滑油槽 的英文怎麼說

中文拼音 [gǔyóucáo]
滑油槽 英文
lubricating groove
  • 滑 : Ⅰ形容詞1 （光滑; 滑溜） slippery; smooth 2 （油滑; 狡詐） cunning; crafty; slippery Ⅱ動詞（貼著物...
  • 油 : Ⅰ名詞1 （脂肪; 油脂） oil; fat; grease 2 （姓氏） a surname Ⅱ動詞1 （用桐油、油漆等塗抹） apply t...
  • 槽 : 名詞1 （盛牲口飼料或飲料等液體的器具） trough; manger （for water animal feed wine vat） 2 （兩邊...
  • 油槽 : channel for oiling
  1. Gear lubricants may congeal and channel in cold weather

    天氣冷時齒輪潤滑油可能凝結而形成凹槽。
  2. On the east terrace - fault slope of the depression, the sedimentary mode of fan - shaped delta - slump turbid fan - deep lake facies are developed. on the long axial direction of fula depression, the southeastern groove was filled with a large scale delta which was the main sources, the other little delta limited by the 3 syndepositional fault was distributed down the slope edge of the northern sub - depression. this stage developed a favorable oil sources, reservoir and regional seal which formed the good matching relations of generation, reservoir and seal in the time - space zone

    Abugarbra組的sc和sd層序發育在邊界斷層和同沉積斷層活動劇烈、湖盆擴張期，凹陷中心發育半深湖-深湖相沉積，在凹陷陡坡發育近岸水下扇，斷階緩坡帶發育扇三角洲?滑塌濁積扇?深湖相組合，長軸凹槽和北部次凹的北部緩坡帶發育三角洲體系，此層位是有利生油層和巖性圈閉發育層段。
  3. Plain bearings - lubrication holes, grooves and pockets - dimensions, types, designation and their application to bearing bushes

    滑動軸承.潤滑油孔油槽和油穴.尺寸類型標記及其對軸套的應用
  4. There is one oil groove in the bronze bushing, where lubricant can flow into the axis from the oil hole on the cap of housings

    軸瓦內表面的不承擔載荷部分開有油槽，潤滑油通過進油孔和郵溝流進間隙。
  5. Through the statistic analysis on the change of the melt gear pump working condition pre - and post - pet plant capacity increasing and concatenate direct spinning process, the reasons for the unsteady running were studied, the modification measures such as lubricating the oil groove with sliding bearing, mechanical sealing of the gear pump, decreasing the gear pump outlet pressure, changing the automatic speed increasing to hand speed increasing were put forward

    摘要通過對聚酯裝置增容和後接直紡長絲前後熔體齒輪泵工況變化的統計分析，研究其運行不穩定的原因，提出改造措施，包括滑動軸承潤滑油槽，齒輪泵的機械密封，降低齒輪泵出口壓力，改自動提速為手動提速等等。
  6. Plain bearings ; hydrostatic plain journal bearings under steady - state conditions ; characteristic values for the calculation of oil - lubricated plain bearings with drainage grooves

    滑動軸承.穩定工作條件下靜壓向心滑動軸承.帶排油槽
  7. Plain bearings - wrapped bushes - lubrication holes, lubrication grooves and lubrication indentations

    滑動軸承.卷制軸套.潤滑油孔油槽和油穴
  8. Plain bearings - wrapped bushes - part 3 : lubrication holes, lubrication grooves and lubrication indentations

    滑動軸承卷制軸套第3部分:潤滑油孔潤滑油槽和潤滑油穴
  9. Plain bearings - wrapped bushes - part 3 : lubrication holes, lubrication grooves and lubrication indentations iso 3547 - 3 : 1999

    滑動軸承.卷制軸套.第3部分:潤滑油孔油槽和油穴
分享友人
分享到 Line

分享到臉書