焊縫成形 的英文怎麼說

中文拼音 [hànféngchéngxíng]
焊縫成形 英文
appearance of weld
  • 焊 : 動詞（用熔化的金屬修補金屬器物或使金屬工件連接起來） weld; solder
  • 縫 : 縫名詞1. （接合處） seam 2. （縫隙） crack; crevice; fissure; slit
  • 成 : Ⅰ動詞1 （完成; 成功） accomplish; succeed 2 （成為; 變為） become; turn into 3 （成全） help comp...
  1. A kind of stainless steel flux - cored wire has been successfully developed, based on acid slag type system, by adding a bit of oxides and trace of deoxidizer, adjusting the fluidity of melting slag to increase shielding of the back weld

    在酸性渣系的基礎上，通過添加少量氧化物，調整熔渣的流動性，並加入微量的強脫氧劑，以增強背面焊縫的保護，研製成功一種背面不充氬的不銹鋼打底單面焊雙面成形專用藥芯焊絲。
  2. Tailor - welded tube in hydroforming and influence of the heat affected zone on bulge forming

    焊縫管液壓成形技術及熱影響區對成形的影響
  3. Thus the fracture likely initiated from fatigue sharpened cracks originating from slag and void in the plug welds.

    因此，斷裂可能是由於從塞焊焊縫內的焊渣和氣孔外形成的尖銳的疲勞裂紋而產生的。
  4. It is drawn seamless tubing, which can be welded to join the tubes of the bike frame together. the tubes are cold worked to provide additional strength to the material, and through this process is tailored to provide the correct shape tubing for the frame design

    由ti 3al2 . 5v製成的鈦合金車架採用無縫管材的焊接技術，其管材經冷軋成形后經過嚴格地挑選檢驗，以保證其材料的強度和質量。
  5. Abstract : a manufacture method of a major diameter circline weldless u - expansion joint by hydrostratic forming is introduced, a calculation formula of loading with hydrostratic forming is given by stress analysis

    文摘:簡要介紹了液壓成型大直徑無環焊縫u形膨脹節的方法，通過應力分析，給出了液壓成型的加載內壓計算公式。
  6. 9 series pressure cavity is made of stainless steel single unit integration structure by processing so may guarantee for the better seal performance. the characteristic of product are no o - ring, no welded, no silicon oil or other organic, structural durability ; the most apply to pump and compressor, liquid pressure and pneumatic system, go - anywhere vehicle, energy and water processing system, pressure instrument, refrigerating equipment, agricultural machinery device, locomotive braking system

    9系列壓力腔採用不銹鋼單件一體式結構加工而成，因而可以保證較好的密封性能， 9系列產品的特點是無o形圈無焊縫無硅油或其它的有機物，經久耐用，主要應用於泵及壓縮機，液壓及氣動系統越野車能源及水處理系統壓力儀表冷凍設備農機設備機車剎車系統。
  7. Specially for welding of thin and mid - thickness steel ; suitable for mag co2 welding of low carbon steel and low alloy steel inner wire feeder structure ; zx5 series thyristor dc arc welder ac arc welder with single phase moveable coil for sma mma welding ; suitable for welding low carbon steel, low alloy steel ; suitable for welding mid - thickness steel

    可用於所有牌號焊條的直接手工電弧焊接引弧容易，無須用戶調節可遠距離調節焊接電流，便於焊工操作焊機動特性好，性能柔和，電弧穩定焊接熔池平靜，飛濺小，不咬邊，焊縫成形美觀。
  8. The explosive welding specimen were also annealed in vacuum at various elevated temperature from 1000 to 1300. optic microscope, sem, tem and eds ( electron diffraction scattering ) techniques are applied to observe the microstructure and the element profiles of the welding interface and the interdiffused layer, reveal the interdiffused performance of alloy elements at elevated temperature, and analyze the structure and composition of the precipitated phases. moreover, the tensile strength of welding line with the two different techniques and various welding parameters were carried out

    採用金相、掃描電鏡、透射電鏡、能譜等多種實驗手段對焊接結合層的微觀組織結構、高溫下nb - 1zr與不銹鋼合金元素的互擴散行為，形成的互擴散層的成分、金相組織和擴散層中的析出相的相組成和相結構等，都進行了較為詳細的分析，並且對在不同工藝、不同焊接參數下焊接的nb - 1zr合金和不銹鋼的焊縫做了強度實驗研究。
  9. The variable polarity power supply circuit uses two stages full - bridge inverter, the former inverter is regarded as a constant - current source with fast dynamic response, and supplys energy for the second one, and the latter one is to produce variable polarity current excellently, and low - frequency pulse current by variable polarity power supply is used to reduce input energy and control the shape of weld bead while welding. a series of high - frequency pulse current is superposed on direct - current - electrode - negative ( dcen ) current through the high - frequency pulse power supply, which is used to compress the arc and improve process of crystallization

    其中變極性電源採用二次全橋逆變結構，一次逆變提供快速的響應速率並給二次逆變提供能量，二次逆變提供良好的變極性性能，使輸出能量最優化，並用其低頻電流特性減小電弧線能量，控制焊縫成形;高頻脈沖電源提供的高頻電流疊加在反極性電流dcen上，利用電流的高頻特性壓縮電弧，改善焊縫金屬結晶過程。
  10. Self adjust function of electric arc, easy arc igniton, less spatters, perfect weld appearance

    電弧自調節能力強，引弧成功率高，焊接飛濺小，熔敷率高，焊縫成形美觀。
  11. It is proved by the intensity experiment of welding line that the welds of these two materials using explosive welding and vacuum electron beam self - material brazing are tolerable, nevertheless the welding technique could be improved basing on the study of microstructure of the joint layer

    通過強度實驗的研究，兩種工藝形成的焊縫強度都是可以滿足目前的應用要求的，但是，對電子束自釬焊可根據顯微研究的結果做進一步的工藝參數的改進。
  12. This paper takes advantage of numeric simulation technology to investigate the weld - line movement and formability of twb with the same property and different thickness, analyzes the weld - line movement in three different drawing ways with the same drawing depth, and shows the normal rule of weld - line movement in different drawing ways, and the relationship between the weld - line movement and formability of twb of different thickness

    摘要本文利用數值模擬技術對相同材質差厚拼焊板的沖壓成形性和焊縫移動進行研究，分析了相同拉延深度、不同拉延方式下焊縫移動情況，揭示了不同拉延方式下焊縫移動的一般規律和焊縫移動量與差厚拼焊板成形性之間的關系。
  13. Minimal the tendency of microcracks can be obtained by improving the shape of weld pool and enhancing the welding energy input

    通過改善焊縫成形和提高焊接線能量有助於減小兩類熱影響區微裂紋傾向。
  14. The arc physical characteristic of mixed gases ( ar + he + co2 ) and its effects on weld shaping were discussed

    摘要採用鎢極氬弧焊對不同比例氬氦二氧化碳混合氣體的電弧物理特性及其焊縫成形進行了實驗。
  15. Weld appearances and mechanical properties of friction stir welded joint of al alloy and mild steel

    鋁合金與鋼的攪拌摩擦焊焊縫成形及接頭性能
  16. Effect of single constituent fluoride flux on argon arc welding seam forming of ti alloy

    單組分氟化物焊劑對鈦合金氬弧焊焊縫成形的影響
  17. Form factor of weld

    焊縫成形系數
  18. Study on shaping mechanism of weld for tig - mig double - sided symmetrical arc welding

    雙面對稱焊焊縫成形機理研究
  19. Study on the physical characteristic of argon - helium arc and its effects on the weld shaping

    二氧化碳混合氣體電弧行為及其對焊縫成形的影響
  20. A system for the weld power source was established with digital signal processor ( dsp ), and variable polarity power supply output, high - frequency pulse current, protection and process control were fulfilled with the software all, and modulate low frequency pulse current by means of amplitude modulation, through which it could also control the shape of weld seam like the low frequency pulse current welding

    在模擬控制器基礎上引入了dsp數字控制技術，用軟體編程實現了電源的變極性輸出、高頻脈沖電流的疊加及保護和電源的時序控制，使之能夠在大尺度上調制出低頻脈沖，控制焊縫成形。
分享友人
分享到 Line

分享到臉書