澆注速度 的英文怎麼說

中文拼音 [jiāozhùsùdù]
澆注速度 英文
casting speed
  • 澆 : 澆名詞（姓氏） a surname
  • 注 : Ⅰ動詞1 （灌入） pour; irrigate 2 （集中） concentrate on; fix on; focus on 3 （用文字來解釋字句）...
  • 速 : Ⅰ形容詞（迅速; 快） fast; rapid; quick; speedy Ⅱ名詞1 （速度） speed; velocity 2 （姓氏） a surna...
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 速度 : 1. [物理學] velocity; speed; blast; bat 2. [音樂] tempo3. （快慢的程度） speed; rate; pace; tempo
  1. The control system of mould level is crucial to improve the slab quality in the continuous casting process, pid controller is used in the traditional mould level control, and it has some defaults, such as : at the start - up or finishing period of casting or during the changeover of tundish, pid control has a bad effect, its overshoot is large and its transient time is long ; the erosion of the tundish stopper and the submersed nozzles lead to the accuracy of control become bad ; the abrupt falloff of block in the submersed nozzles makes the level acutely fluctuate, and pid control can not overcome the disturbances resulted from the change of casting speed

    結晶器液位控制系統是提高連鑄產品質量的關鍵環節，傳統的連鑄機液位控制方法採用常規的pid控制，存在如下不足：開始、結束澆注和換中間罐澆注時，控制效果差，超調量大，過渡時間長；塞棒頭和浸入式水口被腐蝕后引起控制精度差；浸入式水口堵塞物的突然脫落所引起的液位劇烈波動；無法克服拉速波動引起的擾動。
  2. At the same casting speed, the eddy center is the lowest if the pouring angle is about 60 and the penetrating depth of molten steel flow increases with the increasing pouring angle

    在相同的拉坯速度下，隨著澆注傾角的增大，鋼液流股的穿透深度也隨之增大。
  3. The results show that the heat preservation coating and its proper thickness are favorable to the enhancement of filling mold speed of aluminium alloy ; the higher the pouring temperature is and the larger the ratio of hollow areas of vertical pouring is, the faster the speed of filling mold of aluminium alloy is ; if the mold is too thick or too thin, it may decrease the speed of filling mold ; the proper length and the area of vertical pouring are favorable to the enhancement of the speed of filling mold ; although negatire - pressure may improve filling the speed, too high negatire - pressure may enlarge the flaw in casting

    結果表明：保溫塗料及一定的塗層厚度有利於提高鋁液的充型速度；澆注溫度越高、直澆道空心面積率越大，鋁液充型速度越快；模樣厚度太厚或太薄，均會使鋁液充型速度降低；一定的直澆道長度及直澆道面積有利於提高鋁液的充型速度；施加負壓會使鋁液的充型速度大大提高，但負壓過大會增大鑄造缺陷。
  4. The effect of compound casting technology and compound modification on the properties of high speed steel roll collar was studied. the results showed that compound high speed steel roll collar with high and even hardness and good bond between outer and inner layers could be gained when the modified colbalt free high speed steel in outer layer and nodular iron inner layer in connection with appropriate rotational speed of centrifugal machine, pertinent pouring interval between two kinds of the melt and moderate pouring temperature as well as surface induction heat treatment were chosen. it is indicated in industrial use that the service life of compound roll collar is higher by 5 times than that of high chromium cast iron collar

    研究了離心復合鑄造工藝和復合變質處理對高速鋼輥環性能的影響，結果表明，選用變質高碳無鈷高速鋼作外層，用球鐵作內層，選擇合適的離心機轉速、兩種金屬熔液澆注間隔時間和澆注溫度，結合採用表面感應熱處理工藝，可獲得硬度高、均勻性好、內外層結合良好的高速鋼復合輥環，用於工業生產其使用壽命比高鉻鑄鐵輥環提高5倍以上。
  5. Find the law of the influence from the injection pressure to the filling time and the cavity pressure and make certain of the best filling time, injection time and injection pressure. though the analysis of the flowing velocity and pressure spread of the key position element in the injection parts in different gate position, we forecast the injection parts quality and the possibility injection flaw and its position, optimize the gate position. in this paper, though the research of analogue of the runner system of metal - powder injection molding and the process of injection molding, we get the law of how the injection parameter influence the injection process

    在相同的注射條件下，通過分析喂料在不同直徑和長度流道中的流動規律，得到了喂料在流道中的速度場、壓力場和溫度場，找到了流道長徑比的合理取值范圍，並得出通過改變流道設計可實現對現有設備資源充分利用的結論；給出了不同注射壓力下，型腔壓力與充模時間關系曲線和喂料熔體平均充填速度與充模時間關系的曲線，得到了注射壓力對充填時間和型腔壓力的影響規律，確定了最佳的充模時間、注射時間和注射壓力；通過分析採用不同位置澆口注射時注射件關鍵位置單元的流動速度和壓力分佈，預測了注射件的成形質量，或可能產生的注射缺陷及位置，優化了澆口設置。
  6. According to simulation results we decide the location of parting face and cooling system 、 the shape and location of runner and gating system etc. after that we take the az91d magnesium alloy shell of motorcycle engine as an example to proceed fine factors ( plunger injection speed 、 pouring

    然後以az91d鎂合金摩托車發動機外殼為例，進行五因素（壓射速度、澆注溫度、鍛造時間、壓射比壓、鍛造壓力）四水平l16 （ 45 ）正交實驗，在普通壓鑄過程中關閉鍛造功能。
  7. During the temperature fields, the results indicate that the processing parameters such as the extrusion velocity, casting temperature, perform preheating temperature, die preheating temperature and so on are important for the temperature fields besides the dwell time. they are must be in concordance each other to the deforming zone is in the quasi - solid state, and the stable semi - solid extrusion is implemented. during the deforming fields, the hyperbolic sine thermo - rigid - viscoplastic fem model is selected according to the forming feature of the process, and the variations of the stress - strain fields are studied

    在溫度場的模擬中，模擬結果表明，保壓時間是影響製件成形質量的關鍵因素之一，擠壓速度、液態金屬澆注溫度、預制體預熱溫度和模具預熱溫度等工藝參數對溫度場的影響也很大，需進行參數之間的協調，只有當變形區內部始終維持準固態時，才能實現穩定的液-固擠壓成形過程；在變形場的模擬中，根據液態浸滲擠壓的成形特徵，選用了雙曲正弦剛-粘塑性有限元計算模型，研究了變形過程中應力應變場的變化規律，研究了模角對變形和金屬流動的影響及變形力的變化過程和其影響因素。
  8. Liquid - solid extrusion of composite material is a new kind of metal forming process, which has been developed in recent years with a promising practical application prospect for its simple working procedure, low cost and good workpiece performance. through a lot of experiments, the optimization and chosing method of key process parameters ( pouring temperature, mold warm - up temperature, impregnating pressure, impregnating time ) has been mastered. under the precondition of appropriate chosing these parameters, the effective control of extrusion velocity is the key of mading good workpiece. but the control of extrusion velocity remains a handwork, and it is heavily affected by such uncertainties as a handler ' s knowledge and skill about the process. in order to solve the problem, the automatic control of the extrusion velocity is studied, and a computer control system is also designed under existing condition

    通過大量實驗，已掌握了關鍵工藝參數（熔液澆注溫度、擠壓模預熱溫度、浸漬時間、浸漬力）的優化選取方法。在合理選取關鍵工藝參數的前提下，擠壓速度的控制是成形出質量良好製件的關鍵。但是，目前對于擠壓速度的控制仍停留在手動控制階段，利用該工藝制備管、棒材製件的成功與否受操作者對該工藝及其設備的經驗及熟練程度等不確定因素影響很大。
  9. The study on salc includes : 1 ) the study on the harmonization between aeration rate and melts thickly rate ; 2 ) the study and application of the new multi - function composite additive ( nmca ) ; 3 ) the study on the durability of salc ; 4 ) the designation of the structure of new multi - functional unbearing compound wall and fast equipment mold, etc. the results show : the additive can improve the harmonization of the workability and mechanics characteristic of salc to a certain extent ; improve the volume stability of salc under different environment by enhancing the resistance to the freeze and thaw, dry and wet circle and drying shrinkage

    在salc的研究方面，主要包括發氣速度和稠化速度的協調性研究、新型多功能復合外加劑的研製、耐久性能的研究以及新型多功能非承重復合墻體結構及其澆注成型的快速組裝模具設計等內容；結果表明：科學合理的引入輔助外加劑在一定程度上使salc材料的工作性及相應物理力學性能得以最佳匹配，增強了salc材料對凍融循環、干濕循環及乾燥收縮的抵抗能力，使salc在不同的環境下均具有較好的體積穩定性。
  10. The scouring velocity of the molten steel against roll core is the highest and lower when the pouring angle is 15 and 90, respectively

    澆注傾角為15時，鋼液對輥芯的沖刷速度較大，而澆注傾角為90時，鋼液對輥芯的沖刷速度較小。
  11. The speed became fast at the temperature 1050. the reaction could carry completely when billets was kept in vacuum tube for 3 hours " at 1050 temperature, under the striking of great quantity of heat when the molten iron poured into the mold, the reaction was blazed rapidly and continued at a high speed. the diffusible speed of v and c was very fast because the billet was heated over 1300 in a moment, so the reaction ca n complete in a few minutes

    （ 5 ）碳化反應v + c vc在900左右開始發生，此時是固相反應，反應速度較慢，反應不能進行完全，隨溫度升高，該碳化反應的速度加快，在1050保溫3小時可以進行完全，在鑄造燒結時在過熱鐵水的巨大熱流密度沖擊下， v + c vc立即被激發，並以很快的速度進行，由於坯塊被加熱到1300以上，此時c和v擴散速度很快，因此鑄造澆注后的幾四川大學碩士學位論文分鐘內反應可以進行完全。
分享友人
分享到 Line

分享到臉書