淬硬表層 的英文怎麼說

中文拼音 [cuìyìngbiǎocéng]
淬硬表層 英文
hardened skin
  • 淬 : 動詞（淬火） temper by dipping in water, oil, etc. ; quench
  • 硬 : 形容詞1 （堅硬） hard; stiff; tough 2 （剛強; 堅定; 強硬） strong; firm; tough; obstinate 3 （勉...
  • 表 : Ⅰ名詞1 （外面;外表） outside; surface; external 2 （中表親戚） the relationship between the child...
  • 層 : i 量詞1 （用於重疊、積累的東西 如樓層、階層、地層） storey; tier; stratum 2 （用於可以分項分步的...
  • 表層 : skin layer; superficial coat; veneer; surface; sexine; bloom; supercrust; surface layer表層沉積 [...
  1. The result shows that the quenching inductor with wimble magnet inlaid is adaptable for this technique, and the vertical quenching machine can be used in mass production

    結果表明，帶錐角鑲嵌導磁體的圈式感應器，其有效圈高度、錐角和內徑的合理匹配可以滿足淬硬層形態的要求，採用立式淬火機床連續淬火可以大批量生產合格的半軸。
  2. Abstract : this paper discussed the physicalmetallurgical process during laser hardening withsteel and cast iron, presented the technique designprinciple of laser hardening to achieve good resultsit also introduced the inspection method for laserhardened surface of steel and cast iron

    文摘:討論了鋼和鑄鐵在激光表面淬硬時的物理冶金學過程，提出了激光淬硬獲得優良效果的工藝設計依據，介紹了對鋼鐵零件激光淬硬表層的檢驗方法。
  3. Meanwhile, the fracture was accelerated due to the uneven surface hardness and the unreasonable distribution of the hardening layer on the crankshaft, and the bad lubrication condition in service

    同時軸左頸表面硬度不均勻、淬硬層分佈不甚合理，工作過程中潤滑條件差，加速了曲軸的斷裂。
  4. Moreover, it showed that the linearity rising relations were existed between the laser power and the thickness of hardening layer, and the linearity negative rising relations between the scanning velocity and peak rigidity

    此外，結果還表明激光功率與淬硬層厚度成線性增長，而掃描速度與峰值硬度成線性負增長關系。
  5. Considering different microstructures and properties of metal of hardened layer and the core of back - up roller, the distributions of shear stress below surface and the contact stress between work roller and back - up roller of a four - high - mill were simulated with nonlinear fem

    摘要考慮軋輥表面淬硬層與其心部金屬材料組織性能的差別，採用非線性有限元方法對四輥軋機的工作輥與支撐輥間接觸應力及輥內剪應力分佈進行模擬，並將模擬結果與傳統強度校核方法進行了對比分析，研究了軋輥淬硬層厚度對輥間接觸應力的影響規律。
  6. I. investigation on laser surface hardening for metal materials in this work, the effect of the process parameters in laser surface hardening on the properties and surface feature of the hardened layer was studied

    一、金屬材料激光表面硬化技術研究。研究了激光表面淬火工藝參數和硬化層性能、強化效果之間的關系，對大面積激光淬火技術的基礎理論及搭接方法對組織性能的影響規律進行了探討。
  7. Ferrous metals, non - ferrous metals, ic thin sections, coatings, ply - metals ; glass, ceramics, agate, precious stones ; hardness testing such as that on the depth and the trapezium of the carbonized layers and quench hardened layers

    黑色金屬、有色金屬、 ic薄片、層壓金屬、表面塗層；玻璃、陶瓷、瑪瑙、寶石等；炭化層和淬火硬化層的深度及梯度的硬度測試。
分享友人
分享到 Line

分享到臉書