液固比 的英文怎麼說

中文拼音 [yègùbǐ]
液固比 英文
liquid-to-solid ratio
  • 液 : 名詞（液體） liquid; fluid; juice
  • 固 : Ⅰ形容詞（結實; 牢固; 堅硬） firm; hard; solid Ⅱ副詞1 （堅決地; 堅定地） firmly; resolutely 2 [書...
  • 比 : Ⅰ動詞1 （比較; 較量高下、 長短、距離、好壞等） compare; compete; contrast; match; emulate 2 （比...
  1. When extraction solvent acetic acid to alcohol ratio was 1 : 5, solid to liquid ratio was 1 : 15, 40, 36hours, the bacteriostasis of chilli extraction was best

    當提取劑中乙酸：乙醇為1 ： 5 ，固液比為1 : 15 ，提取溫度為40 ，時間為36小時辣椒提取物的抑茵效果最佳。
  2. By comparing the dry plate pressures drop and distributions of velocities simulated on single valve with those of double valves, it was found that there was intense turbulence in the flow fields around fixed - valve, there were eddy areas between valve side orifices and tray wall, there were eddies above the valves too, these led to the complex behaviors of gas perforating valve, these had a great effect on the gas - liquid mass transfer process. at the same time, in order to prevent the disadvantageous effect of gas between one valve with another on the gas - liquid mass transfer, it was very effective to change the fields of gas perforating valve by folding the edges of valve

    通過對數值模擬得出的單閥和雙閥塔板的干板壓降及流場速度分佈分析對比后發現，固定閥周圍流場存在較強的湍動，閥側孔與塔板壁面區域以及閥體的上方空間存在明顯的渦流區，使氣體穿閥后的行為變得復雜，並對氣液傳質過程產生重大影響；模擬結果表明，為防止和削弱固定閥間的對沖造成的「死區」對傳質帶來的不利影響，通過折邊來改變氣體的氣路是非常有效的，模擬值與實驗值基本得到吻合。
  3. For same mineral, desorption of 125i " on it was weaker than 125io3 ", and sorption of 125i i25io3 " on galenite is irreversible. apparent diffusion coefficient da of 125i " in the mixed material were determined by the pass - through diffusion way, da values under atmosphere was given : da = 7. 29x10 - 12m2 ? s - 1

    大氣條件下，隨體系固液比的減小，固相的量相對在下降， 125i -在礦物材料上的kd值減小；隨材料粒度的減小，材料的比表面積增加， 125i -在礦物材料上的kd值有所增加。
  4. Some main results of testing research were as fellows : i. in the course of testing of leaching zinc dross, leaching zinc dross by sulfuric acid was researched and the effects on the leaching rate of the zinc dross were analyzed by author, the optimum conditions of leaching testing of zinc dross were determined as fellows : liquid - solid ratio 6 : 1, stirring ratio 250r / min, granularity 120 mesh, the soaking time 5h, the concentration of sulfuric acid of 30 %, and under these conditions, the rate of leaching zinc is above 92. 0 %. ii. in the course of testing of purification, on the basis of comprehending and comparing all present methods of the manganese - removal and iron - removal, the oxidizing method of manganese - removal in zinc sulfate solution using ammonium persulfate was put forward and the oxidizing method of iron - removal in zinc sulfate solution using the goethite process and oxidation - hydrolysis process was adopted

    研究的主要結果具體如下： 1 、研究了硫酸浸出鋅浮渣並分析了影響浸出率的各種因素，確定了浸出鋅浮渣的最佳條件為：液固比為6 ： 1 ，攪拌速度為250r min ，粒度為- 120目，酸浸時間為5 . 0h ，硫酸濃度30 ，鋅浮渣的浸出率大於92 . 0 ； 2 、在綜合和比較了目前除錳和除鐵的各種方法基礎上，提出了過硫酸銨氧化除錳方法和選擇了針鐵礦-氧化水解聯合法除鐵方法，並分析和討論了影響除錳率和除鐵率等各種因素，確定了除錳的條件為：溫度90 ， ph值5 . 4 ，反應時間3h ，過硫酸銨達到理論值的1 . 2倍，除錳率超過99 . 86 ；聯合法除鐵的條件為：氧化反應時間1 . 5小時、溫度控制在90 92 、 ph值5 . 2 5
  5. Based on the close analysis of the influence factors of the vertical bearing capacity, circular aperture extension theory is employed to establish the computing formulas for the pile vertical stress and the foundation vertical bearing capacity, respectively. moreover, with analyzing the features of the calculation parameters such as materials of gunite mortar, jet pressure, diameter of the jet pipe, pile length, pile layout, a design theory for chemical churning pile composite foundation is proposed. then, the variation of the pipe deformation with loads, the deformation coordination of pile and soil are studied

    在此基礎上深入探討了旋噴樁的樁土受力特性及其復合地基的加固機理，從影響旋噴樁復合地基豎向承載力的因素入手，基於圓孔擴張理論給出了樁體豎向應力及旋噴樁復合地基的豎向承載力計算公式;通過對噴射漿液、噴射壓力選取、噴射直徑估算、樁長及樁位設計等各種計算參數的深入分析和研究，提出了一套相應的旋噴樁復合地基設計計算方法;通過計算分析，深入探討了旋噴樁復合地基變形隨荷載變化規律、樁和樁間土變形協調關系、樁土應力比及復合地基壓縮模量的確定，並提出相應的設計方法和修正參數;此外，結合工程應用，對旋噴樁復合地基的施工技術及其現場質量檢測方法進行了較全面的探討。
  6. Components and physicochemical properties of blood ; concept of hematocrit value ; the number of blood cells ; physiologic properties and generating regulation of red blood cells ; blood coagulation ; abo blood group system

    血液的組成及理化特性；血細胞比容的概念；三種血細胞的數量；紅細胞的生理特性和生成調節；血液凝固； abo血型系統。
  7. As a rule, the immunosensors is to coat the surface of crystal with antibodies or antigens, immerge to muster solution, binding to the immobilized antigens or antibodies and take place immuno - reaction, can cause a frequency change of the quartz crystal, and the frequency changes are proportional to content of antigens or antibodies in muster solution

    通常將抗體（或抗原）固定於晶體表面，浸入樣液時，與抗原（或抗體）產生免疫反應，使晶體表面質量負載增加，頻率降低，其頻移值與樣液中抗原（或抗體）含量成正比。
  8. Furthermore, we try to fabricate complex perovskite structure pmn - pt by the conventional mixed oxide, liquid phase inclosure technique and microwave calcinations method

    同時也對直接固相合成法、液相包裹體法及微波合成工藝進行了相應的比較和探討。
  9. In this thesis, based on pershing ii surface to surface missile, a new kind of ballistic missile was designed with an additional rocket engine, which can be ignited twice. firstly, aerodynamic computational models of missile body and warhead which reentry with supersonic are built according to the task requirements ; secondly, the propulsion system model of missile is built whose first two stages are solid rocket engines and the third stage is liquid - solid combined rocket engine. the nozzle and the shape of the engine are designed to meet the needs of the populsion project ; thirdly, the trajectory model of the mass point is built and a wavy trajectory is designed & optimized ; finally, the ability of a missile ' s breaking through defence is analyzed

    以美國潘興導彈為原型，增加可兩次點火的末級發動機，改裝成具有跳躍能力的地地彈道導彈；首先，根據任務需求，建立了導彈的氣動模型，並建立了彈頭再入時高超聲速氣動模型；其次，建立了導彈推進系統模型，前兩級採用了固體火箭發動機，第三級採用了固?液組合火箭發動機，並在總體方案要求下，對發動機噴管和外形進行了設計；第三部分，建立了導彈質點彈道模型，設計了一條跳躍式彈道，並對跳躍式彈道進行了優化設計；最後，對導彈進行了突防能力分析，從分析的結果可以看出，跳躍式彈道的突防能力比常規的拋物線彈道要強。
  10. The tail gas absorption solution is returned to the crystallizer, thereby adjusting the liquid - solid ratio, and improving the phosphogypsum crystals with the entrained ammonium ions, with the result that the available components are recovered, and clean production and economic benefit are realized

    同時，尾氣吸收液返回結晶槽一方面可以調節液固比，另一方面帶入的銨根離子可以改善磷石膏的結晶，既回收了有效成分，又實現了清潔生產與經濟效益雙豐收。
  11. Abstract : this paper researches into the complex adhesive ， which was mainly made by the soy protein isolate ( spi ) and polyvinyl alcohol or polyvinyl acetate. different composition of protein and polymers can perform different characters, together with other ingredients. the factors, which are related to the first adhesive strength and adhesive strength, are mainly studied and discussed. the first adhesive strength of the complex adhesive is related to the content of spi, and the adhesive strength is related to the content of the complex adhesive. on the basis of the researching, we can make the plant fibre box for food in the future

    文摘:對大豆分離蛋白?聚乙烯醇、大豆分離蛋白?白乳膠復合膠粘劑進行了研究，採用不同混合比例及添加其他助劑，得到較好性能和可生物降解的復合膠粘劑，為製造一次性植物纖維快餐盒打下基礎.主要研究了影響這種復合膠粘劑粘接木塊的初粘力（剪切和拉伸強度）和粘接強度的因素，實驗表明： 9 . 2 %濃度的大豆分離蛋白的初粘力（剪切和拉伸強度）優於10 %濃度的聚乙烯醇膠和33 %濃度的白乳膠；大豆分離蛋白復合膠粘劑的初粘力主要與大豆分離蛋白含量有關，其最終粘接強度與膠液固含量正相關
  12. Abstract ： in this paper, the methods including the reduction ball - milling, the optical induction, the chemical reduction, the liquid phase reduction, the liquid - solid phase reduction, the spray pyrolysis, the evaporation and condensation, and the atomization et al. which have been used for preparation of nanometer silver flakes and nanometer spherical silver powders in china since the 1990s were summarized under categories, the features of each method were compared, the development of preparation technology was looked forward to, in the meantime, the present application and potential application of nanometer silver powders were expounded

    摘要：本文分類總結了20世紀90年代以來國內納米片狀銀粉和球形銀粉的制備方法，包括還原球磨法、光誘導法、化學還原法、液相還原法、液-固相還原法、噴霧熱分解法、蒸發冷凝法及霧化法等，比較了各種方法的優缺點，展望了納米銀粉制備技術的發展，同時，論述了納米銀粉現有的和潛在的用途。
  13. In chapter two, according to n - s equation, considering the couple between liquid and solid, the double - fluid model is used to respectively set up momentum equations of two - phase fluids in condition of basic hypothesis, which are general equations of two - phase fluids. simplifying the equations in boundary layer, the momentum differential equations are required and the boundary conditions are given. in the same time, the simplifying equations and their solutions, in which solid grain satisfies in boundary layer

    第二章依據n - s方程，考慮到液、固之間的相間耦合，在基本假設條件下，採用雙流體模型，分別建立液、固兩相的動量方程，它是固液兩相流體的一般方程式；對其在邊界層流區內進行量級比較，得到邊界層動量微分方程並給出其邊界條件，同時也得到固體顆粒在邊界層內所滿足的簡化方程及其解的表達式。
  14. The reaction temperature, the proportion of solid materials, the liquid - solid ratio, the reaction time making fire - retardant low hydrated zinc borate from zinc oxide, zinc nitrate and borax were discussed

    摘要以氧化鋅，硝酸鋅和硼砂為原料生產阻燃劑低水合硼酸鋅，對生產工藝條件中的反應溫度，物料配比，液固比和反應時間等方面進行了研究。
  15. Aiming at the problems of reducing cost, increasing the separation efficiency of the solid and liquid, and improving the disperse rate and the photocatalytic effect of nano - tio2 when synthesizing in liquid phase, this dissertation, taking the natural minerals as carrier and the industrial metatitanic acid and the industrial black titanic liquid as the raw material, has studied the selection of the nature mineral, the methods and the conditions of the preparation of tio2 / mineral with nano - structure and the photocatalysis of the product

    本文針對在液相法制備納米二氧化鈦時，如何進一步降低生產成本，提高產物液固分離效率，以及改善二氧化鈦納米粒子的分散性和光催化效果等問題，採用天然礦物為載體，以工業偏鈦酸和黑鈦液為原料，從天然礦物篩選、功能材料制備工藝研究和制備方法比較、產品的光化活性等三個方面進行了研究。
  16. Finally, the analysis examples were presented combined with some real data from hydroelectric set, they showed that numerical simulation of fluid - solid coupling for vibration in this paper is more available and the natural frequency of guide vane in water is lower than that of in air

    運用ansys有限元軟體計算了水輪機導葉在空氣中的振動特性以及液固耦合振動的頻率和振型，並對二者進行比較，分析了影響振動的因素。通過算例表明，所採用的有限元數值模型合理，計算結果正確。
  17. Hydrocyclone is used to p urify bentonite according to the structure characteristicof hydrocyclone, the effects of apex diameter, flow quantities, liquid - solid ratio anddispersant on the recovery r atio and purity of bentonite have been studied, the optimumparameters of t echnology are put forward

    根據水力旋流器的結構特點，應用水力旋流器進行濕法提純的工藝流程，研究了底流孔徑、流量、液固比和分散劑對膨潤土含量和回收率的影響，提出了優化的工藝參數。
  18. According to several engineering examples, this paper has probed and contrasted quantitatively the effect of chemical grouting. based on longyang canyon and lijia canyon, the author has concluded that chemical grouting attained satisfactory effect on strengthening fault so long as choose suitable grout ratio. based on wanjiazhai engineering ^ the author has assayed the cause that the effect was n ' t reasonable, that has the order before grouting and quantity during grouting etc. therefore, some reasonable proposals have been tabled in relations to the grouting methods and quantity methods

    針對龍羊峽、李家峽兩個工程實例的對比研究得到結論，只要選擇合適的漿液配比，化學灌漿對斷層破碎帶的加固是可以取得令人滿意的效果的；針對萬家寨工程的研究，對其效果不理想的情況，分析了其出現的原因主要可能是由於其灌漿前處理進行的順序及施工質量等，進而對以後的灌漿方法、施工方法等做一些合理化建議。
  19. It was found be compared the two - phase flow of power law fluid - solid with that of liquid - solid that the fluid velocity of power law fluid - solid was bigger than that of liquid - solid and the particle velocity distribution of power law fluid - solid was flatter than that of liquid - solid

    對帶顆粒的冪律流體的兩相流流動與液固兩相流流動做了比較，冪律流體兩相流的流體速度在管道中心附近的大部分區域比液固兩相流的流體速度流動的速度大，而顆粒相的速度分佈比較平坦。
  20. Main applies : this machine is a kind of experimental equipment, which is used for separating suspending liquid, emulsion, it is especially suitable for the rare particle of density which specific gravity is bad and very little. such as firm liquid separation, liquid - liquid firm separation

    該機作為一種實驗設備，主要用於分離各種難分離的懸浮液，乳濁液，特別適用於濃度稀顆粒細比重差甚微的，固一液液一液液一液-固分離。
分享友人
分享到 Line

分享到臉書