熔結成型 的英文怎麼說

中文拼音 [róngjiēchéngxíng]
熔結成型 英文
fusion molding
  • 熔 : 動詞（熔化） melt; fuse; smelt
  • 結 : 結動詞（長出果實或種子） bear （fruit）; form （seed）
  • 成 : Ⅰ動詞1 （完成; 成功） accomplish; succeed 2 （成為; 變為） become; turn into 3 （成全） help comp...
  1. Abstract : the formation technologies, the structure and properties of tcs microporous man - made yarn - kind new polyester fibre which was spinned in tcs with some micrometallic - oxide have been studied. the results indicate that the rheological behaviour and spinnability of commixed polyester melt, and the structure and properties of the fibre, are relative to the spinning temperature, melt pressure, microporpus size for spinning, formation conditions, thermo - vascellum temperature, thermo - vascellum position and rolling speed, besides the viscosity of polyester cuts, coacervation particles, adding amount and size of micrometallic - oxide

    研究表明， tcs微孔化共混聚酯熔體在成型加工中的流變行為和可紡性，及其纖維的結構性能除了與原料切片的特性粘度、凝聚粒子和共混聚酯中超細金屬氧化物微粒的添加量、粒徑等因素的影響有關外，還與紡絲溫度、紡絲熔體壓力、噴絲板微孔尺寸、冷卻成形條件、熱管溫度、熱管安裝位置以及卷繞速度等因素的影響密切有關。
  2. And apatite. by these analyses and comparison with general granite both in china and the world and with the granite in other au or cu belt in china, the characteristics of the granite in this area are concluded as follows. it belongs to magnetite - i or syntectic granite and has crust - mantle mixed characteristics ; it was formed mainly by crystallization differentiation of melting magma and multiphase varied intrusion ; the degree of differentiation evolvement is not high ; the granite and its enclaves p. re congenetic ; the range of temperature is about 500 - 700, the range of pressure is about 2. 50 gpa - 4. 35 gpa, and the range of oxygen fugacity ( lg fo2 ) is - 15. 53 - - 14. 00 ; most granite bodies formed before the collision of plates, and few formed after the collision of plates

    通過對測試數據的分析與綜合研究，並同中國和世界一般花崗巖類以及中國主要金、銅成礦巖體的花崗巖類進行對比，得出本區花崗巖類巖石具有以下特徵：屬磁鐵礦-型或同熔型花崗巖，其巖漿物質具殼幔混源特徵：主要由熔融態巖漿經結晶分異作用，通過多期變速上侵而形成；其分異演化程度較低；寄主巖基和包體具有同源性；巖石的形成溫度范圍約為500 - 700 ，壓力大約為2 . 50gpa - 4 . 35gpa ，氧逸度值1gfo _ 2為- 15 . 53 ? 14 . 00 ；該巖帶主要形成於板塊碰撞前消減的活動板塊邊緣期，為燕山至喜馬拉雅早期的大陸邊緣火山弧環境的產物。
  3. The difference of reactive mechanisminduced the difference of their structure. v _ 2o _ 5 product prepared by melting - cooling showed more notable undefined structure. after heat - treating under300, particle size becomes smaller, and aggregate to globate grain, showesbetter electrochemical performance at low charge - discharge rate

    熔融淬冷法合成的樣品其無定型結構更明顯，前驅體經過300熱處理后，材料的粒徑變細，團聚成球狀的顆粒，球狀特徵更顯著，在低倍率下具有較好的電化學性能。
  4. The imported transparent glaze fired at lower temperature was analysed semi - quantitatively by adopting emission spectroscope. the stripping of lead and cadmium from this transparent glaze fired at lower temperature in ceramic product was determined by atomic absorption spectroscope. the effect of chemical composition on the stripping of lead and cadmium was analysed. upon the author s opinion, the overproof lead stripping from the imported transparent glaze fired at lower temperature can only be settled by adopting lead - free glaze instead of adopting low - lead prescription. the author succeeded in developing an excellent lead - free transparent glaze fired at the lower temperature of 1000 1050. the success is based on an inquiry into the feasibility of using such new agents of fusion as li2o and sro in replacement of pbo ; and on a study of the effects of the contents of sio2 ， al2o3 ， b2o3and other metallic oxides on such performances of glaze as coefficient of linear expansion, fusion temperature and transparency. it is also based on an analysis of coefficient of linear expansion of blank and glaze on an analysis of coefficient of linear expansion of blank and glaze on their correlation ; and on a study of technology for preparing glaze

    採用發射光譜儀對進口低溫透明釉進行半定量分析，並用原子吸收光譜儀測定其陶瓷製品的鉛、鎘的溶出量，分析化學成分對鉛、鎘溶出量的影響.結果表明，進口低溫透明釉採用低鉛配方不能解決鉛溶出量的超標問題，只有採用無鉛釉才能解決.探討用氧化鋰和氧化鍶等新型熔劑完全代替氧化鉛的工藝，研究釉料中氧化硅、氧化鋁、氧化硼和各種金屬氧化物的含量，對釉的線膨脹系數、熔融溫度和透明度等性能的影響.分析坯料、釉料的線膨脹系數及其相互關系和釉料制備的工藝，研製出優質的1000 1050低溫無鉛透明釉
  5. 2, upon heating to their respective melting temperature, all the compounds above went to liquid crystal phase. the typical chiral smectic c phase lined texture and finger print texture, smectic fan texture and broken fan shaped texture, nematic schlieren texture schlieren texture and ball grandle texture, paramorphosis texture can be observed

    實驗結果表明：一，化合物2 、 4 、 16 、 17和18均具有熱致液晶性；二，以上化合物加熱至各自的熔點以上都能形成液晶態，在液晶態可以觀察到新的席夫堿型液晶冠醚的合成與表徵手性近晶c相的層線織構和指紋織構。
  6. Rapid prototyping technology changed the traditional pattern of product design, which could offer product sample for the designer, reduced design cycle and quicken the schedule of new product design, and it gave the decision - makers visual feeling. ; rp technology provided kinds of molds including resin - boncled mold laminate mold, investment mold and lost foam casting mold and so on for sand casting investment casting and cavityless casting, it could also use direct shell production casting to make pattern dies metal dies die - casting dies injection dies directly, and it could even produce casting products in small scales. the applications of fdm technology in plaster precision casting and the rapid casting technology based on sls technology were introduced, the organic combination between rapid prototyping tecnnology and foundry process, which initiated a new period of rapid manufacturing metal parts, by using advanced new technology alternated traditional foundry industry to make it looked brand - new, thus, the competition of foundry industry would be improved ; rapid prototyping technology offered a rapid economical feasible technical method, common processes of using rapid prototyping technology to produce dies were discussed, in the paper it explored that. the problem of combining rapid prototyping technology with electric arc metal - spraying technology to make metal dies and technics in dies manufacturing of combining rapid prototyping technology with precision casting, rapid tooling based on rapid prototyping, integrated advanced new technology and tradition technology of rapid prototyping manufacture, each superiority were exerted, rapid prototyping technology had been an efficiency measure to rapid update products and develop new product, and to middle -

    快速成型技術改變了傳統的產品開發模式，可以為設計者提供產品樣件，縮短設計周期，加快新產品的開發進度，為決策者提供直觀性；快速成型技術迅速提供砂型鑄造、熔模鑄造、實型鑄造用的各種模樣，包括樹脂模、層壓模、熔模和消失模等，還可採用直接制殼鑄造法直接製造熔模鑄造用的壓型、金屬型、壓鑄型、注塑模，甚至直接製造小批量鑄件，介紹了熔積成型技術在石膏型精密鑄造上的應用和基於選擇性激光燒結技術的快速鑄造技術，快速成型技術與鑄造工藝的有機結合，開創了快速製造金屬零件的新階段，對用高新技術改造傳統的鑄造工業，使其面貌煥然一新，增強鑄造行業的競爭能力；快速成型技術為母模的製造提供了一條快速、經濟、可行的技術途徑，討論了利用快速成型技術製造模具的一般工藝方法，探討了將快速成型技術與金屬電弧噴鍍技術結合起來快速製造金屬模具問題，以及快速成型技術與精密鑄造技術相結合的模具製造工藝，基於快速成型製造的快速模具技術，集成了快速成型製造高新技術和傳統技術，發揮各自優勢，已成為產品快速更新換代和新產品開發及中、小批量生產的有效手段之一。
  7. Find the law of the influence from the injection pressure to the filling time and the cavity pressure and make certain of the best filling time, injection time and injection pressure. though the analysis of the flowing velocity and pressure spread of the key position element in the injection parts in different gate position, we forecast the injection parts quality and the possibility injection flaw and its position, optimize the gate position. in this paper, though the research of analogue of the runner system of metal - powder injection molding and the process of injection molding, we get the law of how the injection parameter influence the injection process

    在相同的注射條件下，通過分析喂料在不同直徑和長度流道中的流動規律，得到了喂料在流道中的速度場、壓力場和溫度場，找到了流道長徑比的合理取值范圍，並得出通過改變流道設計可實現對現有設備資源充分利用的結論；給出了不同注射壓力下，型腔壓力與充模時間關系曲線和喂料熔體平均充填速度與充模時間關系的曲線，得到了注射壓力對充填時間和型腔壓力的影響規律，確定了最佳的充模時間、注射時間和注射壓力；通過分析採用不同位置澆口注射時注射件關鍵位置單元的流動速度和壓力分佈，預測了注射件的成形質量，或可能產生的注射缺陷及位置，優化了澆口設置。
  8. Through the research of crosslinking of matrix resin, heating treatment of composite and mixing of different polymer, we draw some conclusions : 1 、 percolation theory can explain the phenomenon of the jump of resistance when the content of cb reach a critical volume ; 2 、 based on ohm conduct theory, abounded to the percolation the wbibull statistical theory and other theory, an adapted theory was obtained to explain the jump of resistance and the other phenomenon ; 3 、 the ntc phenomenon was eliminated by crosslinking the matrix of conductive composite, at the same time the stability of composite was improved

    通過對基體樹脂的交聯、復合材料的熱處理、聚合物共混物的研究得出了如下的結論： 1 、滲濾理論能夠很好的解釋導電粒子含量達到某一值時電導率劇增的問題； 2 、在歐姆導電模型的基礎上，綜合應用了weibull統計理論模型，結合原來的體積膨脹等理論，成功的解釋了ptc復合材料在基體材料熔點附近的跳變問題、 ntc現象以及熱循環穩定性等問題； 3 、有機ptc導電復合材料經硅烷交聯以後能夠消除ntc現象，改善了導電復合材料的穩定性能。
  9. It has a broader absorption band at 808 nm which is emitted by laser diode ( ld ). therefore, nd : cngg is suitable for ld pumping, the ld pumped all solid - state lasers can be made by using nd : cngg. in this study, nd : cngg single crystals of 25mm in diameter and above 80mm in length were successfully grown by the automatically pulling method from the melt

    摻釹鈣鈮鎵石榴石（簡稱nd : cngg ）是一種新型激光晶體，該晶體熔點低（ 1470 ） ，具有無序結構，在通用的808nm半導體激光二極體（ ld ）發射波長區有寬吸收帶，因此很適合ld泵浦，可做成ld泵浦全固態激光器。
  10. Based on our theoretical predictions, we find optimal splicing parameters on fsm - 30s fiber splicer for low loss joints between erbium doped fiber and other single mode fibers. we also experimentally demonstrate a novel three - stage erbium - doped fiber amplifier with high gain, low noise figure, and high output power. finally, a prototype of a gain - clamped fiber amplifier is obtained with high gain ( 26 db ), low noise figure ( 5. 3 db ), high output power ( 17 dbm ), and large bandwidth ( 31 nm )

    文章研究了摻鉺光纖（ edf ）與其他光纖低損耗焊接問題，得到光纖熔接機低損耗熔接的最佳參數，這對摻鉺光纖放大器的科研生產具有一定的指導意義；研究了新型的三段級聯泵浦優配的摻鉺光纖放大器的優化光路結構，得到高增益，低噪聲，大輸出功率的摻鉺光纖放大器；最後研製成功高增益（ 26db ） ，低噪聲（ 5 . 3db ） ，大輸出功率（ 17dbm ） ，寬帶（ 31nm ）增益箝制摻鉺光纖放大器樣機。
  11. Technologies such as chemical constitution selecting, alloy melting, casting process designing and optimizing, mechanical machining and heat treatment process on pump body, impeller, front and rear board of cw. nb450 dredge pump abrasion resistance parts are concluded

    摘要總結了用於挖泥船的cw . nb450型泥泵過流耐磨部件泵殼、葉輪、前後襯板的化學成分選擇、合金熔煉、鑄造工藝設計及優化、機械加工、熱處理工藝等技術。
  12. After several typical foreign desktop systems had been studied, mem ( melted extrusion manufacturing ) process was chosen as the molding process of the first rapid prototyping desktop system in china, mem200 - d, which combined our technical advantages and design experiences. by using the mechatronic design and modularization method, the system scheme design, layout design and part / assembly design have been achieved

    作者在研究了國外多種典型的桌面化快速成形系統的工藝、特點之後，結合自身的技術優勢和設計經驗，選擇熔融擠壓製造工藝（ meltedextrusionmanufacturing ，簡稱mem ）作為國內第一臺桌面化快速成形系統mem200 - d的成形工藝，同時應用機械電子學產品設計方法，結合桌面化快速成形系統的特點，以模塊化設計思想完成了mem200 - d桌面化熔融擠壓成形系統的總體方案設計、結構布局設計和零部件設計。
  13. They have excellent corrosion, thermal shock resistance and spalling resistance. they wide applications and can be used in key locations of thermal processing equipment such as bof, eaf, lf and so on. 2 alumina - magnesia - carbon brick made from high - purity bauxite or fused alumina and fused magnesia grain or high purity magnesia by pressing, resin - bond for thermal shock resistance

    1 ，鎂碳磚是不燒的耐火材料，經過摩擦壓磚機的成型以及乾燥處理后而成，它的主要原料是電熔鎂，高純鎂砂和高純石墨，結合劑為樹脂，鎂碳磚有良好的耐侵蝕性，熱震穩定性和抗剝落性，它已經被廣泛地用在鋼廠的轉爐電爐鋼包精煉鋼包等關鍵部位。
  14. The results indicate that arc melting is a good method to produce nb - si system intermetallics due to its simpler technics, lower cost and compact products. however, powder metallurgy is found to be not suitable to produce the nb - si system intermetallics due to its coarse and loose products resulting from the poor molding property of nb and si mixed powders. optical floating zone technology, which is used to fabricate nb - si intermetallic composites for the first time, is also found to be a good way to produce nb - si system intermetallics because of its compact products and good property despite of its relatively high cost

    結果表明，電弧熔煉方法制備得到的nb - si系金屬間化合物比較緻密，且制備工藝簡單，經濟實用，是一種合適的nb - si系金屬間化合物制備方法；由於nb 、 si元素粉末的成型性很差，用粉末冶金方法（熱壓燒結和冷等靜壓）制備的nb - si系金屬間化合物表面粗糙、緻密度低，且成本較高，不宜用於制備nb - si系金屬間化合物；首次用光學懸浮單晶生長技術制備的nb - si系金屬間化合物復合材料緻密度很高，盡管成本稍高，但由於性能最佳，也是一種合適的nb - si系金屬間化合物制備方法。
  15. Based on the theory of laminated object manufacturing, the technology can directly produce three - dimension miniature structure by melting nano - phased powder with fine focus. in the process of micromachines, an important technological quota is the distinguishability. in the microscopic process of rapid fabrication, the distinguishability including the scanning distinguishability and the fabrication distinguishability

    該技術將選區激光燒結快速成型技術與納米科學技術、激光技術、計算機控制技術結合起來，應用分層製造思想，以更精細聚焦的激光熔燒微、納米粉粉末直接成形三維微結構。在微機械加工中，一個重要技術指標是解析度，在快速成型微細加工中，把解析度區分為掃描解析度以及成型解析度。
  16. The microstructure of the polycrystal remains to be optimized to achieve good performance. to reduce the high cost and high - energy expedition of melting method, a solvothermal process followed by a sintering procedure of compacted pellets produced by using cold isostatic pressure method were mentioned to prepare polycrystalline samples of the ternary ( snte ) x ( bi2te3 ) y compounds

    為彌補熔煉法高成本，高能耗等諸多缺陷，本文還採用溶劑熱法，成功合成了bi _ 2te _ 3和三元（ snte ） _ x （ bi _ 2te _ 3 ） _ y化合物，並採用冷等靜壓成型，結合常壓燒結的方法制備塊體樣品。
  17. This kind of products are formed in the isopressing process and have the properties of isotropy, uniform structure, high electric conductivity, superior resistant to thermal ? shock and oxidation. it is free of pollution and infiltration for smelting metal

    該類產品採用等靜壓成型工藝，具有各向同性、結構均勻、導電性和抗熱沖擊性好、耐氧化、對熔融金屬具有不污染、不滲透等特點。
  18. In the paper, the current developments of rapid prototyping at home and abroad, the molding methods of rapid prototyping, their characteristics and the condition of applications were introduced, indicated that sterolithography apparatus ( sla ) selective laser sintering ( sls ), laminated object manufacturing ( lom ) and fused deposition modeling ( fdm ) were the several main prototyping methods of rapid prototyping at present, and their prototyping principle were briefly discussed

    本文首先介紹了快速成型技術的國內外發展現狀、快速成型技術的成型方式、成型特點和應用狀況，指出立體光固化（ sla ） 、選擇性激光燒結（ sls ） 、分層實體製造（ lom ） 、熔積成型（ fdm ）是目前使用的幾種主要成型方式，並對它們的成型原理進行了簡要介紹。
  19. The content of this dissertation is about the modification of coatings by laser cladding nano - material on plasma - spraying coatings. introducing rapid prototyping into nano material processing, experimental researches on the selective sintering of nano material are carried out systematically, the main work accomplished and conclusions gotten in this dissertation are presented as follows : 1 under the aiding of plasma spraying, reasonable coating material systems are designed to fabricate alumina, nicral / a12o3, nicral / a12o3 + 13 % wt. tio2, nicral / wc - co coating

    本文主要是在等離子噴塗的基礎上，利用激光熔覆納米陶瓷材料對等離子塗層進行改性處理，從而制備納米復合塗層；同時將激光快速成型應用於納米材料加工中，主要完成如下內容： （ 1 ）設計合理的等離子塗層結構，制備了al _ 2o _ 3 ， nicral al _ 2o _ 3 ， nicral al _ 2o _ 3 13 wttio _ 2 ， nicral wc - co四種塗層。
  20. In this paper, a series of experiments are carried out with dlms for nickel - based metal powder materials, and the effect of process parameters in sample quality was investigated and analyzed. the main works are as following : ( 1 ) the effect mechanism of laser in metal powder and the nucleation mechanism are analyzed. ( 2 ) the process parameters that affect the quality of sintering parts are investigated and the way how they affect is clear

    本文基於直接激光金屬燒結成形技術，通過對鎳基高溫合金直接激光燒結成形的研究，從工藝角度研究某型號鎳基高溫合金的激光直接燒結成形性能以及工藝參數對燒結製件性能的影響，所完成的工作主要有: （ 1 ）分析材料與激光相互作用的機理及熔池的動態快速凝固過程。
分享友人
分享到 Line

分享到臉書