焊縫向 的英文怎麼說

中文拼音 [hànféngxiàng]
焊縫向 英文
welding course
  • 焊 : 動詞（用熔化的金屬修補金屬器物或使金屬工件連接起來） weld; solder
  • 縫 : 縫名詞1. （接合處） seam 2. （縫隙） crack; crevice; fissure; slit
  1. This indicated that the fracture had initiated at the unfused butt weld in the longitudinal stiffener.

    研究表明裂紋是從縱向加勁助未熔透的對接焊縫中起始的。
  2. In addition to, the fatigue crack between web and upper flange of welded steel crane beam on heavy duty service was discussed, and based on long - term observation and research, the author classified fatigue crack into bearing type and middle type crack along the horizontal direction. the causation, distributive law and mechanism of the crack were analyzed, and the precautions to take and the measures to remedy crack were presented. the main defacts including damage, crack, erosion and aging in structures, especially in concrete structure were introduced ; the defact mechanism was analyzed and the precautions to take were also given

    另外，作者對重級工作制焊接鋼吊車梁腹板與上翼緣連接焊縫的縱向水平疲勞裂縫進行了長期的觀察和研究，根據疲勞裂縫產生的不同機理，將其分為支點裂縫和肋間裂縫，並討論了兩類裂縫產生的原因、分佈規律、機理以及防治的措施；對工程中經常遇到的結構構件，尤其混凝土構件的幾種主要病害（損傷、裂縫、腐蝕與老化）進行了機理分析並提出了防治措施。
  3. As an application of this fem preprocessing system, the simulation on the welding process of missile ’ s oil box was performed, in which the effects of the welding sequences of four web plates and welds on each web plate are primarily analyzed. the simulation results show that the deformations under varied welding sequences are almost the same. downward deflection deformation is obtained along the weld longitudinal direction in the structure as well as upward deflection deformation along the weld traverse direction

    對于某型號導彈油箱結構焊接過程的數值模擬計算，主要考察了每塊立板上各段焊縫焊接順序的調整、四塊立板之間不同的焊接順序以及焊接起始端的選擇對結構焊后變形的影響規律，模擬結果表明:壁板在各種焊接順序下的整體變形規律基本相似，即焊後壁板沿焊縫縱向發生了向下的撓曲變形，中部向下變形量最大;沿焊縫橫向發生了向上的撓曲變形，壁板兩端部變形量較大，且壁板前端變形大於壁板後端。
  4. The welding technology of francis turbine runners is optimized from the view of subsection welding and local heating by numerical simulation. the result shows that welding residual tensile stress appears in the weld and its area nearby, and peak stress appears in the dangerous area of blades after practising quondam welding technology ; welding residual tensile peak stress in the dangerous area of blades can be decreased by welding both ends earlier and then welding middle section later during subsection welding, and decreasing effect on welding residual stress of the subsection welding is related to the weld length of blade outlets and welding direction of each subsection ; decreasing effect on residual stress of the local heating is direct proportional to heating time, heating temperature, heating area, and inversely proportional to cooling area, and welding residual tensile peak stress in the dangerous area is decreasing trend earlier, and then increasing trend later with heated location increased

    本文利用數值模擬手段對轉輪的焊接工藝從分段焊和局部加熱兩個方面進行了優化，結果表明:採用普通工藝焊接時，葉片焊后殘余拉應力出現在焊縫及其附近區域，並且在葉片出水邊的熔合線附近（危險區域）出現了峰值;在採用優化的分段焊時，先焊兩端后焊中間的方法可以降低葉片危險區域的焊接殘余拉應力峰值，降低效果與葉片出水邊焊段長度、焊縫各段的焊接方向有關;局部加熱法降低轉輪危險區域殘余應力的效果主要與加熱時間、加熱溫度以及加熱面積成正比，與冷卻面積成反比，並且危險區域的殘余應力隨加熱區域的增大呈先降低后升高的趨勢。
  5. Vertical welds not completely removed by backgouging shall be performed vertically up, unless specifically approved in writing by secco

    對于不能通過逆向刨削完全清除的縱向焊縫應垂直施焊，除非賽科公司有特殊的書面指示不用垂直施焊。
  6. Test method for guided bend test for ductility of welds

    焊縫韌性的定向彎曲試驗方法
  7. Often lack of fusion adjacent to the girder web in the transverse groove welds led to the cracking.

    在靠近主梁腹板的橫向坡口焊縫處常常出現未熔透而導致裂紋。
  8. Based on the 3d geometry vision, using java3d, for each of worktable and sine welding seam part of sheet, the ve modeling experiments achieve the construct of macrostructure, security virtual thickness and virtual guide based on error, and accomplish the space restriction of robot running. via the structured laser sensor ’ s getting three - dimension information, the experiments achieve the modeling of sine welding seam part of sheet by using programming

    在立體視覺傳感系統獲得三維信息的基礎上，利用java3d建模技術，分別對工作臺、薄板正弦曲線焊縫工件進行建模實驗，完成了虛擬環境中宏觀環境模型的建立，並根據誤差建立了安全虛擬厚度和虛擬向導，完成了對機器人運動的空間約束;通過結構光傳感器獲得三維信息，編程實現對薄板正弦曲線焊縫模型的建立。
  9. Welding position : if the configuration collocation of weld is symmetry and the welding sequence is reasonable, the longitudinal contraction and transverse lateral contraction deformation are usually produced, incontrast, the bending deformation is usually produced

    焊接位置：如果焊縫在結構布置對稱，焊接順序合理時，則主要產生縱向收縮和橫向收縮變形，反之，則要發生彎曲變形。
  10. Non - destructive testing of steel tubes - automatic ultrasonic testing of the weld seam of electric welded steel tubes for the detection of longitudinal imperfections

    鋼管的無損試驗.縱向缺陷探測用電焊鋼管焊縫的自動超聲波檢驗
  11. Pipes and fittings of longitudinally welded hot - dip galvanized steel pipes with spigot and socket for waste water systems - part 2 : dimensions ; german version en 1123 - 2 : 1999

    帶插接套管廢水管道.縱向焊縫熱鍍鋅鋼管道和管件.第2
  12. Pipes and fittings of longitudinally welded stainless steel pipes with spigot and socket for waste water systems - part 3 : system x ; dimensions ; german version en 1124 - 3 : 1999

    帶插接套管廢水管道.縱向焊縫不銹鋼製造管和管件.第3
  13. Pipes and fittings of longitudinally welded stainless steel pipes, with spigot and socket for waste water systems - part 2 : systeme s ; dimensions ; german version en 1124 - 2 : 1999

    帶插接套管廢水管道.縱向焊縫不銹鋼製造管和管件.第2
  14. Standard specification for steel line pipe, black, plain end, longitudinal and helical seam, double submerged - arc welded

    雙埋弧焊縱向和螺旋焊縫平頭無鍍層鋼制總管的標準規范
  15. The other way, theoretical analysis of weld tracking system with a leading sensor is stated, based on the analyzing of movement process of the tracking system, a loop control structure diagram is presented, the deuce vision feedback system is used and realized the repeated and automatic tracking in multiplayer seam and controlling of system of tracking and system of motion

    同時就傳感器超前檢測式焊縫自動跟蹤系統進行了深入的理論分析，在分析該系統跟蹤過程運動關系的基礎上，建立了系統的閉環控制關系圖，並提出了其系統數學離散控制結構簡化圖。採用兩點式視覺伺服反饋系統，實現機器人在多層多道焊接時的重復自動跟蹤以及跟蹤機構的控制和焊炬橫向調節機構的控制，並使之協調聯動，滿足焊接過程的要求。
  16. 1 process - oriented algorithms for sheet metal deployment. an investigation is made on the constrains to welded seam, sheet thickness, slope type and their influences to sheet metal manufacture process, and a rational method is adopted to treat design and calculation

    本文主要涉及的研究內容及創新點包括以下幾個方面： 1 、提出並實現了面向工藝的鈑金展開演算法；探討了展開計算時焊縫邊界約束條件，板厚處理，坡口型式對鈑金加工製造工藝的影響，並採用合理的方法進行處理和設計。
  17. Minimal the tendency of microcracks can be obtained by improving the shape of weld pool and enhancing the welding energy input

    通過改善焊縫成形和提高焊接線能量有助於減小兩類熱影響區微裂紋傾向。
  18. The opening stress and the life of crack growth is calculated and compared with the test results and the experience formula. the feasibility of the newman theory of opening stress used in the high strength steel is validated. then through the slice synthesis method, the three dimension surface crack of the weld joint of cone - cylinder is decomposed into many plane through cracks

    本文將基於裂紋閉合現象建立的帶狀屈服模型，用在平面貫穿裂紋中，計算此時的裂紋張開應力和疲勞裂紋擴展壽命，與試驗結果和經驗公式比較，驗證newman裂紋張開應力理論在高強鋼中的可行性；然後，用切片合成法，把潛艇結構凸錐柱結合殼焊縫處的三維表面裂紋分解成平面貫穿裂紋，用帶狀屈服模型的理論來分析平面貫穿裂紋，得到裂紋沿深度方向的擴展速率，進而得到潛艇結構的疲勞壽命。
  19. Transverse / cross / lateral contraction deformation ： the component contracts in the upright direction of weld after weiding

    橫向收縮變形：構件焊后在垂直焊縫方向上發生的收縮。
  20. Petroleum and natural gas industries. non - destructive testing methods of steel tubers for pressure purposes. ultrasonic testing of the weld seam of elcctric resistance and induction welded steel tubes for the detection of longitudinal imperfections

    石油天然氣工業.承壓鋼管無損檢測方法.電阻焊和感應焊鋼管焊縫縱向缺欠的超聲波檢測
分享友人
分享到 Line

分享到臉書