澆鑄法 的英文怎麼說

中文拼音 [jiāozhùfǎ]
澆鑄法 英文
method of casting
  • 澆 : 澆名詞（姓氏） a surname
  • 鑄 : Ⅰ動詞（鑄造） cast; coin; make Ⅱ名詞1. （古國名） zhu, a state in the zhou dynasty2. （姓氏） a surname
  • 法 : Ⅰ名詞1 （由國家制定或認可的行為規則的總稱） law 2 （方法; 方式） way; method; mode; means 3 （標...
  1. Test method for impact resistance of resin casting body

    樹脂澆鑄體沖擊試驗方法
  2. In this paper, three different kinds of polyazomethines ( pam ) / nylon 6 in situ polymerization composites were prepared using the process of monomer casting. their structures, thermal properties and also mechanical properties were analyzed

    本文利用三種聚甲亞胺的單體與尼龍6單體通過原位聚合反應，制備了三種聚甲亞胺/尼龍6原位聚合復合材料，制備工藝採用澆鑄法。
  3. Abstract : the oxidation refining method is an effective process to refine the 75 % si - fe alloy. the thermal balance of the process is calculated, which provides the theoretical basis for the possibility of the normal casting of the alloy after being refined

    文摘:氧化精煉法是硅系合金精煉技術中的一種有效方法.對75硅鐵氧化精煉過程的熱量平衡問題做了計算，討論了精煉合金滿足正常澆鑄的工藝條件
  4. Standard practice for preparing refractory concrete specimens by casting

    澆鑄法制備耐火混凝土樣件的標準實施規程
  5. Precast concrete products - test method for glass - fibre reinforced cement - cyclic weathering type test

    預澆鑄混凝土製品.玻璃纖維加強水泥試驗方法.循環氣候性試驗
  6. Using the diecast method, products with cleaner and more accurate dimensions can be produced than is the case with other casting methods

    與其它澆注法比，通過拉模鑄造製造的產品外觀更美，尺寸更精確。
  7. Preparing test specimens from basic refractory castable products by casting

    用澆鑄法從鑄制堿性耐火產品中制備試驗樣品
  8. The composite films can be prepared by in - situ polymerization processes, spin - cast from doped polyaniline / polymer solution, or by casting from polyaniline / polymer solution or dispersion

    原位聚合法、摻雜聚苯胺旋轉塗膜法和機械共混澆鑄法均可制備透明導電復合膜。
  9. It is the result of self - assembly of molecules and embodiment of dissipative structure under the imbalance state. for chondroitin sulfate ( cs ), the self - assembly behavior of cs in the presence of ca2 + is studied by afm. the result shows that cs can be formed integrated self - assembly films when its concentration exceeds 1. 0mg / ml

    實驗結果表明通過稀溶液澆鑄法可以制備具液晶性的薄膜，這種液晶結構是殼聚糖膠束顆粒在分子間的相互作用下形成的自組裝構型，是一種非平衡狀態下的耗散結構。
  10. Several kinds of inorganic solid proton conductors including zirconium phosphates, heteropolyacids ( hpa ) and hydrogen sulfates and three kinds of methods such as hybrid solid casting, exchange - precipitation process and sol - gel process which can incorporate the inorganic solid proton conductors in pems were introduced

    摘要主要介紹了目前摻雜質子交換膜用的幾種無機質子導體磷酸鋯、雜多酸、硫酸氫鹽等，並進一步介紹了將這些無機質子導體引入到聚合物中的3種摻雜方法：混合澆鑄法、離子沉澱法和溶膠凝膠法。
  11. The continuous kerbing method is ahigh production, cost effective alternative to the rpecast method. for that reason tsl construction have chosen the arrow 750xl slipformer

    連續鋪設方法取代預澆鑄方法實現高效率、低成本。因此， tsl建築公司才選擇了箭牌750xl型路緣機。
  12. Metal poured into a mold cavity during the casting process solidifies with the possibility of shrinkage, segregation or porosity, which can prevent an " as - poured " casting from being acceptable for severe applications

    在鑄造過程中，澆鑄到模腔內的金屬在凝固過程中可能會產生收縮、分離或氣孔，這些問題使得「澆鑄」鑄件無法被苛刻環境應用領域所接受。
  13. Method of test for unit mass and air content of fresh concrete by mass method

    用質量法測試新澆鑄混凝土的單位質量和空氣含量的試驗方法
  14. The generals of test methods for properties of resin casting body

    樹脂澆鑄體性能試驗方法總則
  15. Several fabrication methods, including nonwoven meshes / fiber bonding, solvent casting / particulate leaching, phase seperation / freeze drying, gas foaming and three - dimensional printing, which are used to prepare tissue engineered porous scaffolds from natural or synthetic biodegradable materials, are reviewed

    摘要綜述了以天然或合成生物降解材料為原料的組織工程多孔支架的幾種制備方法，包括無紡織物纖維粘結法、溶液澆鑄粒子洗出法、相分離凍干法、氣體成孔法和三維「印刷」等方法。
  16. Based on logistics cost optimization, the procedure of sm - cc is analyzed, and a model of order grouping is suggested and performed by self - adaptated ga

    作者研究了鋼鐵生產作業計劃的求解策略，在滿足機器約束的條件下，以澆鑄生產成本為目標，建立了澆次排序問題的數學模型，並用自適應遺傳演算法加以求解。
  17. Test method for tensile properties of resin casting body

    樹脂澆鑄體拉伸性能試驗方法
  18. When the data of logistics in current process are used for input of simulating logistics in future 100 % continuous casting process, supply of hot metal from iron - making process may not satisfy the needs of 100 % continuous casting on raw materials. because planning scheme in continuous casting process depends greatly on smelting scheme in convertor vessel, it is important for operator to balance raw materials supply, smelting and casting in order to realize the scheme of 100 % continuous casting. when some equipment are work abnormally, mixer of hot metal and lf furnace can be used for logistics buffer

    用攀鋼煉鋼生產數據對模擬軟體系統進行的測試和模擬研究結果表明：模擬系統的隨機數發生演算法可以實現對作業時間的依分佈隨機抽取；在相似的輸入條件下，模擬結果與實際生產物流的時間分佈規律基本吻合，達到了模擬軟體設計的預期目標；若以攀鋼提釩煉鋼廠現工藝的鐵水輸入作為全連鑄后的輸入條件，則現工藝的物料供應能力可能難以滿足全連鑄生產的要求；連鑄機的連澆計劃對轉爐爐次計劃的編制有很高的要求，合理安排來料、煉鋼與澆鑄三者間的物流平衡關系將是保證全連鑄作業的重要條件；當出現設備異常情況時，可以利用混鐵爐與lf爐站前等待作為物流緩沖池，通過延長系統的平均物流時間來緩解因設備檢修和故障等擾動所造成的影響，確保生產的順利進行。
  19. Test method for embedment stress caused by casting compounds on glass - encased electronic components

    玻璃封裝電子器件受澆鑄化合物所引起的灌封應力的試驗方法
  20. Unsaturated polyester resin - determination of stability of casting resin in basic solution

    不飽和聚酯樹脂澆鑄體耐堿性測定方法
分享友人
分享到 Line

分享到臉書