無機填料 的英文怎麼說

中文拼音 [wújītiánliào]
無機填料 英文
inorganic filler
  • 無 : 無Ⅰ動詞（沒有） not have; there is not; be without Ⅱ名詞1 （沒有） nothing; nil 2 （姓氏） a surn...
  • 機 : machineengine
  • 填 : 動詞1. （墊平或塞滿） fill; stuff 2. （補足; 充滿） replenish; supplement; complement 3. （填寫） fill in; write
  • 料 : 名詞1 （材料; 原料） material; stuff 2 （喂牲口用的穀物） feed; fodder 3 （料器） glassware 4 （...
  • 無機 : [化學] inorganic無機氮肥 inorganic nitrogenous fertilizer; 無機肥料 inorganic fertilizer; 無機化...
  1. Ptfe has many excellent properties such as : bonzer self - lubrication ^ low fricatiom chemistry stabilization and thermal stabilization, but its wear resistance is very low to improve the wear resistance of ptfe a lot of researches have been down by means of adding fillers to it, there are still less report on nano - inorganic filler filled ptfe composites to change properties. in this paper, experimental study was made to question above problem

    Ptfe具有優異的自潤滑、低摩擦、化學穩定性和熱穩定性，但耐磨性較差，因而人們在利用不同種類的填料對ptfe進行填充改性，提高耐磨性方面作了大量研究工作，但在使用納米無機填料填充改性ptfe方面研究很少，因此本課題主要探討這一方面的問題。
  2. The acidtreated packing causes release of co2 from inorganic carbonates.

    酸化處理過的填料會使co2從無機碳中釋放出來。
  3. Application of the ultra - fine comminution technology in filler made from inorganic mineral

    超細粉體技術在無機礦物填料中應用的研究現狀
  4. Aiming at improving the lipophilic property of the conductive fillers, surface modification of conductive tio2 powders and conductive mica powders has been researched by 5 kinds of coupling agents

    摘要為了提高無機導電填料的表面親油性，選擇5種偶聯劑分別對導電二氧化鈦粉體及導電雲母粉體進行了表面改性，活化指數評定了改性效果。
  5. Our factory succeeds in developing the new - type lightweight solid aluminium buckle - panel through practice for many years. this kind of metal buckle - panel includes double - sided panel body with one side of the buckle - panel as the bayonet connector, another side as the bayonet, lightweight filling material inside the panel body, fireproofing material filled inside the fireproofing metal buckle panel, possessing better strength of panel body, resulted in sound insulation, heat insulating, more ideal surface luster of the heat insulation panel body and no mechanical veins, beautiful appearance and difficult deformation

    本廠經過多年實踐成功研製新型實心金屬扣板，此款金屬扣板包括雙面的板體，板體的一側為卡接頭，另一側為卡口，板體中間帶有輕質填充物，防火金屬扣板中間另注防火材料，具有更好的板體強度，隔音隔熱保溫板體面光澤更加理想無機械紋，外形美觀難變形。
  6. The results indicated that the dimension, shape and purity of base material could meet the functional demand of solid lubricant ; the thermal decomposition temperature of ptfe resin exceeds 400 c, but organic and inorganic packing filler added in ptfe made the water absorption rate of composite material increased, melting temperature and decomposition temperature decreased, in the meanwhile oxidative decomposition reaction was accompanied ; polar groups such as c = o, c - o - c and so on in the carbon fiber surface is advantageous to increase compatibility with other components and interlayer shearing strength ; uniform design experimental method could help to find the relationship between formula and frictional property by relatively small tests. the developing trend of each formula ' s friction coefficient could be showed by fitting curve ; the friction coefficient with no copper powder or graphite in formula was relatively big. this fact showed that copper powder and graphite should be used cooperatively ; it was found that when the ratio of copper powder to graphite by weight is 15 : 60, 30 : 30 - 40 and 60 : 15 - 30 respectively, the friction coefficient was relatively small. the degree of crystallinity of pure ptfe reached maximum by air cooling and the abrasion loss also reached maximum among three ones ; at the same time, the abrasion loss of solid lubricant sample was also the biggest among three ones ; when solid lubricant matched with 45 # steel axle or gcrl5 steel axle, lubricant transfer film could be formed on metal surface, thus direct contact between the surface of metal friction pair rings was reduced. their working life was elongated extremely ; there was mainly much graphite, a little ptff, moo3, feso4, cus and so on in lubricant transfer film

    試驗結果表明：所選原料的尺寸、形狀及純度可滿足固體潤滑劑的性能要求；聚四氟乙烯樹脂熱分解溫度超過400 ，但在ptfe中加入無機填料會使復合材料吸水率提高，熔融溫度及分解溫度降低，且伴有氧化分解反應；碳纖維表面含有c = o及c - o - c等極性基團，有利於提高其與其它組分的相容性，提高層間剪切強度；均勻設計試驗方法能夠用較少的試驗次數找出配方與摩擦性能間的關系，擬合曲線基本能表示各配方的摩擦系數發展趨勢；配方中不加銅粉或不加石墨，其摩擦系數均較高，說明銅粉和石墨應該配合使用；當銅粉15份、石墨60份時，銅粉30份、石墨30 - 40份時，銅粉60 、石墨15 - 30份時，摩擦系數均具有較低值；純聚四氟乙烯樹脂在空氣冷卻時結晶度最大，磨損量也是三者中最大的；同時，固體潤滑劑試樣在空氣冷卻時的磨損量也是三者中最大的：不論是固體潤滑劑與45 #鋼軸配副或是固體潤滑劑鑲嵌入銅套后與gcr15鋼軸配副，在金屬表面均可形成潤滑轉移膜，從而減少金屬摩擦副表面間的直接接觸，大大延長其使用壽命;轉移膜中主要含有較多的石墨、少量聚四氟乙烯、 moo 。
  7. The superfine quartz powder is a sort of neutral inorganic fillers which is widely applied in plastic, rubber, rosin, dope, electron and other high and new - technology industries, the purity and granularity is required strictly in high and new - technology industries

    超細石英粉是一種優質的中性無機填料，廣泛應用於塑料、橡膠、樹脂、塗料、電子及高科技產品等行業，其中高科技行業對超細石英粉的純度和粒度組成都有相當嚴格的要求。
  8. Thus, the system could be kept at a lower super - saturation state under the condition of higher concentration of ca2 + to obtain aragonite whisker. the surface of aragonite must be modified to overcome the shortcomings leading to poor dispersion and combination with polymer materials

    為了解決作為無機填料由於表面親水疏油而在聚合物材料內部分散性差、與高聚物本體結合力差等的缺點，必須對文石相碳酸鈣晶須進行表面改性。
  9. In this paper, using partly neutralized acrylic as monomer and kaolin as abio - filler, poly ( sodium acrylate ) / kaolin composite superabsorbent was prepared and its properties were studied

    摘要以部分中和的丙烯酸為單體，以高嶺土為無機填充料，通過反相懸浮聚合法合成出聚丙烯酸鈉高嶺土復合高吸水性樹脂。
  10. Test method for qualitative examination of mineral filler and mineral coating of paper

    紙和紙板中無機填料和無機塗料的定性分析試驗方法
  11. Paper and board. qualitative analysis of mineral filler and mineral coating. chemical method

    紙和紙板中無機填料和無機塗料的定性分析化學法
  12. Paper and board. qualitative analysis of mineral filler and mineral coating. sem edax method

    紙和紙板中無機填料和無機塗料的定性分析電子顯微鏡x射線能譜法
  13. New product and application of foreign mineral fillers

    國外無機填料新產品及其應用
  14. In the field of high polymer material, kaolinite is the inorganic filler with more excellent performance than montmorillonite

    在高分子材料領域，高嶺土是性能較蒙脫土更加優異的無機填料。
  15. The pure uhmwpe and a series of uhmwpe - base composites reinforced by cu powder or cuo powder were prepared by means of heat moulding. their tribological behaviors were studied

    以模壓法研製了uhmwpe材料、無機填料銅粉改性uhmwpe復合材料以及氧化銅改性uhmwpe復合材料，並對其摩擦學行為進行了研究。
  16. The designs of composite material using inorganic filling compounds to reinforce ultra high molecular weight polyethylene ( uhmwpe ) and an improvement on thermal conductivity of polymer working as tribological material were selected as the major research subject in this thesis

    本論文選擇無機填料改性超高分子量聚乙烯（ uhmwpe ）復合材料的材料設計和聚合物作為摩擦學材料時導熱性能、抗壓強度及抗蠕變性能的改進研究作為主要研究方向。
  17. Sintering or friction all brought about chemical change in the surface of solid lubricant and the change of valen ce state of mo, s, fe and so on ; the micro - hardness of pure ptfe was minimum and the surface - hardness of solid lubricant was increased with the increase of additional packing filler in formula ; the compressive strength of pure ptfe was minimum and its compressive strength could be increased notably by adding organic and inorganic filler. but not more additional amount, more notable increase of compre

    、 feso4 、 cus等物質;燒結及摩擦均使固體潤滑劑表面發生化學變化，使mo 、 s 、 fe等元素的價態發生變化;純ptfe的顯微硬度最低，固體潤滑劑的表面硬度基本是隨著填料加入量的增加而增加的;純ptfe的抗壓強度最低，在ptfe樹脂中加入無機填料均可明顯提高其抗壓強度，但並不是加入量越多，抗壓強度提高越明顯。
  18. The method blending with rigid inorganic filler can improve tensile strength, while lowering impact strength of blends. so, the critic prohlem is how to increase impact strength and tensile strength simultaneously. recently hybrids of pp / clay but melting interca1ation method have been studied, and the results show that higher impact strength is obtained, while tensiie strength lost less

    改善pp韌性的常用方法是與橡膠或彈性體共混復合，但在提高材料韌性的同時，拉伸強度損失嚴重；若用無機填料來改性pp ，材料的拉伸強度得到提高，但韌性下降較大，故提高即的韌性和拉伸強度似乎成了一對矛盾。
  19. The adsorption theory of micropore inorganic materials was studied to direct the preparation of tsous by organic / inorganic nano composite materials. the microstructure of tsous was established based on the theory that the micropore is filled during the process of micropore materials adsorption

    研究了微孔無機材料的吸附理論，提出微孔材料的吸附過程相當于工質材料對微孔的充填，其孔體積均為吸附空間。
  20. Because of their excellent characteristics, superabsorbents are widely used in health, agriculture and horticulture applications. based on the influencing factors, such as type of structural layer, interlayer charge, interlayer distance, cation exchange capability, surface area and ratio of swelling, kaolinite, sercite and bentonite are choosed as the mineral fillers to synthesize the superabsorbent composite

    本文從粘土的結構層型、層電荷、層間距、陽離子交換容量、比表面積和膨脹率等各方面綜合比較研究粘土礦物的性質，選擇了高嶺土、膨潤土和絹雲母這三種粘土礦物作為無機填料，制備粘土?有機聚合物超吸水性復合材料。
分享友人
分享到 Line

分享到臉書