液力懸置 的英文怎麼說
中文拼音 [yèlìxuánzhì]
液力懸置
英文
hydro-mount-
In the design of loading - frame, puting forword a group of universal dimensions of three - point free - link attachment to category i and ii tractors through comparing and analysing whose scope of dimensions, thereout, working out sketch of loading framework on several different positions in the whole lift - course of hydraulic liftenafter this. analysing the case of force on loading framework when the loading force equal to 44100n and the lift - position of the hydraulic lifter is on upper limit, and giving a data table about the case of force on all these positions, consequently, completing the design of loading frame
在加載框架的設計部分，通過對、類拖拉機的三點懸掛機構桿件尺寸范圍的比較分析，給出了一組、類拖拉機通用的三點懸掛機構桿件尺寸，由此作出了液壓提升器提升全行程中幾個不同位置的加載機構簡圖，並按44100n的加載力、以上極限位置為例對加載機構進行了受力分析，並給出了包括其它幾個位置在內的受力情況表，進而完成了加載框架的設計。The characteristic of engine exciting is analyzed. the hydraulic mount system " simulating calculation on idle working condition and high speed working condition is carried out by adams
分析了發動機激勵的特點，運用adams進行了動力總成液壓懸置系統的怠速和高速工況下的模擬計算。Based on a lot of references, the developing history of hydraulic mounts is reviewed. then they are classified by their structures. the working principle, characteristics, and weakness of each type are stated in detail
在閱讀大量國內外參考文獻的基礎上，對發動機動力總成液壓懸置元件的發展進行了系統的總結，並根據其結構進行科學分類，較為詳盡地闡述了各種液壓懸置的工作原理，性能特點，並指出了其不足之處，以及今後的發展方向。The fog is produced by a device ( thermal fogger ) that uses heat to break up the chemical into very small droplets ( usually in 5 - 30 micron diameter range ) which will disperse in the air
熱噴霧是經由一特製裝置（熱噴霧器） ，利用熱力把化學液體化為微細霧滴（直徑通常由5至30微米不等）散播並懸浮於空氣中。The response curve of rear left hydraulic mount, rear right hydraulic mount, and the fore rubber mount in each conditions are draught. the curve of hydraulic mount system ' s transmissibility is also calculated in the end and the performance of vibration isolation is analyzed. 5
繪制了在時域和頻域上的動力總成的加速度運動響應，質心的角加速度運動響應以及后左，后右液壓懸置，前橡膠懸置的動反力曲線，以及怠速，高速工況下各懸置的加速度功率譜密度曲線。A dynamics model for that engine mount is set up and a simulation on its dynamic characteristics is conducted using adams software with corresponding tests performed
通過試驗測試了電流變液力懸置的動態特性，並將模擬結果與試驗結果進行了比較分析。Based on the analyses on all kinds of structure and principle of hydraulic mounts, math mechanics model of hydraulic mount is set up by applying the theory of hydro - structure coupling, the mass parameters and geometry position parameters of each component in this model is imported into the software adams by entity data model established by three - dimension cad soft unigraphics. and dynamic analyse model of mount system is set up, simulation calculation is made on hydraulic mount component and mount system by using the software adams, the influence of model parameters on dynamic characteristics of hydraulic mount is analyzed and compared with experiment results, the correctness of hydraulic mount model is validated
本文在分析各種液壓懸置結構和原理的基礎上，利用流體結構耦合理論建立了液壓懸置的數學力學模型，模型各構件的質量參數、幾何位置參數通過三維cad軟體unigraphics所創建的實體數模導入到動力學模擬軟體adams中，建立懸置系統的動力學分析模型，並運用adams軟體對液壓懸置元件及懸置系統進行了模擬計算，分析了模型參數對液壓懸置動特性的影響，並且與試驗結果作了比較分析，驗證了液壓懸置模型的正確性。As a main product of our company, spraying drying set is a kind of centrifugal or pressurized, which atomizes liquid materials such as solution, suspension, emulsion or paste into timy droplet ( surface area increased ) and dry them into powder product an once ( several to dozens of seconds ) by contacying hot air
噴霧乾燥機組是一種用離心式或壓力式霧化器，將溶液、懸浮液，乳濁液或漿料等料液霧化成細微液滴（表面積顯著增大） ，經與熱風接觸得以急速乾燥（幾秒到幾十秒） ，從而直接得到粉末產品的裝置。分享友人