破艙狀態下的浮性、穩性和強度，本文在抗沉性理論的基礎上，運用船舶基本原理，採用了迭代和累計的思想，將船舶的進水過程劃分為很多次進水的積累，詳細計算了運木船在破艙進水的過程中，考慮到各種破艙參數、船舶本身的下沉、艙室內木材、甲板貨的裝載情況和在進水過程中船舶本身的傾斜對進水重心的影響，以及艙室內的進水量和木材對破口處進水速度的影響，船舶總的進水速度、進水量、首尾吃水、穩性的實時狀態和最終船舶的總縱強度，給出了計算實例，並進行了在採取用泵抽水前後浮態參數的對比，得出了該船舶在艙室內的貨物積載量達到某個數值時可以保證船舶在破艙進水時不會沉沒，或者在當開口小於某數值時，採取適當的措施后，可以使船舶避免沉沒。
  2. The experimental techniques ( such as sedimentation equipment, controlling the size and size distribution of powders, the concentration of suspension ) have been devised subtly. on the basis of theoretical and densification design, the w - mo - ti fgm has been obtained by particle settling and hot pressing sintering. the structures of specimen were observed by electron probe

    通過對實驗工藝，如沉降設備、原料粒度及粒度分佈的控制、懸浮液濃度等方面進行精細的設計，在理論設計和緻密化研究的基礎上，通過顆粒共沉降得到梯度沉積體，並通過真空熱壓燒結得到w - mo - ti功能梯度材料。
分享友人
分享到 Line

分享到臉書