液位控制器 的英文怎麼說

中文拼音 [yèwèikòngzhìqì]
液位控制器 英文
fluid level controller
  • 液 : 名詞（液體） liquid; fluid; juice
  • 位 : Ⅰ名詞1 （所在或所佔的地方） place; location 2 （職位; 地位） position; post; status 3 （特指皇帝...
  • 控 : 動詞1 （告發;控告） accuse; charge 2 （控制） control; dominate 3 （使容器口兒朝下 讓裏面的液體慢...
  • 制 : Ⅰ動詞1 （製造） make; manufacture 2 （擬訂; 規定） draw up; establish 3 （用強力約束; 限定; 管束...
  • 器 : 名詞1. （器具） implement; utensil; ware 2. （器官） organ 3. （度量; 才能） capacity; talent 4. （姓氏） a surname
  • 控制器 : controller; regulator; monitor; pilot; keyer; manipulator; control unit; control device; [自動化]...
  • 控制 : control; dominate; regulate; govern; manage; check; cybernate; manipulate; encraty; rule; rein; c...
  1. Condensate receiver tank ( e1183 ) collect the condensate from acc and drain pot, and the condensate will be pump to deaerate through condensate pump, and the condensate level controled by the level transmeter ( lt450 ) and switch ( ls451, ls452 )

    凝結水回收箱（ e1183 ）收集空氣冷凝器及集液箱中的中的凝結水，其中的凝結水由液位變送器（ lt450 ）及液位開關（ ls451 ， ls452 ）對凝結水泵（它方供貨）的電機（它方供貨）進行控制，凝結水被送到除氧器。
  2. The result indicates that the parameters self - adjusting illegibility controller is of well self - adaptability at the system of boiler inside wall water level control system

    結果表明，在鍋爐液位控制系統中，參數自調整模糊控制器具有良好的自適應性。
  3. In the hardware design, the paper completes modules ’ design like outside memory, patulous a / d, patulous d / a, rs232 communication, ecan communication, led control, keyboard control, distant control, emulation, reset, logic voltage switch, dsp supply power regulate and ac - dc power circuit, as well as room layout design like anterior panel, back panel etc. and dsp transfers data with peripheral equipments except outside memory using serial ports. besides, the whole circuit is configured in interrupt response. thus, it can meet system demand as well as take full advantage of tms320f2812 ’ s hardware resource. in the software design, the paper finishs programs like the interface programms intercommunicates with people, the distant control program, ad and da modules ’ control program, in addition, the paper select the velocity and acceleration state - feedback algorithm and is written in the program. the software design uses dsp integrate exploiting environment named ccs2. 2 of ti inc. as software instrument, and programs with the combination of c language and assembly language. moreover, in order to maintenance or modify the software expediently and shorten software ’ s exploitation time, the design adopt software modularization technique. finally, some air cylinder experiments are carried out to proved that the pneumatic controller is very practical

    在硬體設計中，本文完成了片外存儲器擴展、 a / d擴展、 d / a擴展、 rs232通信介面、 ecan通信總線介面、液晶顯示控制、鍵盤控制、遠程控制、模擬、復位、邏輯電平轉換、 dsp工作電源校正電路和ac - dc電源等模塊設計以及控制器前面板、後面板等的空間布局設計。其中dsp與除外部存儲器的外圍設備之間的數據傳送全部採用串口通信，同時系統電路配置成中斷響應方式，這樣既滿足了系統要求，又充分利用了tms320f2812的硬體資源。在軟體設計中，本文完成了人機界面功能模塊、遠程控制模塊、 ad擴展模塊、 da擴展模塊、速度和加速度狀態反饋的控制演算法的程序設計。
  4. Our factory mainly manufactures hydraulicfllfers, filter oil vehicles, hydraulic air cleaner, liquidlevel gage and liquid thermometer, liquid level control relay, switch of manometer, combined sealing washer, piezometer soft tebe assembly, andso on. we also carry on all kinds of non - standard, and bring in filters, air cleaner, liquid - level gage and liquid thermometer and complete set of design and manufacture of hydraulic system

    本廠主要生產各類液壓過濾器、濾油車、液壓空氣濾清器、液位液溫計、液位控制繼電器、壓力表開關、組合密封墊圈、測壓軟管總成、塑料管夾等產品，還承接各類非標、引進過濾器、空氣濾清器、液位溫計及成套液壓系統設計與製造。
  5. The control system of mould level is crucial to improve the slab quality in the continuous casting process, pid controller is used in the traditional mould level control, and it has some defaults, such as : at the start - up or finishing period of casting or during the changeover of tundish, pid control has a bad effect, its overshoot is large and its transient time is long ; the erosion of the tundish stopper and the submersed nozzles lead to the accuracy of control become bad ; the abrupt falloff of block in the submersed nozzles makes the level acutely fluctuate, and pid control can not overcome the disturbances resulted from the change of casting speed

    結晶器液位控制系統是提高連鑄產品質量的關鍵環節，傳統的連鑄機液位控制方法採用常規的pid控制，存在如下不足：開始、結束澆注和換中間罐澆注時，控制效果差，超調量大，過渡時間長；塞棒頭和浸入式水口被腐蝕后引起控制精度差；浸入式水口堵塞物的突然脫落所引起的液位劇烈波動；無法克服拉速波動引起的擾動。
  6. To the level control problem of a spherical tank, two model - free control methods are proposed. in the former method, the takagi - sugeno fuzzy model is used to tune the neuron controller gain. in the latter method, the model - free control method using the neural network model proposed for nonlinear plants is presented

    針對具有非線性特性的球形容器液位受控對象，從增益自調整和非線性補償兩個角度，分別提出了兩種非模型控制方法，前者採用t - s模糊模型對神經元控制器的增益進行在線整定，後者使用本文建立的非線性神經元網路對球形容器進行非模型控制。
  7. Comparing and analyzing the synchronous control strategy, which brings up the new method to control the double un - symmetry jars proceed synchronously with the combination of proportional valve and servo valve, which forms closed loop control ; basing on the above methods, models are made to get mathematics models of position control system and to analyze system model theoretically by using pid controller, we can realize regulating parameters, minimizing synchronous errors and enhancing the dynamic performances ; the simulink tool box in matlab software is used to imitate the system according to the model, which not only makes the result visual and easy to adjust the parameters in interactive way but also lets us understand the effects of different parameters and optimizes the dynamic properties. the theory of plc control in dshp is discussed after advanced understanding of the system movements. hardware design and general regulation are given on the base of siemens company products s7 - 200 plc

    本文根據大量的國內外文獻，對研配液壓機的工作原理及設計結構進行了簡介；對位置同步的控制方法進行了比較分析，提出比例閥和伺服閥復合控制的閉環結構來對非對稱雙缸進行同步控制電液比例同步控制方案；在此基礎上著重對比例閥控非對稱缸建模，最後得到位置控制系統的總體數學模型，從理論上對同步系統動態特性進行了分析，並用pid控制器進行參數整定，減小雙缸同步誤差、提高系統的動態響應性能；其中控制性能的分析藉助于matlab軟體中的simulink工具箱，由已建立的數學模型形成模擬模型，得到可視化的模擬結果，從而利於交互方式下調整參數，了解不同的參數對系統的影響，優化同步系統的動態性能；在深入了解系統的動作特性后，對plc控制研配液壓機的原理進行了探討，針對siemens公司s7 ? 200型plc給出了硬體設計的總體規劃，編制出研配液壓機動作控製程序，在編程中著重研究位移傳感器與plc的通訊、雙缸同步運行的pid控制在plc上的實現及bcd碼撥盤輸入程序的植入問題。
  8. Besides, parker is also a famous supplier for refrigeration and air conditioning components including all kinds of sporlan products, such as mechanical and electric expansion valves, solenoid valves, filter driers, sight glasses, level master liquid controls, mechanical and electric pressure regulating valves, check valves, shut off valves, oil separators, and other industrial valves for r717 etc

    除此之外，派克漢尼汾還是一家全球著名的冷凍與空調另部件的供應商，其中包括美國斯坡蘭生產的各種產品，如，機械的和電子的膨脹閥，電磁閥，乾燥過濾器，視鏡，液位控制器，機械的和電子的壓力調節閥，單向閥，截止閥，油分及工業用氨閥等等。
  9. Based on comparison of several motor candidates, doubly salient permanent magnet ( dspm ) motor is a good choice for it ’ s outstanding performance. similar to conventional drive system, dspm brushless dc motor ( dspm - bldcm ) is composed of dspm motor and it ’ s controller. the controller is made up of three - phase full - bridge inverter, driver, dsp control unit and etc. for high power system, every switch of three - phase inverter is actually made up of four mosfets in parallel

    在充分考慮國內外不同的液壓泵電動機的基礎上，本文選用了雙凸極永磁電機作為整個系統的電機本體，並配以電動機控制器（控制器包括三相橋式功率變換器、驅動電路、 dsp主控單元、電流采樣及預處理和位置采樣及預處理等主要部分）組成整個液壓泵電動機系統。
  10. The real - time fuzzy control respectively for the three - section electric furnace and three tank liquid level experiment equipment is carried out to show the effectiveness of the fuzzy controller designed by fcds, in the mean while realize integrately run with forcecontrol and kingact configuration software

    通過對三溫區電加熱爐和三容液位控制實驗裝置的實時模糊控制，實現了利用fcds設計模糊控制器，並與「力控」 、 「組態王」組態軟體的集成運行。
  11. First introduces hardware platform of mine monitoring system that adopt embedded pcm - 3350 to be as main controller, big - capability memorizer cf card as memories, 10. 4 inch lcd liquid crystal screen as display, pcm - 3612 as communication extend cell ; rs232 and keyboard as i / o interface to realize data dispose, storage and transport function, and so on. then introduces some basic concept and core character about embedded operating system windows ce. at the same time, the paper has a detailed introduction about platform - configured tool platform builder of mbedded operating system windows ce and a detailed narration abut the whole process of configuring the embedded operating system base on yanhua pcm - 3350, then the paper depletes the characteristic function and system framework of embedded configuration software mcgs generally and introduces the design process about configuration software of mine monitoring - control system ; at last, the paper introduces main function of rk512 communication protocol that can ensure reliable communication with controller plc of bottom machine

    首先介紹了硬體平臺的搭建：採用嵌入式pcm - 3350作為主控制器；大容量的存儲器cf卡作為存儲設備；採用10 . 4寸lcd液晶屏作為顯示設備； pcm - 3612作為通信擴展單元；用rs232和鍵盤作為i o介面來實現數據的處理、存儲和傳輸等功能；然後又介紹了嵌入式操作系統windowsce的一些基本概念、核心特性，同時對嵌入式操作系統windowsce的平臺定製工具platformbuilder做了一些介紹並詳細敘述了使用platformbuilder定製基於研華pcm - 3350的windowsce操作系統的過程；接著概括敘述了可運行在windowsce上的嵌入版組態軟體mcgs的特點、功能、體系結構並詳細介紹了礦山檢測系統的組態軟體設計過程；最後介紹了能夠與下位控制器plc可靠通訊的rk512通訊協議的主要函數。
  12. So it could be used for level control and measurement of flammable and explosive oil and other chemical liquids, specially for the precise measurement of liquid level in small tanks

    該傳感器可廣泛應用於石油化工系統的多種液體的液位控制和測量，特別適用於小型容器的液位精確計量。
  13. Abstract : the objective, characteristic and application of the nonlinear control strategy are introduced. how to apply and implement the function of the controller, how to start and stop the control strategy and trouble shooting is discussed. result of commissioning show that the application of nonlinear level control strategy in rfcc of qianguo oil refinery was successful

    文摘:簡要介紹了非線性液位控制策略的目的、特性、應用，並著重介紹非線性液位控制系統實施過程和控制器功能，控制器的投運和控制器的故障處理，由投用效果看出非線性液位控制系統在前郭煉油廠重油催化裂化裝置得到了很成功的應用。
  14. The stabilised naphtha is routed to the naphtha splitter on level control of the debutaniser bottom product compartment ( cascaded through a flow controller )

    在脫丁烷塔底產品室液位控制下（通過一個流量控制器串級） ，穩定石腦油被引到石腦油分餾塔。
  15. The three - tank control system is consisted by two kinds of controlment that are the liquid - level control and temperature control. different control had different character, so we use different control strategy. in order to gain good quality of water level, we use fuzzy control strategy. in order to control the temperature of tank t2 quickly and smoothly, we use fuzzy pid strategy. at last we draw a interface of man - to - machine using rsview32, from which we can monitor the process in industry

    溫度控制採用模糊控制演算法，液位控制採用模糊pid控制演算法。最後用rsview32編制了一個人機界面，可以從此界面中監視生產過程的運行情況。三水箱計算機變頻控制系統採用變頻器進行電機調速后，耗費電能大大降低，同時由於控制策略選擇適當，系統運行比較平穩。
  16. The hardware - in - loop simulation of evaporator liquid level control system is designed. smar system302 is used as control system. the hmi design is made

    進行了蒸發器液位控制系統的半實物模擬設計，其中控制系統採用smarsystem302現場總線系統實現。
  17. The article have been discussed theoretically for some technology control system of continous casting, for example mould level control system, electromagnatic mould stirring system, soft - reduction, the secondary cooling water control ect

    並對連鑄一些特殊工藝控制如結晶器液位控制系統、結晶器電磁攪拌、輕壓下、二冷控制等進行了理論探討。
  18. The article in lead - zinc mineral tailing transmission pumps electric motors automatic control system of huang - shaping, for example, a detailed account of the system frequency conversion governor, ultrasound liquid position controller design models, debugging points and parameters set methods, and energy saving effect of a careful analysis

    摘要文章以黃沙坪鉛鋅礦尾礦輸送泵電動機自動控制系統為實例，詳細介紹了系統中變頻調速器、超聲波液位控制器的設計選型、調試要點和參數設定方法，並對節能效果進行了認真分析。
  19. Li ye wei control system installed to ensure that the machines normal work

    設置液位控制系統，確保機器正常工作。
  20. Application of genetic tuning based fuzzy immune pid controller in liquid - level control system

    控制器在液位控制系統中的應用研究
分享友人
分享到 Line

分享到臉書