焊的 的英文怎麼說
中文拼音 [hànde]
焊的
英文
welded-
The etched section also reveals that multiple weld passes were made over the top of the original submerged arc weld pass.
從酸蝕斷面還可以看出：在原自動埋弧焊的上面覆蓋有多層焊道。Recommended practices for gas - tungsten - arc welding
鎢電極惰性氣體保護焊的推薦規范Hard metal tipped tools, well suitable for brazing
適用於硬焊的硬金屬尖端工具。Pre - data gathering module achieves the collection and communication of sixteen - route temperature signal. speed measuring and controlling module realizes the control of refolw soldering transfer speed by manipulating transducer. on - off outputting module fulfills calefaction control of calefaction tube by solid state relay. above position operator software programs by delphi, and realizes pid parameter automatic timing and no - oversnooting temperature control. software has friendly interface, convenient operation, complete functions
前置數據採集模塊完成16路溫度信號的採集和通訊；速度測量模塊與速度控制模塊通過控制變頻器來調節迴流焊的傳輸速度；開關量輸出模塊通過固態繼電器對加熱管進行控制；上位機軟體採用delphi編程，實現了pid參數自整定以及無超調的溫度控制。Welding. studs and ceramic ferrules for arc stud welding
焊接.螺柱弧焊的螺柱和陶瓷箍Non - destructive examination of fusion welds. visual examination
熔焊的無損檢驗.外觀檢查Quite a bit of heat is needed, due to the thickness of the copper pipe, and an electrical soldering iron probably won ' t be able to deliver sufficent heat
因為銅管有一定的百度，所以有可能錫焊的溫度不夠，它對溫度的要求是比較高的。Generally, intensity of welds in fsw exceeds heat affected zone
通常情況下，摩擦攪拌焊的焊縫強度超過熱影響區。Figure 7 : tail or crescent bond is the shape of the thermosonic bond on the substrate ( ball bond is on dimensions are shown in the box to the right of the figure
月牙形焊接（熱超聲焊的末端）的尺寸和形狀直接與引線直徑和毛細管的幾何形狀有關。Figure 6 : drawing3 showing wedge bonding operation on the second bond, at the substrate bondinger. figure 7 : tail or crescent bond is the shape of the thermosonic bond on the substrate ( ball bond is onthe die side )
月牙形焊接（熱超聲焊的末端）的尺寸和形狀直接與引線直徑和毛細管的幾何形狀有關。Asme boiler pressure vessel code - section 9 : welding and brazing qualifications
Asme鍋爐和壓力容器規則.第9節:焊接和釬焊的資格要求In order to study the characteristic signals according to the quality of the welding with dissimilar gaps, the self - made real - time monitoring system with coaxial sensors is applied to acquire and extract coaxial signal, and then the signals are analyzed with modes analysis, subsection power analysis and wavelet analysis
摘要為了研究不同間隙下激光拼焊的焊縫質量及其對應的信號特徵，採用自製同軸傳感系統採集提取多種間隙下焊接時的同軸光信號，並對信號進行眾數分析、分段功率譜分析和小波分析。Direct metal forming based on plasma arc welding is a novel rapid prototyping process
摘要基於等離子弧焊的直接金屬成形方法是一種新型的快速成形工藝。Examination of the density, strength, hardness and microstructure showed that the mechanical properties and structure of the part made by direct metal forming process are better than that obtained from selective laser sintering process, as good as or even better than castings
對成形件進行的密度、強度和硬度指標測試和金相組織觀察表明：基於弧焊的直接金屬成形件的組織結構和力學性能指標明顯優于選擇性激光燒結工藝成形件，達到或高於鑄造零件。Qualification testing of welders for under - water welding - part 1 : diver - welders for hyperbaric wet welding
水下焊接焊工資格測檢.第部分：高壓濕焊的潛水焊工Qualification testing of welders for under - waster welding - part 2 : diver - welders and welding operators for hyperbaric dry welding
水下焊接焊工的資格測驗.第2部分：高壓干焊的潛水焊工和焊接操作者Recommended practices for electron beam welding
電子束焊的推薦性實施規范The application of stainless steel argon arc welding of no full argon in pipe
管內不充氬不銹鋼氬弧焊的推廣應用Resistance spot and seam welding process for aerospace use
航空航天用接觸點焊及滾焊的焊接工藝Vickers hardness testing of resistance spot, projection and seam welds low load and microhardness
電阻點焊凸焊和滾焊的維氏硬度試驗分享友人