無應力件 的英文怎麼說

中文拼音 [wúyīnglìjiàn]
無應力件 英文
unstrained member
  • 無 : 無Ⅰ動詞（沒有） not have; there is not; be without Ⅱ名詞1 （沒有） nothing; nil 2 （姓氏） a surn...
  • 應 : 應動詞1 （回答） answer; respond to; echo 2 （滿足要求） comply with; grant 3 （順應; 適應） suit...
  • 力 : Ⅰ名1 （力量; 能力） power; strength; ability; capacity 2 [物理學] （改變物體運動狀態的作用） forc...
  • 件 : Ⅰ量詞（用於個體事物） piece; article; item Ⅱ名詞1. （指可以一一計算的事物） 2. （文件） letter; correspondence; paper; document
  1. Application of caving mining technology with bottom under condition of flat dipping mid - thick body and unstable rock caused the most of trench and bottom drift, located in abutment, to be destroyed and low recovery in south area, xishimen iron mine

    摘要在緩傾斜中厚礦體底板巖性不穩固的條件下，採用有底柱崩落法，由於電耙道大多處于空區邊部應力集中的部位，致使塹溝及底部結構巷道破壞嚴重而使回收率極低，採用無底柱崩落卸壓則可有效解決上述難題。
  2. The study indicate that the surface form has no effect on kl, but has obvious effect on kll, and will affect the breaking angle and mode ; in finite plate, the boundary condition has effect on the sif and the k is bigger than in infinite plate ; the effect of the distance and the angle between cracks are all have obvious effects on the multiple crack interaction, and the interactions between cracks also have obvious effects on the sif, which can be neglect only when the distance is bigger enough

    研究表明：裂面狀態對k _的大小沒有影響，而對k _的影響卻很大，相同應力條件下，裂面狀態會影響裂紋的開裂角和開裂方式；有限板的邊界對應力強度因子有一定的影響，其k比無限板中的k略大；裂紋間的距離、夾角等因素對裂紋間的干涉效應均有較大影響，裂紋間的干涉效應對應力強度因子的影響非常顯著，只有當裂紋間的距離充分大時，干涉效應才可忽略。
  3. The stress distributions under load or unload as well as under fatigue tension with or without split - sleeve were studied, so as to reveal the advantage of coldworking with split - sleeve

    研究了帶襯套擠壓件在加載、御載及疲勞拉伸載荷狀態下的應力分佈，並和無襯套擠壓時的狀態進行比較，從機理上揭示了帶襯套擠壓在改善試件抗疲勞性能方面的優勢所在。
  4. The paper fristly compared the fertile soil with the incinerated sterile soil on the number of micro - algae, soil ph value, soil organic matter soil available phosphorus and soil nitrogen. and then, the author put fertile soil, which included micro - algae, proportionally into sterile samples and cultivated them respectively under illumination condition ( micro - algae can live and reproduce ) and dark condition ( micro - algae will die in some time ). the above indices were measured in 0, 30, 60 and 90days respectively, the analyse of the interrelation between the change of micro - algae ' s number and the changes of soil ph value, soil organic matter, soil available phosphorus and soil nitrogen indicated : ( l ) soil micro - algae which were native to fertile soil conld adapt to the changed circumstance and light acted as a decisive role to the distribution of soil micro - algae. under dark condition, the micro - algae ' s number declined gradually and went to zero in the end, while under illumination condition, on the 90th day, the micro - algae ' s number of per gramme was 6 - 7 times more than that of the beginning

    本文首先對肥沃土壤與經高溫焚燒后的貧瘠土壤中的微藻數量、土壤ph值、有機質含量、有效磷含量和全氮量進行比較研究，然後將包含微藻的綠化苗圃地肥土按不同比例接種進入貧瘠土樣中，分別在光照條件和黑暗條件下進行培養，在0天、 30天、 60天和90天分別檢測以上指標，比較有光條件和無光條件下，即有藻條件和無藻條件下貧瘠土樣所發生的變化，並分別對微藻數量的變化與土壤ph值、有機質含量、有效磷含量和全氮量的變化之間做相關性分析，以評估肥沃土壤中的微藻接種進入貧瘠土壤后的生長情況以及對貧瘠土壤的改良作用。研究結果表明： （ 1 ）土壤微藻對環境有較強的適應能力，且光照對其分佈起了決定性的作用。
  5. Cqf product is mainly made of reinforced pp and all flow - through pump parts adopt injection mould with resistance to most organic and inorganic acid, alkali and salty solutions, applicable for being exposed outdoor with fine anticorrosive performance of stress corrosion cracking

    Cqf型產品以增強聚丙烯為主要材料，泵的過流零部件均為注塑成型，能耐大多數的有機和無機酸、堿和鹽類溶液，也適于在室外大氣中暴露，對應力腐蝕破裂的抗蝕性良好。
  6. Reliability of fibre optic interconnecting devices and passive optical components - life stress modeling

    纖維光學互連裝置和無源光學元件的可靠性.壽命應力模型
  7. In this paper, the high - temperature low - cycle fatigue life and fatigue crack propagation life tests are carried on the cylindrical axial symmetry specimens having precrack or non - precrack with different types of notches of 16mnr steel in common use in the petrochemical industry contacting coke drum equipment, the stress / strain and the range of stress / strain of dangerous points are received through stress analysis of the specimens using finite element program under multi - axial stress state. at last, the equations of evaluating the high - temperature low - cycle fatigue life and the fatigue crack propagation life are found through using the least - square regression method

    本文採用無預裂紋和帶預裂紋環狀缺口圓柱形試樣，進行了石化焦炭塔設備常用材料16mnr多維應力狀態下不同缺口形式的高溫低周疲勞總壽命試驗及裂紋擴展壽命試驗，並利用有限元程序對試樣缺口周圍及裂紋尖端附近進行了軸對稱多維應力狀態下的應力、應變場分析，來評價材料不同條件下的高溫低周疲勞總壽命和裂紋擴展壽命，最後利用最小二乘回歸方法，得到了該材料高溫低周疲勞總壽命和裂紋擴展壽命評價方程。
  8. Reliability of fibre optic interconnecting devices and passive optical components - part 7 : life stress modeling

    纖維光學互連器件和無源光學元件的可靠性.第7部分:壽命應力模型
  9. Iec 62005 - 7 - reliability of fibre optic interconnecting devices and passive components - part 7 : life stress modeling

    Iec 62005 - 7 .纖維光學互聯器件和無源元件的可靠性.第7部分:守命應力制模
  10. The experimental component design of unbonded prestressed concrete slab under fire

    無粘結預應力混凝土板火災試驗構件設計
  11. Recently, train is running faster and faster, and considering the stability and security, seamless welded rails ( swr ) are used as the train orbits gradually. the temperature of the rails will vary with weather. so that the rails may release the energy due to the metal characteristic of expanding or contracting with temperature, there is some badly distortion in the swr, worsly occurring accidents on expanding orbits. the portrait thermal stress ( pts ) of the swr should be monitored in some parts regularly, as to avoid such accident

    近年來，隨著火車的提速造成的穩定和安全問題，軌道逐步轉為採用無縫焊接鋼軌，隨著鋼軌溫度的變化，無縫鋼軌可能會因為熱脹或冷縮的金屬特性並且在扣件阻力小而且路基較差的路段釋放能量，可能會發生鋼軌嚴重變形，更甚者會發生脹軌跑道等嚴重鐵道事故，為了避免發生如此事故，有必要定期對鋼軌的溫度應力進行檢測。
  12. In this paper, based on the analysis of the rlem of theory foundation, computing method, preference, applicability, etc, we anatomized the rlem of three self - deficiencies and six scarcities. moreover, we adopted the parallel ways of contrasting the rlem with the fem and applied it to analyzing the impact of slide block of elasticity and plasticity, slip surface of coefficient and slip bed of elasticity, plasticity upon the stability of slope and in the plain linearity slope, the plain refracted line slope and the plain arc slope. in addition, we discussed the warp of between the lem of ( sarma, janbu, order, bishop, morgenstera - price, etc ) and the fem of result and the distributing of positive stress and shear stress on the slip surface

    本文從剖析剛體極限平衡法的理論基礎、計算方法、參數選取、適用條件等方面入手，剖析了剛體極限平衡方法的3點自身缺陷和6點不足，並在此基礎上採用了剛體極限平衡法（平面滑動破壞法、 sarma法、傳遞系數法、普遍條分法、 janbu法、 bishop法、 morgenstern - price法）與大型有限元法對比研究的方法，分析研究了平面直線型滑坡、平面折線型滑坡、平面圓弧型滑坡在漸進破壞中邊坡的滑體彈塑性參數、滑麵塑性參數） 、滑床的彈塑性、以及極限平衡法無法考慮開挖應力釋放等因素對邊坡穩定性的影響與滑動面上的正應力、剪應力分佈規律、安全系數的解答的差異。
  13. The detailed discussions were focused on the prestress construction, especially on the protection measures against erosion

    對無粘結預應力施工進行了詳細的論述，並著重論述了預應力構件的防腐保護措施。
  14. Not a timely manner to facilitate the dissolution of auto parts fault detection, vulnerability directly on the surface of metal parts nondestructive testing of the fatigue crack, stress corrosion, crack, crack, etc. folded through " sound ", " light " emergency instructions crack site to the maintenance staff promptly eliminate hidden dangers and guarantee the exercise of automotive safety

    及時方便不解體檢測汽車部件故障，直接對易損金屬部件表面進行無損檢測，對出現的疲勞裂紋，應力腐蝕、裂紋、折疊裂紋等、通過「聲」 、 「光」報警指示裂紋的部位，以使維修人員及時排除隱患，保證汽車安全行使。
  15. Fibre optic interconnecting devices and passive components - basic test and measurement procedures - tests - screen testing of ceramic alignment split sleeve by stress application - section 24 screen testing of ceramic alignment split sleeve by stress application

    纖維光學互連器件和無源元件.基本試驗和測量程序.試驗.用施加應力進行陶瓷準直套管篩選
  16. This article describes a way of special ultrasonic system which monitors thermal stress in seamless welded rails. this monitoring system is a non destructive testing system, which adopts avr mcu and high - precise time chip processing as the core of it, and adopts the critically refracted longitudinal wave as the object of measuring. my studying focuses on the theory of the monitoring system, which will be listed in this arctile : according to the snell theory, the theory of motivating of critically refracted longitudinal wave is described in details, and the finite element software is used to emulate the propagating course. the formulas of calculating the pts of swr are taken from the acoustoelasticity theory, and the calculating the parameters is introduced. according to assemble materials, three kinds of ways of monitoring the pts of swr using critically refracted longitudinal wave are described, which are measuring the sound - time in changeless distance, ultrasonic critical - angle refractomery and frequency spectrum, the first way of ways is used in this experiment system. the factors, which effect the monitoring system, are assaid in some degree based

    本文的研究工作重點在無縫焊接鋼軌溫度應力測量系統的理論模塊，包括根據snell原理，研究極限折射縱波的激發機理，並使用有限元軟體ansys進行模擬;根據聲彈性理論以及公式推導出計算無縫焊接鋼軌中的溫度應力的公式，並對其中參數的求解方法進行介紹;根據收集的資料，介紹了三種使用極限折射縱波測量無縫焊接鋼軌溫度應力的方法，即固定距離測量聲時法、臨界角折射法和頻譜分析法，本實驗系統使用的是第一種;根據實驗經驗以及相關資料，分析了影響極限折射縱波測量溫度應力的幾個因素，並提出了相應的解決方法;根據實驗系統的需要，獨立設計並加工出相關配套的實驗設備，包括實驗鋼塊、有機玻璃楔塊、固定件、載荷外框裝置等。
  17. With the aid of the obtained fundamental solutions and the continuity conditions of stress and displacement on material interface, complex potentials solutions for an bi - material infinite plate with an elliptical inclusion under pulling stress are given

    根據界面上應力和位移的連續條件，得到了單向拉伸狀態下，含有橢圓夾雜的無限大雙材料組合板的復勢解。
  18. Depending on how the ground surface is denuded, the feature of the current crustal stress field and rock stress environment can be calculated analyzing the result in this paper : by analyzing the recovering feature of the elastic deformation of the rockmass in unload - stage under various pressures, it has been found there is close relationship between the recovering degree of the elastic deformation of the rockmass and the unloading degree of the pressure the direction of the major principal stress in the crustal stress field is not consistent with the direction of the crushing stress regional tectonics borne during the last tectonic movement. the evolving degree of the regional geomorphology evidently affects the current crustal stress field, which changes from the self - weight stress field to the horizontal stress field, with the changing of the eroding degree of the regional geomorphology ranging from valley area to hilly country to flat country. in valley area, where there is two stress belts, the bankslope s tress belt and the self - weight stress belt within the mountain. the direction of the major principal stress is nearly parallel to the ground surface and inclines towards the valley in the bankslope stress belt. it is nearly vertical in the self - weight stress belt

    通過本文的研究成果，根據區域性地貌的演化特徵，我們可以大致地對現今地應力場進行判斷：在分級卸荷條件下，巖體中彈性變形的恢復具有明顯的規律性，這種規律對于研究地應力場的演變是有幫助的；地應力場中最大主應力方向與區域構造形跡在最近的構造運動中所受區域性擠壓應力的方向無明顯的對應性；區域性地貌形態的演化程度對現今地應力場的特徵具明顯的影響，隨著區域性地貌侵蝕程度由峽谷區、丘陵區、平原區的變化，現今地應力場特徵由自重應力場、水平應力場為主含少量自重應力場特徵向水平應力場的規律變化；在峽谷區，山體中具有兩個應力帶：自重應力帶和卸荷應力帶，最大主應力方向在卸荷應力帶中近平行於坡面並傾向于河谷、在自重應力帶中近於直立；根據原始地面遭剝蝕的程度，可以大致地估算最大主應力和中間主應力的量值和方向；在丘陵區和平原區，最大主應力的方向近於水平，並與附近區域性侵蝕盆地和河流的展布方向基本平行，根據原始地面遭剝蝕的程度，可以大致估算其最大主應力的量值；根據區域性地貌形態的特徵來分析工程區的現今地應力場特徵，並進而大致了解巖石的應力環境，這種分析方法得出的結論與許多實際的地應力測試成果基本一致，對于大型水電工程地下廠房和壓力隧洞的設計是有所幫助的。
  19. A new method, which is based on the force equilibrium condition and the geometrical compatibility condition of cable, according to the constant unstressed length of cable, is presented in this paper to determinate the geometric of suspension bridge free cable. numerical examples with humen suspension bridge are given to demonstrate the effectiveness and the validity of the proposed method

    根據索的力的平衡條件及變形相容條件，由纜索無應力長度不變的原則來建立纜索狀態方程，提出了懸索橋主纜空纜狀態線形分析的一種新方法.以虎門懸索橋為例對該方法的正確性和適用性進行驗證，可供橋梁工程技術人員設計參考
  20. Abstract : a new method, which is based on the force equilibrium condition and the geometrical compatibility condition of cable, according to the constant unstressed length of cable, is presented in this paper to determinate the geometric of suspension bridge free cable. numerical examples with humen suspension bridge are given to demonstrate the effectiveness and the validity of the proposed method

    文摘:根據索的力的平衡條件及變形相容條件，由纜索無應力長度不變的原則來建立纜索狀態方程，提出了懸索橋主纜空纜狀態線形分析的一種新方法.以虎門懸索橋為例對該方法的正確性和適用性進行驗證，可供橋梁工程技術人員設計參考
分享友人
分享到 Line

分享到臉書