熱動力計算 的英文怎麼說

中文拼音 [rèdònglìjìsuàn]
熱動力計算 英文
thermodynamic calculation
  • 力 : Ⅰ名1 （力量; 能力） power; strength; ability; capacity 2 [物理學] （改變物體運動狀態的作用） forc...
  • 計 : Ⅰ動詞1 （計算） count; compute; calculate; number 2 （設想; 打算） plan; plot Ⅱ名詞1 （測量或計算...
  • 算 : Ⅰ動詞1 （計算數目） calculate; reckon; compute; figure 2 （計算進去） include; count 3 （謀劃;計...
  • 計算 : 1 （求得未知數） count; compute; calculate; reckon; enumerate 2 （考慮; 籌劃） consideration; pla...
  1. Using the opened thermosiphon of 38x3 as experimental element and water as working fluid, the characteristics of dynamic low load boiling, stable severe boiling heat transfer coefficient and critical heat flux are gotten for the opened thermosiphon at the pressure of 0. 02 - 0. 1mpa and 0. 1 - 0. 8mpa respectively, which makes up the drawback that the opened thermisiphon has not yet accurate boiling heat transfer relationship formulas. by means of experimental results, an opened thermisiphon waste heat recovery boiler is designed for the high temperature gases that the positi e electrode copper refining furnace exhaust, which overcomes effectively the drawback of short life, little capacity and unable to inspect that the closed steel - water thermosion has

    本文以工程上常用的38 3的開口封底為實驗元件，以水為工質，對開啟式熱管內的動態低負荷沸騰、穩態旺盛沸騰及臨界沸騰特性進行系統的可視化實驗研究，實驗壓力為0 . 02 0 . 8mpa ，實驗得出了38 3的開口封底管在工作壓力為0 . 02 0 . 8mpa和0 . 1 0 . 8mpa下的管內沸騰傳熱系數及臨界熱負荷計算關聯式，彌補了開口封底管? ?這一新型傳熱元件尚無準確的沸騰換熱關聯式的缺陷。
  2. The pilot fuel model has been given to calculate the distribution of the liquid fuel and time of fuel pre - combustion, at the same time, analyzing the important action to the combustion of the natural gas in the combustion chamber of engine, determining the best quantity of pilot fuel. the explosive combustion model has been established to compute the pressure of the cylinder during the combustion, determining the main influence factors. the emission model has been established to forecast the co, nox emission

    理論方面，提出了基於化學反應的燃燒模型?多組分氣相反應系統的化學反應動力學模型，以此進行雙燃料發動機的熱力學?化學反應動力計算；引燃油燃燒模型，計算引燃油液滴的分佈規律和滯燃期，驗證引燃油在雙燃料發動機燃燒過程中的作用，揭示不同噴油規律對雙燃料發動機的影響，確定在不同負荷下的合理引燃油量；爆震模型，揭示爆震與工質能量釋放間的關系和影響爆震的各種運轉因素，確定合理的爆震依據，減小爆震傾向。
  3. Especially, to solve the functional heated calculation, which is the core work of boiler project analysis, the dissertation contributes a sequential modular iterative algorithm by referring to the theory of process system simulation

    其中，本文基於過程系統模擬理論，對鍋爐方案分析活動中最為重要的功能性熱力計算提出了一種序貫模塊迭代的新演算法。
  4. Puts forward an improved method based on the theory in which the enthalpy difference is considered as the driving force in heat transfer under wet cooling conditions and thinks that the method can halve the testing work, require less for the experiment devices and reach higher accuracy

    認為該方法遵循了焓差是濕工況下換熱推動力的規律，試驗工作量減少一半以上，對試驗裝置的要求降低，由試驗數據整理出的公式用於表冷器熱力計算完全可以滿足空調常用范圍內的要求。
  5. Approchment to the calculation on hydrodynamics of the flag pattern surface on corner tube boiler

    角管鍋爐旗式受熱面水動力計算方法探討
  6. The calculation software, which is compiled by microsoft visual c + +, can calculate the characteristic parameters of water and steam more quickly and precisely than before. further more, it can adjust the thermal parameters automatically

    此軟體界面合理，水和蒸汽的參數計算準確，熱力計算速度快，參數自動調節功能強，能完成多方面的功能，很好的勝任了本文的研究工作。
  7. Establishing on the foundation of the project of " the monitoring state and maintenance assist support system of feed pump for 300mw unit, shiheng power plant, shandong ", this paper ' s content comprise on - line monitoring and thermodynamic calculation on small steam turbine for feed water pump, and supply the necessary data for feed water pump ' s performance analysis, trouble analysis and small steam turbine ' s performance analysis, optimization, heat stress calculation and tremble monitoring

    =本論文的內容是建立在「山東石橫電廠給水泵狀態監測與維修輔助支持系統」項目基礎上，涉及大型機組鍋爐給水泵驅動用小汽輪機進行在線監測和熱力計算，為給水泵的性能分析、故障分析以及小汽輪機的性能分析和優化、熱應力計算和震動監測提供必需的數據。
  8. A multi - block incompressible viscous flow solver has been developed that can be applied to simulation of a variety of ship maneuvering related flows and calculation of hydrodynamic forces. validation and verification of the solution procedure are carried out on several model problems with good agreement to experimental and numerical results. the present block - structured viscous flow solver is based on solving the reynolds - averaged navier - stokes ( rans ) equations with a second - order cell - centered finite volume method ( fvm ) on non - staggered grids

    本文即在這種背景下，瞄準船舶操縱水動力預報方面的國際前沿和熱點課題，通過對現代船舶粘性流計算方法的研究，自主開發了一個船舶操縱粘性流求解器，並將所開發的求解器成功地應用於一系列和船舶操縱問題相關的粘性流動與水動力計算，得到了令人滿意的結果。
  9. The mainly works had been done as follows : 1. in order to keep commonality, the modules who have similar thermodynamic process had been classed. such as evaporating module ( including furnace, drum, system of boiler recycled water ), single - phase heat exchange module ( including superheater, reheater, ecomomizer ), lubricating oil system module ( can be used for any lubricating oil system of rotation mechanical impedance ), pump and fan module, ect

    本文所作的主要工作如下: 1 、為保證模塊的通用性，對鍋爐有相似熱力環節的模塊進行分類，建立模塊庫，便於模塊調用，如蒸發區模塊（包括爐膛、汽包和爐水循環系統） ，單相換熱模塊（包括過熱器，再熱器，省煤器等） ，潤滑油系統模塊（可用於各種轉機軸承潤滑油的動態特性的計算） ，泵與風機的動態計算模塊等。
  10. Examinations of steady status and analysis of dynamic experiments have been conducted on band - tube evaporator and parallel - flow condenser using r134a refrigerant. the steady examination show that the model error was under the allowable error, the inlet mass and enthalpy disturb experiments indicate that the subsection model, be good at reflecting the change of parameters of the heat exchanger, accord with the basic principle of thermodynamics theory and the actual work status. hence, the subsection simulation model research has important benefits both on theory and engineering application

    在進行模擬試驗時，以使用r134a作製冷劑的管帶式蒸發器和平行流式冷凝器為對象，完成了穩態模擬計算、試驗和動態模擬分析，穩態計算結果和試驗數據對比表明，其誤差在允許范圍內；進口質量和焓值的擾動試驗結果表明：本文所建的區段式換熱器模擬模型，能很好的反映換熱器性能參數的動態變化，與系統熱動力學理論和冷凝器、蒸發器的實際工作過程基本一致。
  11. In the paper, in accordance with the thermal power torpedo propulsion system using hap tri - component fuel, with the i - deas software, applying the cad technology and the fem, the research of simulation on the piston - one of key parts of engine was proceeded and the paper presented the whole analysis process of the piston including thermal analysis. in the paper, the question of the boundary condition in the complicated engineering was explored and the temperature field. the stress field and the deformation of the piston were computed and analyzed under a new kind of fuel ( hap )

    本文針對三組元魚雷熱動力系統，應用i - deas軟體，利用cad技術和三維有限元方法（ fem ） ，對發動機的關鍵零件? ?活塞展開模擬研究，對活塞進行了包括熱分析在內的全過程的模擬計算，探索了復雜工程中邊界條件的處理問題，分析計算了魚雷發動機活塞在新型燃料（三組元燃料）工作下的穩態溫度場、應力場與變形情況，最後，根據分析結果對其結構提出了改進意見。
  12. Explosives for civil uses - high explosives - part 15 : calculation of thermodynamic properties ; german version en 13631 - 15 : 2005

    民用爆炸物.烈性炸藥.第15部分:熱動力特性的計算
  13. The influence of fouling on the thermodynamic performance of shell heat exchanger and its design calculation is analyzed, and the choice of estimation method of fouling heat resistance and fluid flow mode is discussed

    摘要分析了污垢對管殼式換熱器的熱動力性能及換熱器設計計算的影響，討論了污垢熱阻估算方法和流體流動方式的選擇。
  14. In this article, based on the thermal calculation and the fluid functions, the steam path for steam turbines is theoretically analyzed. many data related with the fouling and structures is researched. according to the method can not only discovers the fouling generation in time, but also proceed the great cleaning project

    本課題在研究了汽輪機通流部分結垢情況、具體清洗方案以及參閱多篇技術資料后提出利用有關流動以及熱力計算的基本方程和公式對汽輪機通流部分進行理論上的模擬分析，根據此方法不僅能對于結垢情況及早發現提出問題，而且能較好的進行清洗方案設計。
  15. Combined the real testing data, the paper developed a calculation program of water wall temperature and pressure drop for designed supercritical pressure cfb boiler with vertical water walls. the hydrodynamic calculation and safety checkout under five loads was carried out

    結合實際運行的循環流化床鍋爐的熱態測試數據，開發了垂直水冷壁壁溫及水動力計算程序，根據爐膛熱負荷分佈規律，建立了膜式水冷壁熱流密度分佈函數。
  16. Secondly, the following two subjects are discussed according to the calculation of short - circuit current : ( l ) to verify the dynamic stability condition of wires by using simulated annealing algorithm ( sa ), the paper calculates the maximum value of rectangle wires " short - circuit electrodynamic stress and gets the conditions of their having the maximum value. furthermore, some concerned data about the verifying of copper wires are given by analysing vibration spectrum of the electrodynamic stress ; ( 2 ) in order to get the heat withstand conditions of wires, the paper discusses some common calculation methods, and then tries to study the problem applying artificial neural network ( ann ) based on heat principle of metals. the model is shown to be feasible

    其次，在電路中短路電流計算的基礎上， （ 1 ）進行母線的短路動穩定校驗計算：採用模擬退火演算法（ sa演算法）計算了矩形母線短路電動力的最大值及其取極值的條件，獲得了更為一般的結果，進而通過短路電動力的頻譜分析，給出了銅質母線的有關短路校驗計算數據； （ 2 ）進行母線的短路熱穩定校驗計算：討論了熱穩定校校的幾種常用計算方法，從導體或電器的發熱機理出發，運用人工神經網路理論對母線的熱穩定問題進行計算，通過算例比較，證明該方法用於熱穩定計算是可行的。
  17. According to the theory of engineering thermodynamics and phase change, heat - transfer process of the special working fluid heat - pipe stove is analyzed. some hypotheses are postulated and with the help of equation of mass - conservation, energy - conservation, the dynamic concentrative parameter model is built, the change of each parameter is prescribed at any stage from starting to stopping. with the thermodynamic calculation of burnable process, the parameter of device, such as heat - transfer coefficient / thermal efficiency etc, are achieved under steady state ; based on theoretic calculation, observing the actual running circumstance of the heating stove in person, with some performance comparison between the new and the old, the high efficiency and reliability of heat - pipe stove is proved, the project which expend it in the oil - filed is feasible

    對充入該工質的熱管加熱爐，本文根據工程熱力學和相變傳熱學及相關知識，對其進行了傳熱分析，經過適當假設，運用質量守恆和能量守恆定律，建立了裝置動態集中參數模型，描述了加熱爐從開機到穩定運行這一動態過程各參數的變化情況，同時對燃燒過程也進行了熱力計算，最終得到了穩態工況下裝置的換熱系數、熱效率等熱力參數；在理論計算的基礎上，親赴現場觀察該爐的實際運行情況，通過與原有的加熱爐的各項性能進行對比，最終證明新爐的高效性和可靠性，為其在油田中推廣的可行性提供了依據。
  18. Thermodynamic calculation for water ramjet

    水沖壓發動機熱力計算
  19. With the pressure measurement system for the swirl chamber diesel engine, by using the methods of equivalent power and the seven point three degree average for the indicator diagram, we can correct the tdc, smooth the pressure curve and make more accurate pressure data that is a well basis for the calculation of combustion heat release rate

    摘要本文在自行開發的渦流室柴油機壓力數據測錄系統的基礎上，利用等效功法和七點三次加權移動平均法，分別對示功圖進行了上止點校正和壓力曲線光順，使壓力數據更精確，為燃燒放熱率的計算打下了良好的基礎。
  20. Based on the systematical analysis of domestic and overseas agro - vehicle diesel technology status quo and trends, this paper firstly indicates the importance of developing low emission agro - vehicle diesel, and then aimed at the goal of reducing agro - vehicle diesel emission, carries through the calculations of model 680qbkz diesel thermodynamics, dynamics and fatigue intensity checkout, as well as related developments

    本文在系統分析了國內外農用車柴油機技術現狀與發展趨勢的基礎上，首先指出開發低排放農用車柴油機的重要意義，然後以降低農用車柴油機排放污染為設計目標，進行了低排放680qbkz型農用車增壓柴油機設計中的熱力計算、動力計算、疲勞強度校核以及有關的開發工作。
分享友人
分享到 Line

分享到臉書