焊接飛濺 的英文怎麼說

中文拼音 [hànjiēfēijiàn]
焊接飛濺 英文
weld spatter
  • 焊 : 動詞（用熔化的金屬修補金屬器物或使金屬工件連接起來） weld; solder
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  • 飛 : Ⅰ動詞1 （鳥、蟲等在空中活動） fly; flit 2 （利用動力機械在空中行動） fly 3 （在空中飄浮遊動） fly...
  • 濺 : 動詞（液體受沖擊向四外射出） splash; spatter
  • 焊接 : weld; welding; soldering; seal; sealing; sealing-in; shutting together
  • 飛濺 : splash; gabble; sparging; spatter; spattering; spray; spill
  1. Igbt power modules, 25khz inverterfrequency, fast response time, high arc stability, almost spatter - free welding

    採用igbt模塊，逆變頻率達25khz ，動態響應速度快，穩弧性能好，焊接飛濺極小。
  2. Igbt power modules, 18khz inverter frequency, fast response time, high arc stability, almost spatter - free welding

    採用igbt模塊，逆變頻率達18khz ，動態響應速度快、穩定性能好、焊接飛濺極小。
  3. The algorithm of image processing is the key. due to anomalous welding seam, the intensive arc light, random breaking of the bubble and gathering of the gas in the welding area, the seam images captured contain a lot of noise. in this case the noise must be removed and the welding seam is positioned accurately

    本系統的圖像處理部分採用了ccd攝像頭和視頻捕獲卡，圖像處理的演算法是最關鍵的部分，由於焊縫圖像並不是十分規則，而且在焊接時還會受到強烈弧光、飛濺和工件表面狀況的影響，因此在這種情況下，必須有效的排除干擾把焊縫的中心位置準確找出來。
  4. Specially for welding of thin and mid - thickness steel ; suitable for mag co2 welding of low carbon steel and low alloy steel inner wire feeder structure ; zx5 series thyristor dc arc welder ac arc welder with single phase moveable coil for sma mma welding ; suitable for welding low carbon steel, low alloy steel ; suitable for welding mid - thickness steel

    可用於所有牌號焊條的直接手工電弧焊接引弧容易，無須用戶調節可遠距離調節焊接電流，便於焊工操作焊機動特性好，性能柔和，電弧穩定焊接熔池平靜，飛濺小，不咬邊，焊縫成形美觀。
  5. Use a blast cleaner or power tool to remove weld flux slag, weld metal spatters, weld flux fume deposits, rust and damaged paint film in welded areas

    通過噴砂或電動工具除去焊渣、飛濺焊煙、銹跡和焊接部損壞的漆膜。
  6. Transitional feature of the arc and metal droplet in the welding process with steam shielded arc is investigated by means of analysing the waveforms of welding voltage and current under different welding regimes and it is found that there are two types of arc process behavor ? " arc starting - arc blowing out - short - circuiting " and " arc - starting - short - circuiting ". under the condition of constant diameter of welding wire and its feeding speed, the arc process behavor can be changed by adjusting the inductance of welding circuit as well as the voltage of power supply. if arc process behaves as alternative process of " arc starting - arc blowing out - short - circuiting " with minimum time duration of arc blowing out and maximum frequency of short - circuit transition, the welding process will be stable with less spatter and smooth weld bead

    通過分析不同焊接規范下的焊接電壓和電流的波形.研究了水蒸氣保護下電弧及熔滴過渡的特點，發現其電弧過程行為有「燃弧?熄弧?短路」和「燃弧?短路」兩種形式.在焊絲直徑和送絲速度一定的情況下，通過調節焊接迴路中的電感量和電源電壓，可以改變電弧的過程行為形式.若電弧過程呈「燃弧?熄弧?短路」交替進行，並且熄弧時間最短時，短路過渡頻率最高，在這種情況下，飛濺小，焊道成型好，焊接過程穩定
  7. Welding experiments prove that focusing mirror is well protected when such a crossjet is used

    實際的焊接試驗證明這種結構的噴嘴可以有效吹除飛濺，保護聚焦透鏡。
  8. Patent control technology of dynamic characteristics and waveform, hard arc, stable welding current, little spatter, good welding surface, optimized matching parameters, welding speed increased by 100 - 200 %

    專利動特性及波控技術，電弧挺度大，焊接過程穩定，飛濺少，成型美觀，優化參數匹配，焊速可提高100 - 200 %
  9. Self adjust function of electric arc, easy arc igniton, less spatters, perfect weld appearance

    電弧自調節能力強，引弧成功率高，焊接飛濺小，熔敷率高，焊縫成形美觀。
  10. Leaving the valve in a fully closed position helps prevent weld spatter from falling directly onto the mating faces of the seats

    保持閥門處于完全關閉狀態，有助於防止焊花飛濺直接落到閥座連接面上。
  11. Optimized control of dynamic and static characteristics, strong adaptability for electricity network, fast dynamic response, stable welding current, little spatter, good welding surface

    優化動靜特性控制，抗網電波動能力強，動態特性優良，焊接過程穩定，飛濺少，成形好
  12. Answer : ( 1 ) prevent to splatter the metal is caused burnable with fire ; ( 2 ) avoid the harm of electric arc ray radiation to human body ; ( 3 ) prevent certain and harmful gas toxic ; ( 4 ) soldering when pressure vessel, should prevent to solder produce explosion ; ( 5 ) when headroom works, want to take safety belt and safety helmet ; ( 6 ) the attention prevents accident getting an electric shock

    答： （ 1 ）防止飛濺金屬造成灼傷和火災； （ 2 ）防止電弧光輻射對人體的危害； （ 3 ）防止某些有害氣體中毒； （ 4 ）在焊接壓力容器時，要防止焊接發生爆炸； （ 5 ）高空作業時，要帶安全帶和安全帽； （ 6 ）注重避免觸電事故。
分享友人
分享到 Line

分享到臉書