渦輪式流量計 的英文怎麼說

中文拼音 [guōlúnshìliúliángjì]
渦輪式流量計 英文
turbine meter
  • 渦 : 渦名詞1. （漩渦） eddy; whirlpool; vortex 2. （酒窩） dimple
  • 輪 : Ⅰ名1 （輪子） wheel 2 （像輪子的東西） wheel like object; ring; disc 3 （輪船） steamer; steamboa...
  • 式 : 名詞1 （樣式） type; style 2 （格式） pattern; form 3 （儀式; 典禮） ceremony; ritual 4 （自然科...
  • 流 : Ⅰ動1 （液體移動; 流動） flow 2 （移動不定） drift; move; wander 3 （流傳; 傳播） spread 4 （向壞...
  • 量 : 量動1. （度量） measure 2. （估量） estimate; size up
  • 計 : Ⅰ動詞1 （計算） count; compute; calculate; number 2 （設想; 打算） plan; plot Ⅱ名詞1 （測量或計算...
  • 渦輪 : [機械工程] turbine; worm wheel渦輪泵 [航空] turbopump; roturbo; 渦輪發動機 turbine engine; 渦輪風...
  • 流量 : rate of flow; flow; runoff; discharge; throughput; （flow） rate; quantity （of flow）; flux
  1. Spiraling of the liquid as it reaches the rotor may affect the accuracy of the turbine meters.

    當液體接近轉子時發生紊流可以影響渦輪式流量計的精確度。
  2. Turbine meter has the advantages of high accuracy, fast response, and greater versatility under extreme operating conditions.

    在不良的工作條件下渦輪式流量計具有精度高，響應快和適應性廣等優點。
  3. In chapter 3, the subgrid eddy - viscosity model for large eddy simulation is applied to calculate the three dimensions unsteady periodic turbulent flow in yantan francis turbine. the pulsating characteristics of some main physical parameters in flow field are found. the calculated axial water thrust of hydraulic turbine agrees with the model - test value

    第三章採用大渦模擬亞格子渦粘模型，對巖灘混流式水輪機的流場進行三維非定常湍流分析，得到了流場中各物理量的脈動特性，計算出ms的軸向水推力與模型試驗值大小相當；同時論證了對于下機架承重的混流式水輪發電機組可採用其推力軸承負荷作為水電站廠房振動的最大垂直激振荷載。
  4. They are mainly used in manufacturing plants for ventilation or delivering gaseous materials and products thus they are considered the necessary equipment in ventilation, dust collection, acid and odor removal. there are numerous types of domestic products but most are exhausting fans, radial fans, vortex fans and axial fans. the technology controlled by domestic companies has been elevated from earlier dependent on international companies for technical assistance to self - sufficient in manufacturing

    除臭設備及焚化爐等設備不可或缺之一環，目前國內所產制之抽送風機種類繁多，而以抽風機、徑向式送排風機、渦輪式送排風機及軸流式送排風機居多，製造廠商之設計製造能力已由早期的仰賴國外技術支援而提升至相當之自製程度，目前國內所產制透浦式送風機之最大處理風量可達
  5. There are five parameters need to be measured. there are five channels for input : the displacement of casting - roller, the rotate speed of casting - roller, the pressure of casting and rolling, the casting temperature and the water - speed of cooling water. they are measured by raster, photoelectric coder, strain pressure sensor, thermocouple and turboflowmeter

    系統需要進行監測的參數有五個，即有五路輸入信號：鑄輥位移、鑄輥轉速、鑄軋壓力、澆鑄溫度、冷卻水流速，分別採用光柵、光電編碼器、應變式壓力傳感器、熱電偶和渦輪流量計作為檢測元件。
  6. It can automatically match rotational speed generator, electromagnetic rotational speed sensor and electromagnetic turbine flowmeter. moreover it can adapted measured signal that is 1v ~ 300v voltage and 1hz ~ 2500hz frequency

    能自動匹配測速發電機、電磁式測速傳感器和電磁渦輪流量計，適應電壓峰峰值從1伏以下至300多伏、頻率從1hz以下至2500hz以上的被測信號。
  7. Then, four different computation methods are applied to compute the hydrodynamic performance of the rotor, which are single - disk single - tube method ( sdst ), double - disk single - tube method ( ddst ), multi - tube method ( mtt ) that are based on momentum theorem and vortex method ( vtth ) that is based on potential eddy theory

    然後，採用基於動量定理的單盤面?單流管方法（ sdst ） 、雙盤面?單流管（ ddst ）方法、多流管（ mtt ）方法以及基於勢渦理論的渦方法（ vtth ）計算直葉擺線式水輪機的水動力性能。
分享友人
分享到 Line

分享到臉書