熔化析出 的英文怎麼說

中文拼音 [rónghuàxīchū]
熔化析出 英文
liquate
  • 熔 : 動詞（熔化） melt; fuse; smelt
  • 析 : Ⅰ動詞1. （分開; 散開） divide; separate 2. （分析） analyse; dissect; resolve Ⅱ名詞（姓氏） a surname
  • 熔化 : melt; smelt; meltdown; fusion; fusation; diatexis; eliquation; run; melting; smelting
  1. And apatite. by these analyses and comparison with general granite both in china and the world and with the granite in other au or cu belt in china, the characteristics of the granite in this area are concluded as follows. it belongs to magnetite - i or syntectic granite and has crust - mantle mixed characteristics ; it was formed mainly by crystallization differentiation of melting magma and multiphase varied intrusion ; the degree of differentiation evolvement is not high ; the granite and its enclaves p. re congenetic ; the range of temperature is about 500 - 700, the range of pressure is about 2. 50 gpa - 4. 35 gpa, and the range of oxygen fugacity ( lg fo2 ) is - 15. 53 - - 14. 00 ; most granite bodies formed before the collision of plates, and few formed after the collision of plates

    通過對測試數據的分析與綜合研究，並同中國和世界一般花崗巖類以及中國主要金、銅成礦巖體的花崗巖類進行對比，得出本區花崗巖類巖石具有以下特徵：屬磁鐵礦-型或同熔型花崗巖，其巖漿物質具殼幔混源特徵：主要由熔融態巖漿經結晶分異作用，通過多期變速上侵而形成；其分異演化程度較低；寄主巖基和包體具有同源性；巖石的形成溫度范圍約為500 - 700 ，壓力大約為2 . 50gpa - 4 . 35gpa ，氧逸度值1gfo _ 2為- 15 . 53 ? 14 . 00 ；該巖帶主要形成於板塊碰撞前消減的活動板塊邊緣期，為燕山至喜馬拉雅早期的大陸邊緣火山弧環境的產物。
  2. Based on the petrological, petrochemical and geochemical analyses about these rocks, it is concluded in this paper that the xenoliths were originated from the upper mantle, and comprised of both primitive pyrolite and the infusible solid residual of the upper pyrolite while the basaltic magma was melted out of it, which were brought up to the earth ' s surface via o1carnc eruption

    根據其巖石學、巖石化學及地球化學特徵分析，包體來源於上地幔，其成因既有原始地幔巖，亦有上地幔巖經部分熔融出玄武巖漿后的難熔固相殘留物，被火山噴發攜帶至地表。
  3. The imported transparent glaze fired at lower temperature was analysed semi - quantitatively by adopting emission spectroscope. the stripping of lead and cadmium from this transparent glaze fired at lower temperature in ceramic product was determined by atomic absorption spectroscope. the effect of chemical composition on the stripping of lead and cadmium was analysed. upon the author s opinion, the overproof lead stripping from the imported transparent glaze fired at lower temperature can only be settled by adopting lead - free glaze instead of adopting low - lead prescription. the author succeeded in developing an excellent lead - free transparent glaze fired at the lower temperature of 1000 1050. the success is based on an inquiry into the feasibility of using such new agents of fusion as li2o and sro in replacement of pbo ; and on a study of the effects of the contents of sio2 ， al2o3 ， b2o3and other metallic oxides on such performances of glaze as coefficient of linear expansion, fusion temperature and transparency. it is also based on an analysis of coefficient of linear expansion of blank and glaze on an analysis of coefficient of linear expansion of blank and glaze on their correlation ; and on a study of technology for preparing glaze

    採用發射光譜儀對進口低溫透明釉進行半定量分析，並用原子吸收光譜儀測定其陶瓷製品的鉛、鎘的溶出量，分析化學成分對鉛、鎘溶出量的影響.結果表明，進口低溫透明釉採用低鉛配方不能解決鉛溶出量的超標問題，只有採用無鉛釉才能解決.探討用氧化鋰和氧化鍶等新型熔劑完全代替氧化鉛的工藝，研究釉料中氧化硅、氧化鋁、氧化硼和各種金屬氧化物的含量，對釉的線膨脹系數、熔融溫度和透明度等性能的影響.分析坯料、釉料的線膨脹系數及其相互關系和釉料制備的工藝，研製出優質的1000 1050低溫無鉛透明釉
  4. By analyzing the microstructure of as - cast alloys with different surplus of samarium added, the optimum surplus of samarium is decided. by comparing the microstructure of the alloys annealed for different time, the ideal and economical annealing time is confirmed. the microstructure and phase composition of alloys during the whole preparation of sm2fe17nx are analyzed using the scanning electron micrograph with energy - dispersive x - ray analysis and x - ray diffraction patterns

    本論文首先就熔煉工藝參數對鑄態組織微結構的影響進行了探討，並制定出一套較為合適的熔煉工藝；通過對不同釤加入量的鑄態組織微觀結構的觀察分析，確定了原料配置過程中釤的最佳補償量；通過對採用不同退火時間的合金組織進行比較，確定了理想、經濟的退火時間；同時還利用掃描電子顯微圖像和x射線衍射圖譜，比較了整個制備過程中，試樣微結構和相組成的變化情況。
  5. The paper discusses dynamical conditions of the supercritical ore - forming fluid system based on study of regional geological background and analyses of physiochemical conditions of ore - forming process and puts forth the ore - forming mechanism : upper mantle uplift - mingling of meteoric water and magmatic hydrothermal fluid separated from acidic magma under tensile or transitional tensile environment - water / rock reaction - transportation - chemical coupling ore precipitation

    在分析超臨界成礦流體系統形成的區域地質背景和研究成礦物理化學條件的基礎上，探討了超臨界成礦流體系統形成的動力學條件，提出該系統的成礦機理：與燕山晚期酸性火山侵入巖漿有關的金銅礦床是在上地慢隆起、張性或向張性過渡背景下形成的，酸性巖漿經熔體流體分離作用形成的巖漿熱液與大氣降水混合，經水巖作用等復雜的輸運和化學反應耦合過程的動力學產物。
  6. The crystallization and melting behavior of mellocene - catalized branched and linear polyethylenes of low molecular weight was studied. it was found that the crystalline lattice of branched polyethylene is larger than that of linear polyethylene because of the existence of branched chains. the melting behavior of branched polyethylene is similar to that of linear polyethylene since the branched chains can not enter the lattice. however, the crystalline behavior of low molecular weight branched polyethylene is the same as that of high molecular weight linear polyethylene, but different with that of low molecular weigh linear polyethylene. kinetics theory analysis evidenced that the transition temperature of growth regime of the branched polyethylene is about 20 lower than that of linear polyethylene with the same molecular weight. it may be attributed to the existence of short branched chains

    研究了金屬茂催化的低分子量支化聚乙烯和線性聚乙烯的結晶及熔融行為，發現支化聚乙烯的結構與線性聚乙烯相同為正交結構，但晶格略有膨脹.支鏈的存在對熔融行為影響不大，兩種聚乙烯的熔點均隨結晶溫度的升高而非線性增加，表現出低分子量樣品的共同特徵.但支鏈的存在對結晶行為卻有很大的影響，主要是由於支鏈的存在降低了晶體的結晶速率從而影響結晶過程，使得低分子量的支化聚乙烯的結晶行為與高分子量線性聚乙烯的結晶行為相似而與低分子量的線性聚乙烯不同.動力學分析表明，低分子量的支化聚乙烯的結晶生長方式的轉變溫度比同等分子量的線性聚乙烯降低了約20
  7. The technological capabilities of electronic solders were presented through analysis the action of solders in the soldering process, which includes temperature of melting or solidifying, anti - oxidation capability, wetability and overflow capability

    摘要通過分析焊料在釬焊過程中的行為，提出了電子焊料的工藝性能主要包括熔化固化溫度、抗氧化性、潤濕性和漫流性。
  8. Find the law of the influence from the injection pressure to the filling time and the cavity pressure and make certain of the best filling time, injection time and injection pressure. though the analysis of the flowing velocity and pressure spread of the key position element in the injection parts in different gate position, we forecast the injection parts quality and the possibility injection flaw and its position, optimize the gate position. in this paper, though the research of analogue of the runner system of metal - powder injection molding and the process of injection molding, we get the law of how the injection parameter influence the injection process

    在相同的注射條件下，通過分析喂料在不同直徑和長度流道中的流動規律，得到了喂料在流道中的速度場、壓力場和溫度場，找到了流道長徑比的合理取值范圍，並得出通過改變流道設計可實現對現有設備資源充分利用的結論；給出了不同注射壓力下，型腔壓力與充模時間關系曲線和喂料熔體平均充填速度與充模時間關系的曲線，得到了注射壓力對充填時間和型腔壓力的影響規律，確定了最佳的充模時間、注射時間和注射壓力；通過分析採用不同位置澆口注射時注射件關鍵位置單元的流動速度和壓力分佈，預測了注射件的成形質量，或可能產生的注射缺陷及位置，優化了澆口設置。
  9. Through the statistic analysis on the change of the melt gear pump working condition pre - and post - pet plant capacity increasing and concatenate direct spinning process, the reasons for the unsteady running were studied, the modification measures such as lubricating the oil groove with sliding bearing, mechanical sealing of the gear pump, decreasing the gear pump outlet pressure, changing the automatic speed increasing to hand speed increasing were put forward

    摘要通過對聚酯裝置增容和後接直紡長絲前後熔體齒輪泵工況變化的統計分析，研究其運行不穩定的原因，提出改造措施，包括滑動軸承潤滑油槽，齒輪泵的機械密封，降低齒輪泵出口壓力，改自動提速為手動提速等等。
  10. We calculate the stress fracture limit, critical index limit and melting limit in a high power double clad fiber laser. the results show that the average output power decreases when the temperature is too high. to maintain the pumping efficiency and the output power, some cooling methods should be used when the output power reaches a certain level

    給出了熱效應對雙包層光纖激光器影響的裂解極限、臨界折射率極限和熔化極限與光纖結構參數和泵浦功率的表達式，理論分析和數值模擬結果表明對于高功率的雙包層光纖激光器溫度很高時激光增益下降，在一定的功率水平上需要進行外界的冷卻，以保證泵浦激光的效率和高功率的激光輸出。
  11. Finally, the roughness of sidewalls is reduced greatly by rising the temperature, which results in more effective discharging of air bulbs in the melted surface

    再一方面，通過升高材料溫度的方法，有助於激光加工過程中側壁熔化層內氣泡的有效析出，可以大幅降低側壁粗糙度。
  12. Aiming at reducing the roughness of the sidewalls in the manufacturing of the pmma liquid pool by co _ 2 lasers, in the hypothesis that the intensity of the laser has a guassian distribution, the temperature distribution in slab material with limited thickness is studied according to traditional thermal conductive formulas, and the condensing progress of the melted surface of sidewalls is researched. it is concluded from the discussion of temperature distribution that the air bulbs is the major reason for the roughness of the sidewalls

    為降低co _ 2激光加工pmma材料儲液池側壁粗糙度，本文根據傳統的熱傳導方程，假定激光強度為高斯分佈，對有限厚板狀材料的溫度場進行分析;並考察側壁表面熔化層凝固過程的特徵;結果表明，側壁粗糙度形成的主要原因在於側壁表面熔化層凝固前氣泡未及時析出。
  13. Through the analysis of the evolution of the microstructure, the honey comb at the grain boundary and the pool in the grain, furthermore according to the phase change thermodynamic and kinetics, the conclusions of the globalization mechanism and the reheating parameters were drawn as follows. 1

    通過對半固態再結晶和半固態熔化過程中的組織轉變、晶界蜂巢及晶內液池現象的分析，結合相變熱力學和動力學原理，提出sima法制備鎂合金半固態球狀化組織的形成機制及工藝參數。
  14. The experiment result showed that, in the infiltration melting the evaporation speed of si is more rapid than mo. the melting which enrich the mo reacted with the sic body and there existed mo5si3c. the content of mosi2 can be controled by adjusting the contend of c in the perform ; the content of c is more high the pore volume in composite is more high

    研究發現，由於熔滲體中si的揮發速度快造成材料物相組成變化，熔滲體與sic坯體反應析出mo _ 5si _ 3c 、 mo _ 5si _ 3相阻塞坯體毛細管，使燒結體中產生氣孔。
  15. The physical and mathematical models are founded. numerical simulation of marangoni convection in the liquid bridge and gas channel was performed by employing the primitive variable method and using galerkin finite element method, which is applied for discretization of non - dimensional governing equations and boundary conditions. the relationship between the suppressing status of mc in the liquid bridge and the inlet gas velocity or the channel width is obtained, and the suppressing status of some kinds of marangoni numbers ( ma ) or size ratios of liquid bridge a is analyzed

    採用原始變量法，用galerkin有限單元法對無量綱控制方程及邊界條件進行離散后，數值模擬了微重力條件下半浮區硅熔體及氣體流道內的marangoni對流，得出了無量綱氣流沖刷速度及流道寬度變化和熔體內熱毛細對流抑製程度的關系，進而分析了不同的無量綱參數ma數和不同熔體幾何尺寸比a下熱毛細對流抑制情況。
  16. The coupled turbulent flow field and temperature field are simulated by finite element method ; the influence of casting speed on the turbulent flow field and temperature field in the melting bath and the interaction between those two field are analyzed ; the variation tendency of the heat flux intensity between the melting bath and casting roll and law of variation with changes of casting speed in the process of solidification are given ; a comparison between the simulation results and experimental results demonstrates their good agreement ; and the mechanism of the heat flux variation is identified by analysis on the temporature gradient and development of solidification within the melting bath and its influence on the variation of the heat flux intensity

    採用有限元法模擬了雙輥鑄軋不銹鋼過程的流熱耦合問題;分析了鑄軋速度對熔池內流場、溫度場的影響以及流場與溫度場之間的相互影響;給出了凝固過程中熔池與鑄軋輥之間的熱流密度變化趨勢及隨鑄軋速度的變化規律，並把此模擬的結果與試驗的結果相比較，吻合較好;通過熔池內溫度場及溫度梯度分析了熔池內凝固的發展及其對熱流密度變化的影響。
  17. The thermodynamic conditions of decomposition of the foaming agent tih2, homogeneous and heterogeneous nucleation in high - temperature solid and liquid, growth and movement were achieved to demonstrate the trend of pore evolvement in this paper. moreover, according to the characteristics of in - situ gas foaming, the equations of the height change of foaming samples with heating time were primarily established to study the behavior of foams and to guild the experiment processes

    另外，論文通過大量的熱力學分析，得出了發泡過程中發泡劑分解以及氣孔在固液態時的均勻形核和非均勻形核、氣孔的生長和運動等熱力學條件，揭示了氣孔演化的趨勢；論文還根據內生氣源發泡的特點，初步建立了高溫熔體中氣體發泡高度隨時間變化的方程，為進一步深入的研究發泡機理奠定了一定的基礎。
分享友人
分享到 Line

分享到臉書