測聲向儀 的英文怎麼說
中文拼音 [cèshēngxiàngyí]
測聲向儀
英文
direction-listening device-
Abstract : to present analysis of acoustic emission automonitor consisting. development status and prospect of an intelligent acoustic emission automonitor are put forward
文摘:分析了聲發射監測儀的結構，論述了聲發射監測儀的研製現狀與發展方向。Virtual ultrasonic detector ( vud ) is the result of the combination of virtual instrument technique and ultrasonic detecting technique. vud is smarter, cheaper than traditional instruments and represents the direction of ultrasonic flaw detecting. this paper put forward a project developed on the base of second generation vud
超聲波探傷是應用廣泛的無損檢測方法之一，虛擬超聲波探傷儀是虛擬儀器概念在超聲波探傷領域的應用，不僅實現了傳統的模擬超聲波探傷儀的所有功能，而且對傳統探傷儀的原有功能進行了擴展，使其具有一定智能處理能力，是超聲波探傷技術的一個重要發展方向。The conclusions are as follows : the ultrasonic intensity is proportion to the laser intensity ; the ultrasonic induced by a laser line source has much more advantages than by a laser point source, such as stronger energy, higher snr, more directivity and shape ; the intensity of cfpi ' s output signal is linear with ultrasonic vibration velocity, and is effected by incidence angle and scattered angle ; snr will increase by reducing cfpi ' s bandwidth, reducing incidence angle, increasing cavity ' s length and reflectivity
在分析點光源激勵聲表面波機理的基礎上，求出了線光源激勵的超聲振動的位移表達式，發現線光源激勵的近場區表面波具有波形好，信噪比高，指向性好，幅度強等特點。通過理論推導，得出共焦fabry - perot干涉儀的輸出光強除了與樣品表面的振動速度成正比，並與入射角和散射角有關；適當減小cfpi的帶寬，增加腔長，增大鏡面反射率，或者減小檢測入射角都可以提高系統的信噪比。The apsp produced abroad is made by numerical controlled machine tool, which has noise level of 71db ( a ), the apsp produced in our country is made in the method of exploratory which has noise level of 73db ( a ) and 75db ( a ). in order to analyze the influence of stator curve to noise, the author used tri - coordinate measuring instrument to measured exactly the inside surface of stator and got the straddling point coordinate, and made curve fitting by using matlab as language and studied the fitting effect and then worked out the equation of stator transition curve in return seeking, then comparied this method with the standard style and made the conclusion : the equation of atator transiting curve of apsp made by numerical controlled machine tool is close to theorical 5 power curve standard style, but compared with it, the stator transiting curve of apsp produced in exploratory has a major error. combining the testing results of noise, one can know that the qualily of stator transition curve play an importance to t he noise of the pump
國外生產的汽車動力轉向泵是用數控機床加工的，其噪聲值為71db （ a ） ，國內生產的汽車動力轉向泵是用靠模方法加工的，其噪聲值分別為73db （ a ）和75db （ a ） ，為了分析定子曲線對泵的噪聲的影響，本人用三坐標測量儀對定子內表面進行精密測量，獲得定子內表面的離散點坐標，以matlab語言為工具對離散點進行曲線擬合，觀察擬合效果，然後，用回歸方法求出了定子過渡曲線的方程，並把該方程與理論方程標準型進行了比較，得出如下結論：用數控機床生產的汽車動力轉向泵的定子過渡曲線方程非常接近理論5次曲線標準型，而用靠模方法加工的汽車動力轉向泵的定子過渡曲線與理論5次曲線標準型相比較，則存在著較大的誤差，結合噪聲測試結果可知，定子過渡曲線的優劣，對泵的噪聲大小有著重要的影響。分享友人