淬硬深度 的英文怎麼說

中文拼音 [cuìyìngshēndù]
淬硬深度 英文
depth of case
  • 淬 : 動詞（淬火） temper by dipping in water, oil, etc. ; quench
  • 硬 : 形容詞1 （堅硬） hard; stiff; tough 2 （剛強; 堅定; 強硬） strong; firm; tough; obstinate 3 （勉...
  • 深 : Ⅰ形容詞1 （從上到下或從外到里的距離大） deep 2 （深奧） difficult; profound 3 （深刻; 深入） thor...
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 深度 : 1. （深淺程度） degree of depth; depth 2. （觸及事物本質的程度） profundity; depth
  1. Methods of measuring case depth for steel hardened by flame or induction hardening process

    鋼的火焰加熱淬火或感應加熱淬火硬化層深度的測量方法
  2. Steel products. determination of the effective depth of hardening after flame or induction hardening

    鋼產品.表面或感應淬火后硬化有效深度的測定
  3. Iron and steel - determination of the conventional depth of hardening after surface heating ; german version en 10328 : 2005

    鋼鐵.表面加熱后常規淬硬深度的測定
  4. Moreover, a method for iterating thermal and magnetic analysis is put forward. in chapter 5, the distributed characteristics of eddy and temperature fields in induction heating process are simulation by fem respectively, including the distributions of eddy and temperature fields during the whole induction heating process, the influence of frequency and magnetic disperse, and the prediction of hardened depth

    第五章:用ansys軟體對感應加熱過程中工件內渦流場、溫度場的一些基本問題進行模擬及分析，主要包括:加熱過程中工件渦流功率密度及溫度分佈規律;頻率與磁力線逸散對加熱效果的影響;同時對感應淬火淬硬層深度進行了模擬預測。
  5. Abstract : a new simulating method is established for the calcul ation of the hardness profile of high - carbon - concentration deep - carburization, on the basis of analyzing this process and taking into account the influence o f carbide solution and dissolution, carbon - concentration and temperature on the diffusion behavior, and the influence of the environment factor on carbon trans fer through the gas - solid interface

    文摘:在對高濃度深層滲碳的特點進行分析的基礎上，考慮到碳化物的析出與溶解、溫度及碳濃度對擴散行為的影響，氣氛環境對相界面碳傳遞過程的影響，淬火烈度對滲碳層冷卻效果的影響，提出了一種新的模擬高濃度深層滲碳滲層硬度分佈的方法。
  6. Determination of effective depth of hardening after induction or flame hardening of steel

    鋼的感應淬火或火焰淬火後有效硬化層深度的測定
  7. Steels - determination and verification of the depth of carburized and hardened cases

    鋼件滲碳淬火硬化層深度的測定和校核
  8. In chapter four, in our experiments, we selected four representative mould steels as samples. after laser heat treatment, the hardness of samples was measured by special instrument, microstructure was also photographed to be analyzed carefully. through these experiments, we also debated on the theories which explain the new phenomenon occurring in laser overlapping treatment

    第二章：介紹了工業中的各種激光加工技術和激光加工系統，詳細說明了本實驗所使用的高功率激光加工系統；第三章：詳細敘述了激光淬火的機理和熱傳導數學模型；第四章：通過實驗，分析激光淬火后的模具鋼的硬化帶的硬度分佈及金相組織特性，同時對激光交疊熱處理的特點及形成機理都作了深入的探討。
  9. Ferrous metals, non - ferrous metals, ic thin sections, coatings, ply - metals ; glass, ceramics, agate, precious stones ; hardness testing such as that on the depth and the trapezium of the carbonized layers and quench hardened layers

    黑色金屬、有色金屬、 ic薄片、層壓金屬、表面塗層；玻璃、陶瓷、瑪瑙、寶石等；炭化層和淬火硬化層的深度及梯度的硬度測試。
  10. Sintered ferrous materials, carburized or carbonitrided - determination and verification of case - hardening depth by a micro - hardness test

    燒結鐵類材料.滲碳或碳氮共滲.用微型硬度測試法測定和驗證外層淬火的深度
  11. Methods of measuring case depth

    測量淬火硬化層深度的方法
分享友人
分享到 Line

分享到臉書