焊接的熔深 的英文怎麼說

中文拼音 [hànjiēderóngshēn]
焊接的熔深 英文
penetration
  • 焊 : 動詞（用熔化的金屬修補金屬器物或使金屬工件連接起來） weld; solder
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  • 的 : 4次方是 The fourth power of 2 is direction
  • 熔 : 動詞（熔化） melt; fuse; smelt
  • 深 : Ⅰ形容詞1 （從上到下或從外到里的距離大） deep 2 （深奧） difficult; profound 3 （深刻; 深入） thor...
  • 焊接 : weld; welding; soldering; seal; sealing; sealing-in; shutting together
  1. Schauer d a. thermal and dynamic effects in electron beam welding cavities [ m ]. america : university of claifornia, 1977

    吳會強，馮吉才，何景山.電子束焊接深熔產生機理的研究現狀與發展.焊接， 2003 （ 8 ）
  2. Meanwhile it retains evenness on lift force to prevent leakage of residue that is caused by installation clearance error or changes in welding criteria, flow off molten iron as well as break - over welding, so that the ideal fosion depth and finishment have been fulfilled

    在需原動力的條件下，該機利用彈性夾角變化，隨著筒體轉動，使墊層焊劑始終緊貼筒體外側環向焊接區，並保持托力均勻防止因裝配間隙誤差或焊接規范變化而引起漏渣，鐵水下淌及焊穿現象，達到理想的熔深度和光潔度。
  3. The dcep mig has the characteristic of deeper penetration which can reduce defective fusion and good arc stabilization. the dcen mig has the characteristic of shallow penetration of welding seam, and the welding wire has a high melting speed. so the variable polarity pulsed mig is a new technology for the welding of aluminium alloy sheet

    變極性脈沖mig焊是一種新的焊接工藝方法，其綜合了dcep脈沖mig焊熔深較大、可以減少焊縫的熔合不良、電弧穩定性好和dcenmig焊焊縫熔深淺、焊絲熔化速度較快的特點，減小了焊縫的熔深，增加了焊絲的熔化速度，是一種適合於薄板鋁合金焊接的新方法。
  4. So the effective autocontrol to the penetration of welding needs to be settled in co _ 2 gas shield arc welding process

    因此， co _ 2氣體保護焊焊接過程中，有效地實施對焊接熔深的自動控制是需要解決的問題。
  5. The lack of the penetration of welding bead is a typical defect. it will do great harm to the quality and safety of the welding structure

    焊縫熔深不足是焊縫及焊接接頭內部的一個典型缺陷，會給焊接結構的質量及使用安全帶來危害及影響。
  6. The effect of the changes of the wire extension on the penetration of welding bead is analyzed and a project of the controlling to the penetration of welding bead is established in this paper

    本文分析了焊接過程中由於干伸長的變化對焊縫熔深的影響，確定了熔深控制方案。
  7. The penetration of welding bead is hard to be checked directly in practice, so the control on the penetration of welding bead is mainly realized by adjusting the related factors

    由於焊縫熔深在實時狀態下難以直接檢測，因此，對焊縫熔深的控制主要是通過調節與其相關量來實現的。
  8. When the welding current is added, the quality of heat of the arc will increase, so both the volume of molten puddle and the depth of arc crater will all increase, and the weld depth will increase when the weld is cooling

    焊接電流增加時，電弧的熱量增加，因此熔池體積和弧坑深度都隨電流增加，所以冷卻下來后，焊縫厚度就增加。
分享友人
分享到 Line

分享到臉書