浸漬塗層 的英文怎麼說

中文拼音 [jìnzìtúcéng]
浸漬塗層 英文
dip coating
  • 浸 : Ⅰ動詞1 （泡在液體里） soak; steep; immerse 2 （液體滲入） soak; saturate; steep Ⅱ副詞[書面語] （...
  • 漬 : Ⅰ名詞1 （地面的積水） floodwater on low lying land 2 [方言] （積在物體上難以除去的油泥等） stain;...
  • 塗 : Ⅰ動詞1 （抹） spread on; apply; smear 2 （亂寫或亂畫） scrawl; scribble 3 （抹去） cross [blot; s...
  • 層 : i 量詞1 （用於重疊、積累的東西 如樓層、階層、地層） storey; tier; stratum 2 （用於可以分項分步的...
  • 塗層 : paint-coat; paintcoat; coat; coating; covering; lining; wrapping flux
  1. It is processed by fibreboard of middle density to conglutinate paper dipped with melamine, treated with aluminum trioxide coating

    系用中密度纖維板粘貼三聚氫氨浸漬紙，並經三氧化二鋁塗層處理製成。
  2. Standard practice for testing water resistance of coatings using water immersion

    水浸漬法測試塗層的耐水性能的標準實施規程
  3. The sca film is formed on stainless steel plate through dipping - draught method, and drying in 80 c in an hour

    以浸漬提拉法在不銹鋼表面施塗膜層，在80下烘乾一小時，制得摻銀有機硅烷抗菌不銹鋼。
  4. Focusing on serious damage of carbon fibers in ceramic matrix composites ( cmcs ) prepared by precursor infiltration pyrolysis ( pip ), and with emphasis on carbon fiber reinforced silicon carbide composites ( cf / sic ) derived from polycarbosilane ( pcs ), the influences of raw materials ( including carbon fibers and precursors, etc. ) and preparing conditions on carbon fiber damage during the preparation of cf / sic composites were investigated systemically. pyrolysis process, fiber - matrix interface and carbon fiber damage process were observed by sem, tem, ir, xrd, xps and tq etc. the characterization method of carbon fiber damage degree was established and the models for carbon fiber damage mechanism were also established. the carbon fiber coatings and unidirectional cf / sic composites with coated carbon fibers were prepared and studied

    本文針對先驅體浸漬裂解工藝制備陶瓷基復合材料過程中碳纖維損傷嚴重的問題，以聚碳硅烷（ pcs ）制備cf / sic復合材料為重點，採用sem 、 tem 、 ir 、 xrd 、 xps 、 tg等表徵手段，分析了先驅體裂解過程、纖維基體界面和碳纖維損傷過程，系統地研究了原料（碳纖維、先驅體等）和制備工藝條件等在cf / sic復合材料制備過程中對碳纖維損傷的影響，建立了碳纖維損傷程度的表徵方法和損傷機理模型，制備了纖維表面塗層並利用塗層碳纖維制備了單向cf / sic復合材料。
  5. The inorganic film is formed on stainless steel plate through dipping - draught method, and under the dropping rate 10cm / min

    以浸漬提拉法在不銹鋼基板表面施塗膜層，提拉速度10cm min 。
分享友人
分享到 Line

分享到臉書