熔化面積 的英文怎麼說
中文拼音 [rónghuàmiànjī]
熔化面積
英文
melting area-
The qitaihe coal resources isadvantageous, the coal field total area 8, 000 square kilometers, haveverified the geological reserve 1. 7 billion tons, the prospectivereserves 4. 2 billion tons, the coal plant completely, has the cokingcoal, 1 / 3 coking coal, the gas coal, the anthracite and so on 10varieties, by coking coal primarily ; excellent in quality, has theespecially low phosphorus, especially low characteristic and so onsulfur, high heat value, high ash melting point, high silicon content, most is suitable for the coal chemical industry product thedevelopment, is national one of three big protections mining rare coalfields, is the heilongjiang province most important anthraciteproduction base, also is the national important coking coal and thenortheast area biggest high quality coke production base
七臺河煤炭資源得天獨厚，煤田總面積8000平方公里，已探明地質儲量17億噸，遠景儲量42億噸，煤種齊全，有主焦煤、 1 / 3焦煤、氣煤、無煙煤等10個品種，以主焦煤為主；品質優良，具有特低磷、特低硫、高發熱值、高灰熔點、高硅含量等特點，最適于煤化工產品的開發，是全國三大保護性開采稀有煤田之一，是黑龍江省最重要的無煙煤生產基地，也是國家重要的主焦煤和東北地區最大的優質焦炭生產基地。The welding technology of francis turbine runners is optimized from the view of subsection welding and local heating by numerical simulation. the result shows that welding residual tensile stress appears in the weld and its area nearby, and peak stress appears in the dangerous area of blades after practising quondam welding technology ; welding residual tensile peak stress in the dangerous area of blades can be decreased by welding both ends earlier and then welding middle section later during subsection welding, and decreasing effect on welding residual stress of the subsection welding is related to the weld length of blade outlets and welding direction of each subsection ; decreasing effect on residual stress of the local heating is direct proportional to heating time, heating temperature, heating area, and inversely proportional to cooling area, and welding residual tensile peak stress in the dangerous area is decreasing trend earlier, and then increasing trend later with heated location increased
本文利用數值模擬手段對轉輪的焊接工藝從分段焊和局部加熱兩個方面進行了優化，結果表明:採用普通工藝焊接時，葉片焊后殘余拉應力出現在焊縫及其附近區域，並且在葉片出水邊的熔合線附近（危險區域）出現了峰值;在採用優化的分段焊時，先焊兩端后焊中間的方法可以降低葉片危險區域的焊接殘余拉應力峰值，降低效果與葉片出水邊焊段長度、焊縫各段的焊接方向有關;局部加熱法降低轉輪危險區域殘余應力的效果主要與加熱時間、加熱溫度以及加熱面積成正比，與冷卻面積成反比，並且危險區域的殘余應力隨加熱區域的增大呈先降低后升高的趨勢。On the other hand, under the force of mechanical, the carbon and cao & sio2 superfine powder are obtained ; the specific surface area of these particles is increased. the tem photos indicated that, the carbon particles are composites on the surface of the melting superfine particles uniformly
另一方面，在機械力作用下，碳黑及cao sio _ 2的熔融顆粒被超細粉碎，比表面積增大，同時tem照片顯示，中超碳黑均勻地復合於超細熔融顆粒表面，並有逐步嵌入的趨勢，提高了碳的有效利用率，降低了保護渣的熔化速度。Distributive mixing is achieved in twin screw extruders with narrow kneding block segments
而分佈混合是將熔體分割為條紋，進行均化，增大接觸面積。At the same time, based on weld pool image characters, a method for image processing is presented, in which gray - scale morphological operators is used to process weld pool images. by this method, the important geometrical parameters of weld pool are measured
同時結合實際的焊接自動化中熔池圖像的特點，詳細介紹如何利用灰度形態學，設計基於com的形態處理運算元，並且實時提取熔池的最大寬度、半長、後部面積、后拖腳等重要的幾何參數。Typical temperature is 800 - 1000 in cvd diamond process, while the high temperature limits its application in optical window and coating such as gaas, zns etc. low temperature can not only make diamond crystal nucleus finer, reduce surface roughness of diamond films and lessen light dispersion, but also eliminate thermal stress
化學氣相沉積金剛石膜過程中，襯底的典型溫度為800 1000 ，這么高的溫度限制了其作為gaas 、 zns等低熔點光學材料窗口和塗層的應用。低溫沉積金剛石膜不僅可以使晶粒細化，降低表面粗糙度，減小光的散射作用，而且可以消除熱應力。1. the splitting from the binding interface of cuw / crcu roots from the rich cr and the oxidation of the binding interface, which leads to the higher thermal resistance in binding interface than normal, and the thermal stress enhanced. the extruded cu is suggested to instead of casting cu
（ 1 ）斷裂是由於原材料鑄態的crcu中c :質點大於熔滲的孔隙而沉積在界面上，同時在有氧源存在的條件下，結合面氧化，致使結合面結合不好，界面熱阻升高， cuw與crcu部分的膨脹不同，應力集中，燃弧后斷裂。分享友人