測角計頭 的英文怎麼說
中文拼音 [cèjiǎojìtóu]
測角計頭
英文
goniometer head-
Secondly, programmed the image processing arithmetic code which include the bottom arithmetic for the general condition comprises threshold division, region combination and informate and the middle level arithmetic for the given task comprises detecting the line dation creirection according to the hough transform in order to fix on the hole ’ s azimuth angle, detecting the aiguille tip position according to the image movement according to the environment and the image format
然後,根據目標環境要求和攝像機採集圖像格式,開發了圖像處理演算法程序。圖像處理演算法包括底層演算法和中層演算法兩部分,底層演算法針對通用情況,包括閾值分割、區域合併和信息生成。中層演算法針對具體任務設計,包括利用hough變換檢測棱線的方向,從而確定圓孔的方位角和利用基於圖像運動檢測鉆頭尖端位置。Methods : to divide the anatomic area into several parts : sigmoid sinus, jugular bulb, semicircular canal, internal acoustic meats, cerebellopontine angle area, duramater. simulated the partial labyrinthectomy and endoscopic surgery on 20 adult cadaveric specimens, measured correlative data, observed correlative anatomic structure. all data analysied by sas
方法:在20例40側成人屍頭上模擬迷路后徑路橋小腦角區內鏡手術和部分迷路切除術,將相關解剖結構分為乙狀竇、頸靜脈球、半規管、內聽道、橋小腦角區、硬腦膜等幾個區域,分別觀察相關解剖結構及測量相關數據,測量結果用sas軟體進行統計學分析。The open angle, head loss and hydrodynamic pressure under the rated flow and several kinds of proportion are carefully observed in the model test, and these results are given for reference in engineering design
階段模型試驗中詳細觀測了在額定流量下,不同比重拍門的開啟角度,水頭損失及門體動水壓力變化情況,以供工程設計應用參考。The main work and achievements of this thesis are as follows. 1. a hardware platform of binocular stereo measuring system with simple structure was built with low cost, which consists of ccd cameras, lens, a frame grabber card, a computer and a tripod
本文就這方面內容展開研究,主要研究內容和成果如下: 1 .以較低的成本建立了一個結構簡單的二目立體測量系統的硬體平臺,主要包括ccd相機和鏡頭,圖象採集卡、計算機、三角架。In this experiment, the data collecting and processing are finished by computer. according to the experiment, two conclusions can be drawn : first, not only to laser sensor but to inductance sensor, it is a good method for measuring the wheelset geometric parameters when the wheelset are made in factory or tested in the last working procedure in vehicle depot
此外,本文進行了測量原理的試驗研究:利用機床的xy平臺移動測量頭,同時調整其擺角,使傳感器的測量方向與輪輞模板的被測局部表面垂直,完成整個掃描測量;試驗中數據採集與處理由計算機完成。We introduce the design of non - contact laser otpical probe based on the triangulation technique, give the experimental results, review the applications of triangulation techniqne
介紹了基於三角測量原理的非接觸激光光學探頭的設計,給出了實驗結果,展望了應用前景。It ’ s been proved by the experiments that detecting apparatus system can be used to detect the laser beam divergence. the detecting results are very close to the given, attain the certain accuracy
實驗表明,本文設計的雙探頭測量激光發散角的裝置能夠較準確的測量出發散角的大小,測量結果達到了一定的精度。分享友人