淬硬層深度 的英文怎麼說
中文拼音 [cuìyìngcéngshēndù]
淬硬層深度
英文
depth of hardening zone- 淬 : 動詞(淬火) temper by dipping in water, oil, etc. ; quench
- 硬 : 形容詞1 (堅硬) hard; stiff; tough 2 (剛強; 堅定; 強硬) strong; firm; tough; obstinate 3 (勉...
- 層 : i 量詞1 (用於重疊、積累的東西 如樓層、階層、地層) storey; tier; stratum 2 (用於可以分項分步的...
- 深 : Ⅰ形容詞1 (從上到下或從外到里的距離大) deep 2 (深奧) difficult; profound 3 (深刻; 深入) thor...
- 度 : 度動詞[書面語] (推測; 估計) surmise; estimate
- 深度 : 1. (深淺程度) degree of depth; depth 2. (觸及事物本質的程度) profundity; depth
-
Methods of measuring case depth for steel hardened by flame or induction hardening process
鋼的火焰加熱淬火或感應加熱淬火硬化層深度的測量方法Moreover, a method for iterating thermal and magnetic analysis is put forward. in chapter 5, the distributed characteristics of eddy and temperature fields in induction heating process are simulation by fem respectively, including the distributions of eddy and temperature fields during the whole induction heating process, the influence of frequency and magnetic disperse, and the prediction of hardened depth
第五章:用ansys軟體對感應加熱過程中工件內渦流場、溫度場的一些基本問題進行模擬及分析,主要包括:加熱過程中工件渦流功率密度及溫度分佈規律;頻率與磁力線逸散對加熱效果的影響;同時對感應淬火淬硬層深度進行了模擬預測。Abstract : a new simulating method is established for the calcul ation of the hardness profile of high - carbon - concentration deep - carburization, on the basis of analyzing this process and taking into account the influence o f carbide solution and dissolution, carbon - concentration and temperature on the diffusion behavior, and the influence of the environment factor on carbon trans fer through the gas - solid interface
文摘:在對高濃度深層滲碳的特點進行分析的基礎上,考慮到碳化物的析出與溶解、溫度及碳濃度對擴散行為的影響,氣氛環境對相界面碳傳遞過程的影響,淬火烈度對滲碳層冷卻效果的影響,提出了一種新的模擬高濃度深層滲碳滲層硬度分佈的方法。Determination of effective depth of hardening after induction or flame hardening of steel
鋼的感應淬火或火焰淬火後有效硬化層深度的測定Steels - determination and verification of the depth of carburized and hardened cases
鋼件滲碳淬火硬化層深度的測定和校核Ferrous metals, non - ferrous metals, ic thin sections, coatings, ply - metals ; glass, ceramics, agate, precious stones ; hardness testing such as that on the depth and the trapezium of the carbonized layers and quench hardened layers
黑色金屬、有色金屬、 ic薄片、層壓金屬、表面塗層;玻璃、陶瓷、瑪瑙、寶石等;炭化層和淬火硬化層的深度及梯度的硬度測試。Sintered ferrous materials, carburized or carbonitrided - determination and verification of case - hardening depth by a micro - hardness test
燒結鐵類材料.滲碳或碳氮共滲.用微型硬度測試法測定和驗證外層淬火的深度Methods of measuring case depth
測量淬火硬化層深度的方法分享友人