焊接順序 的英文怎麼說

中文拼音 [hànjiēshùnxù]
焊接順序 英文
sequence of welding
  • 焊 : 動詞（用熔化的金屬修補金屬器物或使金屬工件連接起來） weld; solder
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  • 順 : Ⅰ介詞1 （向著同一個方向） in the same direction as; with 2 （依著自然情勢; 沿著） along; in the d...
  • 焊接 : weld; welding; soldering; seal; sealing; sealing-in; shutting together
  • 順序 : 1. （次序） plain sequence; subsequence; order; sequence; succession2. （順著次序） in proper order; in turn
  1. As an application of this fem preprocessing system, the simulation on the welding process of missile ’ s oil box was performed, in which the effects of the welding sequences of four web plates and welds on each web plate are primarily analyzed. the simulation results show that the deformations under varied welding sequences are almost the same. downward deflection deformation is obtained along the weld longitudinal direction in the structure as well as upward deflection deformation along the weld traverse direction

    對于某型號導彈油箱結構焊接過程的數值模擬計算，主要考察了每塊立板上各段焊縫焊接順序的調整、四塊立板之間不同的焊接順序以及焊接起始端的選擇對結構焊后變形的影響規律，模擬結果表明:壁板在各種焊接順序下的整體變形規律基本相似，即焊後壁板沿焊縫縱向發生了向下的撓曲變形，中部向下變形量最大;沿焊縫橫向發生了向上的撓曲變形，壁板兩端部變形量較大，且壁板前端變形大於壁板後端。
  2. The design process of the proposed method is described as follows : the user inputs the 3d sketch of a welded machine, and the geometry and topology information of the members in the welded machine are established automatically. the design information is acquired by the means of man - computer interaction. according to the knowledge of design and welding, the rules of bar orientation, joint processing and welding sequence are established

    用戶在autocad中輸入焊接機架的線框簡圖，提取出機架結構的幾何和拓撲信息，然後通過人機交互輸入設計信息，並根據機架的設計知識與焊接知識，建立機架的桿件方位布置規則、節點處理規則與焊接順序自動確定規則，最後在autocad中生成經過節點處理的機架三維實體，並提供一套合理的焊接順序。
  3. Welding position : if the configuration collocation of weld is symmetry and the welding sequence is reasonable, the longitudinal contraction and transverse lateral contraction deformation are usually produced, incontrast, the bending deformation is usually produced

    焊接位置：如果焊縫在結構布置對稱，焊接順序合理時，則主要產生縱向收縮和橫向收縮變形，反之，則要發生彎曲變形。
  4. Assembly ? welding sequence : the configuration which had been whole assembled can decrease welding deformation for configuration rigidity had been added

    裝配?焊接順序：將結構總裝后進行焊接，由於結構剛性增加，可以減少焊后變形。
  5. Abstract : in the article, some special installing methods of steel - pipe concrete column and steel structure of shenzhen saiger plaza, including installing sequence, measurement, correction, and welding, are introduced

    文摘:介紹深圳賽格廣場鋼管混凝土柱?鋼結構在結構安裝方面的特殊做法，包括安裝順序、測量、校正和焊接等。
  6. Different assembly ? welding sequence may result different risidual deformation, we usually take fixup by spot welding first, then take welding symmetrically

    不同的裝配?焊接順序，焊后產生不同的殘余變形，一般是先點固，再進行對稱焊接。
  7. Factors including welding sequence being input of the network, and welding distortions being output can make the resulting network which is used for the model of welding distortion and its fast forecasting

    以焊接順序等因素作為網路輸入，以鋼結構板材凹凸變形為輸出，訓練生成網路焊接變形模型，可用於預測船舶鋼結構焊接變形量的快速預測。
  8. This system can be used in other plane welding when working with the corresponding jig and rational welding craft arrangement, and this makes numerical welding machine becomes more efficient and flexible by changing nc codes according to different welding path and resolves the contradiction between process automation and process cost in some extent

    通過配合相應的夾具，合理的焊接工藝安排順序，該系統可以應用於其他平面焊接加工場合，數控焊機可以並根據焊接軌跡及時更改加工代碼，提高設備的焊接適應性和焊接效率，一定程度上解決了自動化成本和加工效率之間的矛盾。
  9. 3 according to analysis on the reason for failure of joints, improved measures for new joints are presented, the following phases are included, improved butt welding design, improved technology and welding sequence for butt welding seam, intensive strength checking for butt welding seam, intensive quality inspection for butt welding seam

    （三）通過對節點破壞成因的分析，提出了新型節點的改進措施，包括四個方面：改進對接焊縫的設計、改進對接焊縫的焊接工藝和焊接順序、加強對接焊縫的強度校核、加強對接焊縫的質量檢測。
  10. The minimal deformation of the structure is obtained using the method presented as follows : four web plates are first tack welded on both ends, and then the web plates are

    採用設計的焊接順序在導彈油箱壁板實際結構上進行焊接並對焊後壁板變形進行了測量，測量所得的壁板變形規律與模擬計算結果吻合良好。
  11. A design approach to the 3d cad of welded machine is presented in this thesis, in which the rules of bar orientation, joint processing and welding sequence are stressed

    本文提出了一個面向焊接機架的三維cad方法，著重研究混合型鋼結構的桿件布置、節點處理和焊接順序自動生成方法。
分享友人
分享到 Line

分享到臉書