滑塊位置 的英文怎麼說

中文拼音 [gǔkuāiwèizhì]
滑塊位置 英文
slide position
  • 滑 : Ⅰ形容詞1 （光滑; 滑溜） slippery; smooth 2 （油滑; 狡詐） cunning; crafty; slippery Ⅱ動詞（貼著物...
  • 塊 : 名詞（古時佩帶的玉器） penannular jade ring （worn as an ornament in ancient china）
  • 位 : Ⅰ名詞1 （所在或所佔的地方） place; location 2 （職位; 地位） position; post; status 3 （特指皇帝...
  • 置 : 動詞1. （擱; 放） place; put; lay 2. （設立; 布置） set up; establish; arrange; fix up 3. （購置） buy; purchase
  1. Secondly, calculation theory of construction for suspension bridge is presented under the ideal condition of dead load design. linetype change stiffness of cable and slip stiffness of supporting points are deduced based on segmental catenary theory. then numerical analysis method through sgkz2000 software are introduced in detail about calculating design linetype for suspension bridge, unstressed length of cable, erection linetype of cable and pre - displacement of saddle without loads, erection linetype of wire strands, the fixed position for erecting cable band and linetype of lifting stiffening girders

    其次，根據懸索橋恆載設計理想狀態建立了懸索橋施工計算原理；以分段懸鏈線索理論為基礎，推導了懸索的線形變化剛度和懸索支點的滑移剛度；介紹了懸索橋成橋設計線形計算、吊索無應力長度計算、空纜線形與預偏量計算、絲股架設線形計算、索夾安裝位置計算和加勁梁吊裝線形計算的具體方法、數值演算法及軟體sgkz2000的計算模塊的實現。
  2. The control precision of the slider with 2400mm effective stroke can reach 0. 05mm. the properties of the position control system are not exigent, only the dynamic non - overshooting and the stable - state - precision are considered. the system has given out satisfactory result when used in practical engineering, 0. 03mm position control precision has been achieved, on account of dead band, the performance of proportional valve is worse than that of servo valve, but some advantages of proportional valve has made it more fit for industrial control

    系統方案採用重復性能（反向回差）好的比例方向閥，使有效行程為2400mm的滑塊控制精度達到0 . 05mm ，位控系統快速性要求不高，主要考慮系統穩態重復精度，此方案在實際工程中已經取得了滿意的效果，位置控制精度達到0 . 03mm ，可以取代同類產品中日本川崎重工的泵控系統。
  3. On the base of model, considering the disturbance from the other 5 legs and variating load, we design an h - inf controller integrated with ip controller, which makes the system with the advantage of both h - inf control and ip control, and restrains the bad effect from variating disturbance. the simulation shows that this stradgy enhances the system robustness. in another solution, the coupling and load disturbances are regarded as the parameter variations of motor model, and the variation is observed, thus, the coupled dynamics of vamt is decoupled to 6 single motor systems

    在建立了模型的基礎上，本文針對單滑塊控制系統要受到其它滑塊及負載擾動的影響，採用h _控制方法設計的h _控制器與傳統ip位置控制器結合，使得系統具有ip位置控制器和h _控制的雙重優勢，有效地抑制了變化擾動對位置輸出的影響，模擬結果表明該方法大大提高了系統的魯棒性；本文提出的另一種方案是將桿間的耦合作用和負載擾動看作電機參數變化，利用觀測器進行觀測，從而將耦合的機床動力學系統解耦成為6個獨立的電機動力學系統。
  4. In this dissertation, the development survey, research actualities and application prospect of vamt are introduced at first, and the models of kinematics, dynamics and linear motor servo are analyzed then. currently the dynamics model is complex or established mechanically, which restricts the study of control theories. thus this dissertation present a simple and easy - realized control idea, namely, the fore and torque of every leg determined by the inverse - solution of mechanics are regarded as changeable load force ( disturbance ) applied in motor, the elongation of the leg or displacement of sliding is regarded as the output of linear servo system

    本文首先介紹了虛擬軸機床的發展概況、研究現狀和應用前景，然後對其運動學、動力學、直線伺服系統模型進行分析，針對目前動力學模型過于復雜或完全從機構學角度建立不便於控制的問題，提出了簡單、易於實現的控制思想，即將虛擬軸機床的動力學方程反解所確定的各桿受力（矩）視為電機的可變負載力，以桿長伸縮量或滑塊位移為伺服系統輸出，從此構成位置閉壞，實現軌跡跟蹤控制。
  5. The main module of sensorless pmsm vector control such as voltage sensing, current sensing, smo rotor position estimation, speed calculation, generation of sine and cosine, vector coordinate transformation, pi regulators, svpwm vector modulation are all accomplished in the pwm interrupt service routines

    永磁同步電機無位置傳感器矢量控制的主要模塊如電壓采樣、電流采樣、滑模轉子位置估算、速度計算、正餘弦值生成、矢量坐標變換、比例積分調節器、空間電壓矢量脈寬調制等都是在pwm中斷服務子程序中完成。
  6. The thumb position is always a discrete integral value. for instance, a scroll bar with a range of 0 through 4 has five thumb positions, as shown in figure 4 - 8

    滑塊位置總是一個離散的整數值。例如，范圍從0到4的滾動條有五個滑塊位置，如圖4 - 8中顯示。
  7. The slides and slideways of a machine tool locate and guide members which move relative to each other, usually changing the position of the tool relative to the workpiece

    車刀與車刀作相對運動，車刀的滑塊和滑道用於對各車刀進行定位和導向，通常也可改變車刀與工件的相對位置。
  8. Following the conditions, two stable equilibrium positions for compliant four - bar mechanisms with one or two characteristic pivots are found with use of the energy function

    提出了含有一個特徵鉸鏈和兩個特徵鉸鏈的四連桿柔性機械、特徵鉸鏈位置不同的曲柄滑塊柔性機械的雙穩態分析過程。
分享友人
分享到 Line

分享到臉書