淬火機理 的英文怎麼說

中文拼音 [cuìhuǒjīlǐ]
淬火機理 英文
mechanism of quenching
  • 淬 : 動詞（淬火） temper by dipping in water, oil, etc. ; quench
  • 火 : fire
  • 機 : machineengine
  • 理 : Ⅰ名詞1 （物質組織的條紋） texture; grain （in wood skin etc ） 2 （道理;事理） reason; logic; tru...
  • 機理 : mechanisation; mechanization; mechanism
  1. Based on the analyses on mechanical properties, microstructure and fracture of - the microalloyed steels socrv with various heat treatment technique, it can be affirmed that various fractures arttribute to various mechanism, we can draw conclusion that the strength and toughness of microalloyed steels 50crv will be increase simultaneously by optimal heat treatment technique. to illustrate the mechanism of the strength and toughness of microalloyed steels socrv, we designed the comparative experiment and observed the microstructure of the sample which occurred at different quench and tempering temperature and different tempering time. the last experiment results were determined by the four factors : fined microalloyed elements grains, the decompound of martensite, martensite transformation of remnant austenite and the second phase precipitation

    為解釋微合金化50crv鋼強韌化機理，本文通過對不同淬火溫度，回火溫度，回火時間下的力學性能指標的對比及顯微分析，認為微合金元素的細化晶粒，馬氏體的回火分解，殘余奧氏體的轉變，第二相的沉澱析出共同決定了微合金鋼的強韌化情況，特別是由於微合金元素的存在，其細化晶粒及其碳氮化物的沉澱析出，導致鋼的良好的強韌性，並且如果工藝滿足第二相的沉澱析出強化大於回火馬氏體分解引起的軟化效應，會在硬度曲線中產生明顯的二次硬化現象。
  2. The result shows that the quenching inductor with wimble magnet inlaid is adaptable for this technique, and the vertical quenching machine can be used in mass production

    結果表明，帶錐角鑲嵌導磁體的圈式感應器，其有效圈高度、錐角和內徑的合理匹配可以滿足淬硬層形態的要求，採用立式淬火機床連續淬火可以大批量生產合格的半軸。
  3. Product description : this series product has entire auto - lubrication systems and the ordinary two big kinds supplies to select, this machine major parts cancels the needle, cam and the ball bearing all uses the high quality import components, also selects the high quality steel products quenching heat treatment to the main stress components, the essential components uses special phosphorus processing, the foreign dew components all adopts special - purpose seal - up device and drains the oil the measure, therefore, entire causes machine throughout to locate the lubrication is reliable, the revolution is steady, under the high speed low chirp condition works

    本系列產品具有全自動潤滑型及普通型兩大類以供選用，本機主要零件勾針，凸輪及滾珠均採用優質進口零件，對主要受力零件亦選用優質鋼材淬火熱處理，關鍵零件則採用專門磷化處理，對外露零件均採取專用密封裝置及排油措施，因此，使整機始終處于潤滑可靠，運轉平穩，高速低噪的條件下工作。
  4. Aimed to realize the problem of quenched rail qualification forcast through quantitative analysis of quenched rail surface hardness by eddy current, and combined the eddy current theory with the computer image processing and signal analysis, the hardness testing model is established in this paper

    針對渦流無損檢測淬火鋼軌踏面硬度的定量分析來實現淬火鋼軌質量保證預報問題，將電渦流理論與現代計算機圖象處理和信號分析相結合，完成硬度測試模型建立。
  5. Abstract : aimed to realize the problem of quenched rail qualification forcast through quantitative analysis of quenched rail surface hardness by eddy current, and combined the eddy current theory with the computer image processing and signal analysis, the hardness testing model is established in this paper

    文摘:針對渦流無損檢測淬火鋼軌踏面硬度的定量分析來實現淬火鋼軌質量保證預報問題，將電渦流理論與現代計算機圖象處理和信號分析相結合，完成硬度測試模型建立。
  6. Results of the experiments showed that the wear mechanisms of the sintered steel included abrasive wear, adhesive wear and fatigue wear, and it was the abrasive wear most important. it was the sintered steel mixed by ni, mo that was the best on the wear resistance, because of the great lot of bainite ; the sintered steel quenched and low temperature tempered mixed by mo, w that was the best on the wear resistance, because of the rigidity of the steel was the highest

    實驗結果表明：本文中幾種燒結鋼的磨損機制均是由磨粒磨損、粘著磨損、和疲勞磨損共同作用的，且以磨粒磨損為主；在燒結態下，復合添加合金元素鎳、鉬的燒結鋼的耐磨性能最好，這是因為生成了大量的硬質相貝氏體；而淬火、低溫回火態下，則復合添加鉬、鎢的燒結鋼的耐磨性能最好，這是因為熱處理態下添加鉬、鎢的燒結鋼的硬度最高。
  7. Strengthening mechanism of ion nitriding is different from surface quenching and cementation, which makes surface strengthen by quenching to get martensite. ionic nitriding is the way to make materials strengthe n, which result from the steady compound formed on the surface of the metal. there is no need for quenching after treatment

    離子滲氮的強化機理不同於表面淬火，滲碳等表面熱處理方法，這些方法必須進行淬火得到馬氏體使表面強化，而離子滲氮是在金屬表面形成穩定化合物而使材料強化，處理后不須淬火。
  8. Analysis is done to the situation and gap of the carding clothing both at home and abroad in regarding their design, material selection, manu precison and quenching durobility for the requirement of modern machines. references is given to chinas manafacture of the same

    根據當代清梳聯高產梳棉機對關鍵梳理元件的要求，從配用的錫林、道夫針布齒條的設計、原材料選用、製造精度、淬火硬度入手分析了國內外的現狀及差距，並通過對國外知名針布公司的相關介紹，為我國針布齒條製造技術進步提供了可靠的依據。
  9. Abstract : analysis is done to the situation and gap of the carding clothing both at home and abroad in regarding their design, material selection, manu precison and quenching durobility for the requirement of modern machines. references is given to china ' s manafacture of the same

    文摘:根據當代清梳聯高產梳棉機對關鍵梳理元件的要求，從配用的錫林、道夫針布齒條的設計、原材料選用、製造精度、淬火硬度入手分析了國內外的現狀及差距，並通過對國外知名針布公司的相關介紹，為我國針布齒條製造技術進步提供了可靠的依據。
  10. In chapter four, in our experiments, we selected four representative mould steels as samples. after laser heat treatment, the hardness of samples was measured by special instrument, microstructure was also photographed to be analyzed carefully. through these experiments, we also debated on the theories which explain the new phenomenon occurring in laser overlapping treatment

    第二章：介紹了工業中的各種激光加工技術和激光加工系統，詳細說明了本實驗所使用的高功率激光加工系統；第三章：詳細敘述了激光淬火的機理和熱傳導數學模型；第四章：通過實驗，分析激光淬火后的模具鋼的硬化帶的硬度分佈及金相組織特性，同時對激光交疊熱處理的特點及形成機理都作了深入的探討。
  11. Annealing could reduce hardness and raise toughness, which could be prone to mechanical machining. quenching and low temperature tempering could raise intensity and hardness of materials, not reduce toughness obviously. quenching on same temperature caused ticp / fe in situ composites having the best integral machine properties

    退火處理使材料的硬度降低，韌性提高，便於機械加工；淬火+低溫回火處理使材料的強度和硬度提高，而韌性無明顯的降低；採用等溫淬火工藝，可使tic _ p fe復合材料具有最好的綜合機械性能。
  12. The effect of plastic deformation and elastic strain energy induced by pre - strain on the nucleation of martensitic transformation of low alloy ultra - strength steel sosimncrmov had been studied by pre - strain quenching in austenite state. the control over deformation magnitude and deformation temperate as well as loading pattern was performed to adjust the storage of elastic strain energy in steel before martensitic transformation, using the type of geeble - 1500 thermal analogue test machine

    使用gleeble - 1500型熱模擬機，對低合金超高強度鋼30simncrmov實施奧氏體預應變淬火處理，通過控制形變量、形變溫度和加載方式，調整鋼中馬氏體相變前的彈性應變能儲備，研究了預應變所造成的塑性變形與彈性應變能對馬氏體相變的影響。
  13. In this thesis, we studied the effect of laser heat treatment and overlapping treatment on mould steel, debated on the principle of laser heat treatment, and explained the new phenomenon observed in this experiment. to some degree, maybe our research is beneficial to the development of laser heat treatment technology in practice

    本文的研究了激光淬火以及激光交疊熱處理對模具鋼性能的影響，分析了激光熱處理的機理，對實際工作會有一定的實際意義，激光淬火也會隨著激光器的發展有更廣闊的應用前景。
  14. 2. heating treatment : 1300065002580mm annealing furnace max furnace is 120t, the high temperature is 11500c, 620023001500mm hardening furnace, 11005000mm line - frequency hardening machine tool

    2熱外理： 1300065003580mm退火爐最大裝入量120t最高爐溫11500c 620023001500mm淬火爐11005000mm工頻淬火機床。
  15. This jv invested rmb 10million in manufacturing plc controlled hot - rolling production line to produce blank of inlay knife

    其中包括從德國進口的可加工6米長刀片的平面刀口磨床、數控鉆銑床和從法國進口可減少熱處理變形的壓力淬火機。
分享友人
分享到 Line

分享到臉書