焊接線 的英文怎麼說
中文拼音 [hànjiēxiàn]
焊接線
英文
adherent wire-
Three lead wires are soldered to the anchor terminals.
在固定接線端子上焊有三根導線。5 welding by patchcord between the high unit and the low unit, and the unit body can circumgyrate 180, convenient for the cable welding
5高低端單元之間用跳線焊接,單元體可旋轉180 ,方便電纜焊接Uses : cold welding of nonferrous metals such as cu al ag ni pt sn zn ta and some of their alloys
產品用途:對銅、鋁、金、銀、鉑、錫。鉭鈮等有色金屬線材及他們部分合金線材的焊接。Cell connectors and terminal post burning must be done in such a manner that there is complete fusion of the post strap top and the cover lead bushing with the connector ring or terminal post.
連接條和接線柱的焊接必須使極柱頂部和蓋子的鉛襯套與連接條環口或接線柱完全熔焊牢固。A resistance meander wire usually of constantan is welded onto a strip of foil
在金屬薄片上焊接了改良的電阻導線,通常使用的是康銅導線。Radiographic examination of fusion welded joints in metallic materials
金屬熔化焊焊接接頭射線照相Long rails in jointless track are usually made on welded rail site or in railway welded rail factory
摘要無縫線路長鋼軌道常由鐵路焊軌廠或現場焊軌基地焊接。Microstructure and toughness of welding coarse - grain heat affected zone in ti - v - nb microalloy pipeline steel
微合金管線鋼焊接粗晶區組織及韌性Idea of differential plane is introduced in the calculation of orientation of normal line, and optimal orientation for electron gun is obtained. this work is helpful for guaranteeing welding quality
在法線姿態的計算中,引入微分平面的設計思想,獲得了焊接過程中的最佳姿態,保證了焊縫質量。The steel construction is made up of roof beam, post, purlin, roofing and wall, adopt the automatic production line to weld and take shape in the factory, construction site spend high - strength bolted joint reduce weld work load, make progress and quality receive the complete assurance
鋼結構由梁、柱、檁條、屋面和墻體組成,工廠內採用自動化生產線焊接成形,施工現場用高強螺栓連接,減少了焊接工作量,使進度和質量得到完全保證。The welding technology of francis turbine runners is optimized from the view of subsection welding and local heating by numerical simulation. the result shows that welding residual tensile stress appears in the weld and its area nearby, and peak stress appears in the dangerous area of blades after practising quondam welding technology ; welding residual tensile peak stress in the dangerous area of blades can be decreased by welding both ends earlier and then welding middle section later during subsection welding, and decreasing effect on welding residual stress of the subsection welding is related to the weld length of blade outlets and welding direction of each subsection ; decreasing effect on residual stress of the local heating is direct proportional to heating time, heating temperature, heating area, and inversely proportional to cooling area, and welding residual tensile peak stress in the dangerous area is decreasing trend earlier, and then increasing trend later with heated location increased
本文利用數值模擬手段對轉輪的焊接工藝從分段焊和局部加熱兩個方面進行了優化,結果表明:採用普通工藝焊接時,葉片焊后殘余拉應力出現在焊縫及其附近區域,並且在葉片出水邊的熔合線附近(危險區域)出現了峰值;在採用優化的分段焊時,先焊兩端后焊中間的方法可以降低葉片危險區域的焊接殘余拉應力峰值,降低效果與葉片出水邊焊段長度、焊縫各段的焊接方向有關;局部加熱法降低轉輪危險區域殘余應力的效果主要與加熱時間、加熱溫度以及加熱面積成正比,與冷卻面積成反比,並且危險區域的殘余應力隨加熱區域的增大呈先降低后升高的趨勢。Standard reference radiographs for examination of aluminum fusion welds
用於檢驗焊接中鋁的標準參考射線照片Influence of welding line energy on microstructure formation of deposited metal
焊接線能量對熔敷金屬組織形成的影響Specification for the design, testing, and utilization of welded - wire rack decking
焊接線架蓋板的設計檢驗和利用規范Butt weld neon la.
電焊接氖燈焊接線氖燈Welding energy definition : if the welding energy definition is larger, the welding deformation will be larger too
焊接線能量:焊接線能量越大,焊接變形越大。Minimal the tendency of microcracks can be obtained by improving the shape of weld pool and enhancing the welding energy input
通過改善焊縫成形和提高焊接線能量有助於減小兩類熱影響區微裂紋傾向。Currently the company has two manufacturing production line, a motor production line, the chassis welding lines, large cast production line
目前公司具有兩條整車生產線一條發動機生產線車架焊接線大型注塑生產線等。Different types, size and colors wires can be used to connect with neon lamps as per customer s demand, as well as the terminals
焊接線氖燈加引線氖燈可根據客戶要求配各種顏色以及型號電線,同時尾線可接各種規格端子。Copper and aluminum unified core or all copper core : header pipe diameter up to 22mm or 25mm, few welding line, high intension, and strong pressure resistance
板芯以銅鋁復合為主或全銅,集熱管直徑達22mm或25mm ,無焊接線,高效能,強承壓。分享友人