浸漬工藝 的英文怎麼說

中文拼音 [jìnzìgōngyì]
浸漬工藝 英文
dipping processes
  • 浸 : Ⅰ動詞1 （泡在液體里） soak; steep; immerse 2 （液體滲入） soak; saturate; steep Ⅱ副詞[書面語] （...
  • 漬 : Ⅰ名詞1 （地面的積水） floodwater on low lying land 2 [方言] （積在物體上難以除去的油泥等） stain;...
  • 工 : Ⅰ名詞1 （工人和工人階級） worker; workman; the working class 2 （工作; 生產勞動） work; labour 3 ...
  • 藝 : Ⅰ名詞1 （技能; 技術） skill 2 （藝術） art 3 [書面語] （準則） norm; standard; criterion4 [書面語...
  1. This paper introduces the property requirements on insulating varnish and some technical indicators of import varnishes used in electronic transformer, discusses the effects of baking temperature, baking time, dry capability, impregnation process of varnish on the noise, rustiness box craze, insulating tape bond failure which occurred in electronic transformer

    摘要介紹了電子變壓器用絕緣浸漬漆的性能要求，介紹了一些進口絕緣浸漬漆的性能指標，分析討論了漆的烘烤溫度、時間、乾燥性、浸漬工藝對電子變壓器的噪聲、生銹、外殼爆裂、絕緣膠帶脫開的影響，討論了絕緣漆在應用中的環保問題。
  2. The strength and wear resistance of diamond drill bits for petroleum exploitation will be increased considerably when cast tungsten carbide is applied and adheres to the substrate firmly with cast tungsten carbide of 80 - 200mesh as the skelton and copper alloy as the soldering material in a process of non - pressure immersion

    石油鉆探行業用的金剛石鉆頭，用粒度為80 ? 200目的鑄造碳化鎢粉作骨架，採用無壓浸漬工藝，以銅合金作釬焊料，將鑄造碳化鎢與基體牢固結合，強度、耐磨性大大提高。
  3. By determining technological parameters of epoxy insulation parts impregnated by 7122 - 1b - f electric varnish, technological process and analysis method of orthogonal test design are presented in this paper

    本文通過確定7122 - 1b - f絕緣漆浸漬環氧絕緣零件的工藝參數，介紹了正交試驗設計的工作流程和分析方法。
  4. The graphitized cathode block samples have been trial - produced using high quality eca ( electrically calcined anthracite ) rationed petroleum coke and pitch coke and quantitative pitch used as raw materials by the conventional carbon technics concluding moulding, baking, high pressure impregmating, after - baking and graphitization

    摘要選取優質電煅無煙煤，分別配以一定比例的石油焦和瀝青焦作為骨料，與煤瀝青混合后按照模壓成型、焙燒、高壓浸漬、二次焙燒和石墨化等常規炭素製品生產工藝流程制備石墨化陰極材料試樣。
  5. Liquid - solid extrusion of composite material is a new kind of metal forming process, which has been developed in recent years with a promising practical application prospect for its simple working procedure, low cost and good workpiece performance. through a lot of experiments, the optimization and chosing method of key process parameters ( pouring temperature, mold warm - up temperature, impregnating pressure, impregnating time ) has been mastered. under the precondition of appropriate chosing these parameters, the effective control of extrusion velocity is the key of mading good workpiece. but the control of extrusion velocity remains a handwork, and it is heavily affected by such uncertainties as a handler ' s knowledge and skill about the process. in order to solve the problem, the automatic control of the extrusion velocity is studied, and a computer control system is also designed under existing condition

    通過大量實驗，已掌握了關鍵工藝參數（熔液澆注溫度、擠壓模預熱溫度、浸漬時間、浸漬力）的優化選取方法。在合理選取關鍵工藝參數的前提下，擠壓速度的控制是成形出質量良好製件的關鍵。但是，目前對于擠壓速度的控制仍停留在手動控制階段，利用該工藝制備管、棒材製件的成功與否受操作者對該工藝及其設備的經驗及熟練程度等不確定因素影響很大。
  6. To simplity and improve the tedious technological process, a new process is proposed to integrate well the heating and drying with impregnation in a vacuum tank

    一體式的真空乾燥及真空壓力浸漬工藝將上述兩道工藝合二為一，在同一臺真空罐內進行一體式的加熱、真空乾燥和真空壓力浸漬。
  7. Outdoor landscape wood structure facilities, the antiseptic impregnated wood, charred wood and other horticultural timber and paving materials, wooden houses, flower racks, barriers, platform, pavilions, fences, furniture, tools house, and other products

    戶外園林景觀木結構設施，防腐浸漬木炭化木等園藝類木材及鋪裝材料，木屋花架護欄地臺亭籬笆桌椅工具房等成品
  8. Based on the infrared anomalous dispersion of compact alumina film, the character of alumina sols and the processing for fabricating compact alumina film were studied by using sol - gel method, combining dip - dropping, spin - coating method and electrophoretic deposition techniques

    本文基於緻密氧化鋁膜的紅外反常色散特性，結合溶膠-凝膠技術，採用浸漬提拉法、旋覆法和電泳沉積工藝，對氧化鋁溶膠的性質和緻密氧化鋁膜的制備工藝進行了研究。
  9. Spcc has a strong engineer team products with logical design - ing and advanced craft, scientific managerial approach and complete testing system. the key manufacturing process is finished in depur - ation workshop with constant temperature and humidity. the vacuum and temperature of disposal of vacuum impregnating is controlled by computer completely

    企業技術力量雄厚，產品設計合理，工藝先進，管理科學，測試手段全完善關鍵工序的生產過程在恆溫恆濕的超潔凈室內進行真空浸漬工藝的真空度及溫度由計算機全自動控制。
  10. Shangyu power capacitor co., ltd is an appointed manufactory for power capacitor by ministry of mechanical building, and is also one of the first batch of recommendation products manufactory list for the construction and reform of city countryside powergrid in china. spcc is located in shangyu city of advantaged yangtze river delta with ningbo adjoined in the east, hangzhou in the west, wenzhou in the south and hangzhou bay in the north. spcc has a strong engineer team products with logical designing and advanced craft, scientific managerial approach and complete testing system

    公司位於中國長三角東南翼的上虞市。東鄰寧波西毗杭州南接溫州北瀕杭州灣，地理位置得天獨厚。公司技術力量雄厚，產品設計合理工藝先進管理科學測試手段全完善關鍵工序的生產過程在恆溫恆濕的超潔凈室內進行真空乾燥浸漬全過程的真空度及溫度由計算機自動控制。
  11. The parameters of impregnation are as follows : ph is about 3, the range of temperature is from 20 to 45, and the time is about 2 to 6 hours. after the necessary treatments, zirconia cloths had the optimal strength when the diameters of zirconia fibers were controlled in 4um to 7um, and the sizes of zirconia grains were in 50nm to 100nm. the affec - ting factors were discussed and the liner regression analysis of the cloths was made, from w hich they show that the diameters and grain sizes have the significant influences on zirconia cloths. the obtained zirconia cloths have been accepted for use in nickel - hydrogen batteries by practical use

    研究結果表明：粘膠類纖維布最適合制備氧化鋯纖維布的前軀體；鋯液濃度以飽和溶液為宜；浸漬工藝參數為ph值3左右，溫度20 45 ，時間2 6小時；多餘鋯鹽的去除、浸鋯液后纖維布的整平處理及平燒施應力燒成有利於氧化鋯纖維布的柔軟及平整; 200 600燒成溫度段應緩慢燒成，控制氧化鋯纖維直徑在4 7 m ，氧化鋯晶粒尺寸50 100nm時氧化鋯纖維布的強度最好。
  12. The effect of composition of coating solution, dipping time and other technical parameters for preparation of sensors on sensing behaviour has also been described and discussed

    討論了溶液組成，浸漬時間等元件制備工藝參數對響應特性的影響。發現電極結構對于元件響應特性有一定影響。
  13. This paper describes the procedure and properties of vacuum pressure impregnating （ vpi ） process

    本論文介紹了真空壓力浸漬絕緣處理工藝的流程及特點。
  14. Conventionally the power capacitors were manufactured the way their wound cores should be heated and dried in a vacuum drying vessel first, and the cores should be pressed into capacitor shells, then all the unfinished capacitors were put into a vacuum pressure tank for inpregnation

    摘要傳統的電力電容器的生產工藝是將芯體元件卷繞后，先在真空乾燥罐內進行加熱和真空乾燥，然後將芯體元件壓裝到電容器殼內，再在另一臺真空壓力浸漬罐內進行真空壓力浸漬。
  15. A fortran code was developed based on the models, and it can be used to simulate both infiltration of resin into a textile perform and cure of the resin saturated perform

    本文用fortran語言編寫了rfi工藝過程的模擬程序，該程序可以用來模擬樹脂對纖維預製件的浸漬過程和浸漬充模完成後整個構件的固化過程。
  16. Rift resin infusion under flexible tooling

    撓性上模具樹脂浸漬工藝
  17. The microstructures of precursor fibers, fibrous cloths, the composition of zirconia solution, the technological parameters of impregnation, and the modes of drying and firing were investigated

    對前軀體纖維、纖維布結構、鋯液配方、浸漬工藝參數、乾燥及燒成方式和制度進行了深入研究。
  18. The hot - melt impregnation process of large tow carbon fiber ( 60k ) prepreg to prepare fishing rods is briefly introduced in this paper ; in addition, several typical factors which affect the quality of the prepreg are also discussed in detail here

    摘要本文簡要介紹了釣魚竿用大絲束（ 60k ）碳纖維預浸料熔膠膜法浸漬工藝，並著重就影響預浸料質量的幾個主要因素進行了討論。
  19. It is widely used in industries of food, chemical, medicine, textile for vacuum vaporizing, concentrating, macerating, drying processes

    廣泛用於食品、紡織、醫藥、化工等行業的真空蒸發、濃縮、浸漬、乾燥等工藝過程中。
  20. Focusing on serious damage of carbon fibers in ceramic matrix composites ( cmcs ) prepared by precursor infiltration pyrolysis ( pip ), and with emphasis on carbon fiber reinforced silicon carbide composites ( cf / sic ) derived from polycarbosilane ( pcs ), the influences of raw materials ( including carbon fibers and precursors, etc. ) and preparing conditions on carbon fiber damage during the preparation of cf / sic composites were investigated systemically. pyrolysis process, fiber - matrix interface and carbon fiber damage process were observed by sem, tem, ir, xrd, xps and tq etc. the characterization method of carbon fiber damage degree was established and the models for carbon fiber damage mechanism were also established. the carbon fiber coatings and unidirectional cf / sic composites with coated carbon fibers were prepared and studied

    本文針對先驅體浸漬裂解工藝制備陶瓷基復合材料過程中碳纖維損傷嚴重的問題，以聚碳硅烷（ pcs ）制備cf / sic復合材料為重點，採用sem 、 tem 、 ir 、 xrd 、 xps 、 tg等表徵手段，分析了先驅體裂解過程、纖維基體界面和碳纖維損傷過程，系統地研究了原料（碳纖維、先驅體等）和制備工藝條件等在cf / sic復合材料制備過程中對碳纖維損傷的影響，建立了碳纖維損傷程度的表徵方法和損傷機理模型，制備了纖維表面塗層並利用塗層碳纖維制備了單向cf / sic復合材料。
分享友人
分享到 Line

分享到臉書