焊縫高 的英文怎麼說

中文拼音 [hànfénggāo]
焊縫高 英文
final height
  • 焊 : 動詞（用熔化的金屬修補金屬器物或使金屬工件連接起來） weld; solder
  • 縫 : 縫名詞1. （接合處） seam 2. （縫隙） crack; crevice; fissure; slit
  • 高 : Ⅰ形容詞1 （從下向上距離大; 離地面遠） tall; high 2 （在一般標準或平均程度之上; 等級在上的） above...
  1. The results show that the slag series has strong capabilities of deoxidization, denitrification and dehydrogenation and is able to protect welds and obtain high quality welds

    試驗結果表明，其渣系具有很強的脫氧、脫氮和脫氫能力，對焊道能起到很好的保護作用，可獲得高質量的焊縫。
  2. The welding technology of francis turbine runners is optimized from the view of subsection welding and local heating by numerical simulation. the result shows that welding residual tensile stress appears in the weld and its area nearby, and peak stress appears in the dangerous area of blades after practising quondam welding technology ; welding residual tensile peak stress in the dangerous area of blades can be decreased by welding both ends earlier and then welding middle section later during subsection welding, and decreasing effect on welding residual stress of the subsection welding is related to the weld length of blade outlets and welding direction of each subsection ; decreasing effect on residual stress of the local heating is direct proportional to heating time, heating temperature, heating area, and inversely proportional to cooling area, and welding residual tensile peak stress in the dangerous area is decreasing trend earlier, and then increasing trend later with heated location increased

    本文利用數值模擬手段對轉輪的焊接工藝從分段焊和局部加熱兩個方面進行了優化，結果表明:採用普通工藝焊接時，葉片焊后殘余拉應力出現在焊縫及其附近區域，並且在葉片出水邊的熔合線附近（危險區域）出現了峰值;在採用優化的分段焊時，先焊兩端后焊中間的方法可以降低葉片危險區域的焊接殘余拉應力峰值，降低效果與葉片出水邊焊段長度、焊縫各段的焊接方向有關;局部加熱法降低轉輪危險區域殘余應力的效果主要與加熱時間、加熱溫度以及加熱面積成正比，與冷卻面積成反比，並且危險區域的殘余應力隨加熱區域的增大呈先降低后升高的趨勢。
  3. The kind of welding equipment is suitable forwelding the qarts in appplications of heat exchanger in - out water pipe port of electical heater and hot pipe fittings simple operation low lost and good seam foring are the advan tages. it is an essential and special equipment in the profression of tube - making electrical and solar water heaters

    該系列焊接設備適用於太陽能熱水器端蓋及水箱內受到影響上的進出水管、熱管接頭、電加熱器接頭及搪瓷水箱進出水管的自動化焊接，焊縫盛開有美觀、效率高、成本上升低，是制桶業、太陽能熱水器、電熱水器等行業必不可少的專用設備。
  4. Inductotherm group china - thermatool shanghai is a sister company of thermatool group, has more than 50 years experience in designing and manufacturing hf welders, seam annealers, tube / pipe inline bring / dull annealers ( stainless steel, carbon steel, etc. ), tube / pipe form mill and relevant spare parts. as the leading supplier of welders and seam annealers in the world, thermatool has provided wide range of welders and seam annealers to pipe and tube industries

    應達工業（上海）有限公司色瑪圖爾分公司和美國色瑪圖爾公司是姊妹公司，同屬美國應達工業集團，具有50多年專業生產製造高、中頻焊機，焊縫退火設備，管材（碳鋼、不銹鋼）在線光亮/暗退火裝置，焊管成型機組及其附件的豐富經驗，為世界上眾多的行業提供了相應的專業化設備，同時也是世界上最大的高頻焊機和焊縫熱處理設備的製造商。
  5. The machine is used for pvc door and window transom “ v ” or “ + ” - shaped welding cleaning work. it features advanced technology, reliable function and easy operation

    本機用於pvc塑料門窗中梃v形焊縫的清理。它具有性能可靠、操作方便、高效率等優點，尤其適用於批量生產。
  6. All the size of fillet welds k are the thickness of the wall except those marked

    未注焊縫焊角高度k均為焊件中薄壁的厚度。
  7. Abstract : with the aids of computer ' s hardware, executive mechanism of weld arc length automatic controller of all - position pipe welder and additional software, an automatic system for arc striking has been developed, in which touch - starting method using tiny current is introduced. utilizing this method, the ablation ratio of tungsten electrode and tungsten inclusion ratio of welded seam is far smaller than normal touch - starting method. and the successful ratio of arc striking is high

    文摘:用全位置自動焊管機弧長自動控制系統的計算機硬體和執行機構，僅增加部分程序，設計了採用小電流接觸引弧法的自動引弧系統，鎢極燒損和焊縫夾鎢遠小於普通的接觸引弧方式，引弧成功率很高。
  8. As plasma, welding arc has well electric character. exterior magnetic field can affect shape and movement of welding arc. and the welding bead and drops transfer can also be changed to improve the welding process and advanced the productivity

    電弧作為一種等離子體，具有優良的導電性，用外部磁場可以改變電弧的形態和運動特性，影響焊縫熔池和熔滴過渡形式，大大改善焊接工藝，提高焊接生產效率。
  9. The explosive welding specimen were also annealed in vacuum at various elevated temperature from 1000 to 1300. optic microscope, sem, tem and eds ( electron diffraction scattering ) techniques are applied to observe the microstructure and the element profiles of the welding interface and the interdiffused layer, reveal the interdiffused performance of alloy elements at elevated temperature, and analyze the structure and composition of the precipitated phases. moreover, the tensile strength of welding line with the two different techniques and various welding parameters were carried out

    採用金相、掃描電鏡、透射電鏡、能譜等多種實驗手段對焊接結合層的微觀組織結構、高溫下nb - 1zr與不銹鋼合金元素的互擴散行為，形成的互擴散層的成分、金相組織和擴散層中的析出相的相組成和相結構等，都進行了較為詳細的分析，並且對在不同工藝、不同焊接參數下焊接的nb - 1zr合金和不銹鋼的焊縫做了強度實驗研究。
  10. The results show that the absolute humidity of the welding environment has great influence on the hydrogen diffusion, and that the greater the absolute humidity, the higher the content of hydrogen diffused in deposited metal

    結果表明，焊接環境的絕對濕度對超低氫焊條熔敷金屬中擴散氫含量有較大影響，絕對濕度越大，焊縫金屬中擴散氫含量越高。
  11. The variable polarity power supply circuit uses two stages full - bridge inverter, the former inverter is regarded as a constant - current source with fast dynamic response, and supplys energy for the second one, and the latter one is to produce variable polarity current excellently, and low - frequency pulse current by variable polarity power supply is used to reduce input energy and control the shape of weld bead while welding. a series of high - frequency pulse current is superposed on direct - current - electrode - negative ( dcen ) current through the high - frequency pulse power supply, which is used to compress the arc and improve process of crystallization

    其中變極性電源採用二次全橋逆變結構，一次逆變提供快速的響應速率並給二次逆變提供能量，二次逆變提供良好的變極性性能，使輸出能量最優化，並用其低頻電流特性減小電弧線能量，控制焊縫成形;高頻脈沖電源提供的高頻電流疊加在反極性電流dcen上，利用電流的高頻特性壓縮電弧，改善焊縫金屬結晶過程。
  12. Determination of shear strength of welded joints of reinforcement mats or cages for prefabricated components made of autoclaved aerated concrete or lightweight aggregate concrete with open structure

    高壓充氣混凝土或敞開結構輕型聚集混凝土預製件用加筋氈或框架的焊縫剪切強度測定
  13. A fuzzy control system of stepping motor for seam tracking is presented in this paper, the proposed system can realize the self - modify ing of the parameters and improve the characteristics of dynamic and static state of stepping driving system according to the error of seam tracking. the accuracy of seam tracking is enhanced obvi ously

    介紹一種用於焊縫跟蹤的步進電機模糊控制系統，該系統可根據跟蹤偏差進行參數自調整，改善了步進驅動系統的動靜態特性，提高了焊縫跟蹤精度。
  14. The results of the experiments show that the ti3al - tcll dual alloys, by vacuum - electron - beam weld, hot die forging and 680c / 12h, ac, heat treatments, have satisfied synthesis properties of intensity, plasticity, hardness. and also it is the feasiblie way. this will establish the supporting technology for the manufacture of the compress disk in the areoengine

    實驗結果表明，經真空電子束焊接ti _ 3al ? tc11雙合金經過熱模鍛造和680 12h ， ac或815 1h + 700 8h ， ac熱處理后，焊接區組織過渡均勻，可以使得焊縫處強度在室溫拉伸時高於ti _ 3al ，而在600拉伸時高於tc11合金，獲得強度、塑性、硬度均令人滿意的綜合性能，且是一條可行的工藝路線。
  15. The commonly used methods of connections, especially the high - strength bolted connection and welding with bolting mixed connections are discussed in more detail. the analysis for the problems, such as partial penetrated butt weld and welding deformation is also discussed in the paper

    對工程中採用較多連接如高強度螺栓連接、栓-焊混合連接等作了較深入分析；對工程中容易出現問題連接如不焊透的對接焊縫計算方法及可能出現的焊接變形及處理等問題也作了較深入探討。
  16. The number of inspected air holes often exceed the limitation of standard if the ready task of cleaning up before welding has not been done completely. automation of welding will be a necessary trend in order to improve the work condition and enhance the quality of welding

    鑒于焊接工人的勞動環境改善以及焊接質量的提高，焊接自動化是一個發展的必然趨勢，目前國內外雖然對自動tig焊研究較多，但是針對中厚壁鋁合金縱焊縫的雙面tig自動立焊仍是空白。
  17. Compared with conventional weld methods, electron beam welding possesses such advantages as high power density, strong penetrability, precise, high speed, good control ability, good protection effect and high quality

    與常規的焊接方式相比，電子束焊接具有功率密度高、穿透能力強、精確、快速、可控性好、保護效果好、焊縫質量高等優點。
  18. Self adjust function of electric arc, easy arc igniton, less spatters, perfect weld appearance

    電弧自調節能力強，引弧成功率高，焊接飛濺小，熔敷率高，焊縫成形美觀。
  19. When the welding current is added, the fusion quality of welding stick will increase, so the weld reinforcement also will increase

    焊接電流增加時，焊絲的熔化量也增加，因此焊縫的余高也隨之增加。
  20. Both single and double fillet welds shall be as follows unless otherwise shown on the drawing

    除非圖上另外標明，所有單、雙面貼角焊縫高度如下。
分享友人
分享到 Line

分享到臉書