熔入型模 的英文怎麼說
中文拼音 [róngrùxíngmó]
熔入型模
英文
consumable former-
The physics model was established to deduce the relationship of different classifying gear speeds and melting point on the base of the broken theory and the broken process of pvc. it explained that the melting point of nanocrystalline pvc was low. therefore the effect of nanocrystal was proved in theory
最後通過引入破碎理論針對pvc的破碎過程,建立物理模型推導出分級輪旋轉速度與晶體熔點的關系,解釋納米晶pvc熔點低的原因,從而從理論上探討了pvc的納米晶效應。Using the modified analytic embedded - atom method ( maeam ), the molecular dynamics ( md ) simulation was performed to study the premelting and melting behavior of ( 001 ) plane of niobium and tungsten
摘要採用改進分析型嵌入原子方法( maeam ) ,對鈮、鎢晶體的( 001 )面預熔和熔化過程進行分子動力學模擬。The screw is forced forward, injecting the plastic melt through the nozzle, on through the sprue and runners, and into the cavities of the closed mold
螺桿向前推進,將熔融物料通過噴嘴、主流道、分流道注入閉合的模具型腔中。Abstract : a laser damage facilities, which has mm size spot and operates in tem00 mode , were achieved. in order to know the reasons of laser damage, the laser energy density was controlled near the damage threshold of the oxide thin films. according to the examined near - threshold damage morphology, the damage mechanisms of the optical coatings can be divided into two types. one was caused by melting of the coating materials, another by exploding, induced with the inner stress of the film. the plasma generated was an important reason to expand the damage area
文摘:採用毫米量級大光斑的近單模的激光器,控制入射薄膜表面的激光能量,獲得了幾種常見單層膜和增透膜的損傷形貌,實驗結果表明,薄膜的損傷可區分為熔化型和應力型兩種,薄膜表面等離子體對損傷斑點的擴大有重要作用。The hot runner series makes the plastics in the hot runner from the nozzle of a plastics injector to the inlet of cavity must be always kept at such a molten state by means of heating that you just pick out the product, there is no need for you to take the condensing stuffs from the injection system as the mould cavity is operated
說明:熱流道系列用加熱的方法使從注塑機噴嘴到型腔入口為止這一段流道中的塑料一直保持熔融狀態,在開模時只需取出產品,而不必取澆注系統凝料。This is accomplished by melting plastic resin ; injecting it into the mold and then having the part separate from the mold on cooling
這由把可塑的樹脂熔化來完成,將之注入模型然後當冷卻時從模型中將這個部分分離出來。A fuzzy controller with two input variables and one output variable is considered to be suitable to control weld pool width. the input variables of the fuzzy controller are the variation of the welding pool width and its rate, and the output variable is the welding currert
本文對熔寬模糊控制器的結構以及模糊控制變量的選擇進行了討論,在此模糊控制系統中採用雙輸入單輸出的模糊控制器模型,即採用熔寬的變化及其變化率作為模糊控制器的兩輸入量,採用焊接電流作為模糊控制器的輸出量。分享友人