渦輪進口溫度 的英文怎麼說

中文拼音 [guōlúnjìnkǒuwēndù]
渦輪進口溫度 英文
turbine inlet temperature
  • 渦 : 渦名詞1. （漩渦） eddy; whirlpool; vortex 2. （酒窩） dimple
  • 輪 : Ⅰ名1 （輪子） wheel 2 （像輪子的東西） wheel like object; ring; disc 3 （輪船） steamer; steamboa...
  • 進 : 進構詞成分。
  • 口 : Ⅰ名詞1 （人或動物進飲食的器官; 嘴） mouth 2 （容器通外面的地方） mouth; rim 3 （出入通過的地方） ...
  • 溫 : Ⅰ形容詞（不冷不熱） warm; lukewarm; hot; gentle; mild Ⅱ名詞1 （溫度） temperature 2 （瘟） acute ...
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 渦輪 : [機械工程] turbine; worm wheel渦輪泵 [航空] turbopump; roturbo; 渦輪發動機 turbine engine; 渦輪風...
  • 進口 : 1 （船隻進港） enter port; sail into a port2 （外貿進口） import3 （入口） entrance; [機械工程] i...
  • 溫度 : [物理學] temperature
  1. Experimental studies on s1a - 02 gas turbine with water injection into compressor interstage / inlet as well as that on turbocharger self - loop test rig with inlet water injection are introduced. test results are in good accordance with simulation results, wet compression can lower compression work and increase engine power output so engine performance is enhanced, if engine power output is not changed, efficiencies of compressor and this engine become higher and turbine inlet temperature and fuel consumption become lower and if keeping t4 the same as that before wet compression is used, efficiencies become furthermore higher and engine power output increases greatly

    實驗結果和計算結果同樣表明：濕壓縮減少了壓氣機所消耗的壓縮功，增加了燃氣輪機的輸出功率，提高了燃氣輪機性能，如果保持發動機輸出功率恆定，濕壓縮可以提高壓氣機和整個燃氣輪機機組的效率，與此同時，渦輪進口溫度t _ 3 ~ *和燃油消耗率下降；如果保持渦輪排氣溫度t _ 4 ~ *恆定，壓氣機和燃氣輪機機組效率進一步提高，燃氣輪機輸出功率增加。
  2. Turbine intake temperature

    渦輪進口溫度
  3. A two - dimensional navier - stokes equation was solved to predict the unsteady, multipassage flow and temperature fields with hot streak in turbine inlet

    摘要通過求解二維n - s方程對多通道渦輪級進口有溫度畸變時的流場和溫度場進行了非定常數值模擬。
  4. Finally, in order to solve the problems encountered in experiment, an improved design, including gas path, mechanism and controller design, is proposed. experiments are accomplished in the improved system platform, and the results demonstrate that the improved system can meet the requirement of simulating the turbine outlet temperature of aero - engine

    最後，針對試驗中遇到的問題，從氣路部分、機械部分以及控制器三個方面對溫度模擬系統進行了改進設計，並在改進的系統平臺上進行了試驗，試驗結果表明改進后的系統能基本滿足對發動機渦輪出口溫度信號模擬需求。
  5. Based on the exhaust heat data of the iurbine ( 6160a - 12 ) and the micro gas turbine produced in japan, parameters of test - bed such as deferent thermal flow temperature and pressure are defined by the calculation of design parameter in method of combined theory and experience data

    以柴油機（ 6160a - 12 ）和日本的微型燃氣渦輪機尾氣參數為設計基礎，通過理論和經驗數據相結合的方法進行設計參數計算，確定了模擬實驗臺熱流量、出口溫度及壓力等參數。
  6. A temperature signal physical simulation method is proposed in this paper. the temperature simulation system is constructed and its controller is designed. the experiment results indicate that the temperature simulation system can meet the requirement of the matter - in - loop simulation of aero - engine control system

    本文提出渦輪出口氣體溫度信號的物理模擬方法，構建了溫度模擬系統，設計了溫度模擬系統控制器，進行了溫度模擬系統試驗，試驗結果表明溫度模擬系統基本滿足航空發動機控制系統半物理模擬的需求。
分享友人
分享到 Line

分享到臉書