澆注鑄型 的英文怎麼說

中文拼音 [jiāozhùzhùxíng]
澆注鑄型 英文
running castings
  • 澆 : 澆名詞（姓氏） a surname
  • 注 : Ⅰ動詞1 （灌入） pour; irrigate 2 （集中） concentrate on; fix on; focus on 3 （用文字來解釋字句）...
  • 鑄 : Ⅰ動詞（鑄造） cast; coin; make Ⅱ名詞1. （古國名） zhu, a state in the zhou dynasty2. （姓氏） a surname
  1. It can typecast wet or dry shape sand, improve the cast quality. in a word, it is a fine quality cast sand adhesives, which has the character of dilatability, cohesiveness, floatability. and gel dispersivity, repeated use

    可以澆注濕態和干態型砂，改善鑄件質量，並有良好的復用性，是一種優質的膨脹劑，黏合劑，懸浮性和膠體分散性的鑄造型砂粘結劑。
  2. The wax setting and casting process is complicate process with a series of procedures, including model creating, spruing and construction, rubber mold vulcanization and cutting, wax models injection, stone setting in wax model, wax tree creating, investing, investment mold burning - out, metal melting and pouring, casting cooling and divesting, etc

    蠟鑲鑄造是一個多工序的復雜工藝過程，包括母版製作、開設水線、製作橡膠模、製作蠟模、寶石鑲嵌到蠟模、種蠟樹、製作石膏型、石膏型脫蠟焙燒、金屬熔煉澆注、飾件冷卻清理等。
  3. The results show that the heat preservation coating and its proper thickness are favorable to the enhancement of filling mold speed of aluminium alloy ; the higher the pouring temperature is and the larger the ratio of hollow areas of vertical pouring is, the faster the speed of filling mold of aluminium alloy is ; if the mold is too thick or too thin, it may decrease the speed of filling mold ; the proper length and the area of vertical pouring are favorable to the enhancement of the speed of filling mold ; although negatire - pressure may improve filling the speed, too high negatire - pressure may enlarge the flaw in casting

    結果表明：保溫塗料及一定的塗層厚度有利於提高鋁液的充型速度；澆注溫度越高、直澆道空心面積率越大，鋁液充型速度越快；模樣厚度太厚或太薄，均會使鋁液充型速度降低；一定的直澆道長度及直澆道面積有利於提高鋁液的充型速度；施加負壓會使鋁液的充型速度大大提高，但負壓過大會增大鑄造缺陷。
  4. The influences of foundry process and method factors on combination effect was investigated including the influences of gating system design, pouring temperature, atmospheric pressure of mould cavity, thickness of cast - penetrated layer and so on

    作者就澆注系統、澆注溫度、型腔氣壓、鑄滲層厚度等工藝參數對鑄滲效果的影響進行了試驗研究。
  5. The research showed that basin is the more important feeding resource than runner in runner type gating system in lost wax casting. therefore, on the basis of the basin as feeding resource, runner and ingate as feeding channel, a new design method for runner type pouring and feeding system in investment casting was developed. the corresponding feeding mathematical pattern and allowable total weight listed for casting cluster with different basin were established after analyzing the practical feeding of basin and the calculating process for design was described in detail

    在熔模鑄造橫澆道型澆注系統中，澆口杯是比橫澆道更為重要的補縮源，因此在立足於澆口杯為補縮源、橫澆道和內澆道為澆注補縮通道的基礎上，開發了適用於熔模鑄造橫澆道型澆注補縮系統設計的新設計方法，在詳細分析了澆口杯的實際補縮情況后，建立了相應的數學補縮模式和不同澆口杯的鑄件組許用鑄件總質量表，並具體介紹了設計計算過程。
  6. The results show that, composite could be fabricated on the complicated surface by means of sodium silicate sand mold combination with vacuum infiltration process. when the substrate was 10 mm, composite layers reached 3 mm to 5 mm in thickness with high strength interface and less casting defect. microstructures of grey cast iron and low chromium cast iron matrix composites with various volume fraction has been analyzed

    結果表明：用水玻璃砂型（芯）加負壓鑄滲的工藝能夠實現復雜表面（曲面）顆粒增強復合材料的制備，澆注方式簡單可靠，基材厚度在10mm時，復合層厚度能達到3 5mm ，且復合層鑄造缺陷少，復合效果好，界面緻密而且結合強度高。
  7. The effective cost dust content of molding sand should be determined according to time factors such as the quality of the coal dust, casting size and thickness, pouring temperature, lacing sand or unit sand, and so on

    決定型砂中的有效煤粉含量應根據煤粉質量的優劣、鑄件大小和厚薄，澆注溫度、面砂或單一砂等因素。
  8. Abstract : some important principles in the design of split box molding are discussed concerning the selection of mold joint ， the methods of location and the design of gating system. it has been proved in production that the principles discussed had great effects on the cost and quality of castings

    文摘:以床身為例，討論了劈箱造型工藝設計中的幾個重要原則：包括分型面的選擇、定位方法、分芯方法及澆注系統設計等；生產實踐證明，這些原則對鑄件生產成本和品質有重要的影響。
  9. A new casting technology for inlet manifold in tilt casting machine for gravity die casting was described

    介紹了在可傾式金屬型澆注機上製造進氣歧管的鑄造新工藝。
  10. Using proper baking and pouring process for plaster mold, the castings with qualified size and good surface quality could be obtained

    在此基礎上，對工作石膏型採用合理的烘烤和澆注工藝，得到了尺寸合格、表面質量好的鑄件。
  11. In order to avoid eutectic carbide, improve nodularity, increase nodule count and increase mechanical properties, three times of inoculations were adopted in the centrifugally cast nodular iron pipes production : a ) inoculation in ladle ; 2 ) pouring stream inoculation ; 3 ) in - mold inoculation

    摘要在離心鑄造球墨鑄鐵管生產中，為防止共晶滲碳體析出，改善球化，增加石墨球數，提高力學性能，採用了三次孕育： （ 1 ）包內孕育； （ 2 ）澆注時隨流孕育； （ 3 ）型內孕育。
  12. The sand faced - iron mould casting process is a special iron castings production process, according which castings are to he cast in the iron moulds having a thin layer of the resin sand facing in their inner surfaces

    摘要鐵型覆砂鑄造是指在金屬型（鐵型）內腔覆上一薄層樹脂砂，然後採用這種覆砂鐵型澆注鑄件。
  13. The casting dimension accuracy reached ct10 class and even higher b adopting following measures : controlling foaming agent content, strictly controlling pattern manufacture, patterns welding and assembling, filling sand and moulding, as well as controlling pouring process

    採用控制發泡劑含量和嚴格模樣製作、粘結和組模工序、填砂造型工序和澆注工序中各關鍵技術措施，使產出的鑄件尺寸精度達到了ct10級以上。
  14. The technique development consists of centrifugal casting, plastic injection and extrusion etc. so as to provide customer - oriented products, improve producing efficiency and lower the cost. the small sized mc nylon bar with the diameter less than 50mm centrifugal shaping technique developed by our company is the best solution to the world difficulty in the field

    而工藝開發可以完成離心澆鑄注塑擠出等成型新工藝，為市場提供最適宜的尺寸規格，提高生產效率和降低成本公司最近研製成功的直徑小於50毫米的小規格mc尼棒材離心成型工藝，可謂解決了這個領域的世界難題。
分享友人
分享到 Line

分享到臉書