熱效率系數 的英文怎麼說

中文拼音 [rèxiàolǜxìshǔ]
熱效率系數 英文
coefficient of thermal efficiency
  • 效 : Ⅰ名詞（效果; 功用） effect; efficiency; result Ⅱ動詞1 （仿效） imitate; follow the example of 2 ...
  • 率 : 率名詞（比值） rate; ratio; proportion
  • 系 : 系動詞（打結; 扣） tie; fasten; do up; button up
  • 數 : 數副詞（屢次） frequently; repeatedly
  • 效率 : productiveness; efficiency; productivity; workpiece ratio
  • 系數 : [數學] coefficient; ratio; modulus; quotient; factor
  1. Recent experiments have succeeded in obtaining oscillations from the new system, with frequencies of 66hz and 23hz for the cases with helium and nitrogen as the working fluids, respectively. the traveling wave system is expected to be one of the good candidates as a driver for pulse tube refrigerator, leading to a thermoacoustically driven pulse tube refrigerator without any moving component

    還利用deltae對環路部分進行了數值模擬分析，著重討論了系統的起振臨界溫度與臨界加熱功率、效率與加熱溫度的關系、噴射泵的作用以及不同工質（氮氣和氦氣）的比較等，得出一些有益的結論。
  2. The results indicated that, the fabrication process of ultra - fine grain material is mainly determined by the stress, rotate speed and the flux of cooling water. the grain refining and the hardening effect are mostly affected by the rotate speed and the flux of cooling water. compared with commercial ly12, the invalidate strength and the prolongation rate of the ultra - fine grain material are properly improved in the measurement of compression property ; and the abrupt change of the dilatability of the ultra - fine grain material at 500c is found ; also the phenomena of which the grain size of these microstructures is stable when annealed under 300c is observed

    研究表明，採用本文提出的摩擦壓扭強變形區轉移法可以得到棒狀的超細晶材料，軸向壓力、扭轉速度和溫度是採用該方法制備超細晶材料的主控參數；試件的旋轉轉速和冷卻速度對變形區晶粒細化和硬化效果影響顯著；超細晶ly12的壓縮性能與淬火+自然時效狀態的ly12壓縮性能相比，斷裂強度和延伸率均有一定程度的增強；超細晶ly12的熱膨脹系數在550左右發生明顯的變化。
  3. Aiming at such problems in combustion system of homemade middle and miniature boiler, as a complex system with the character of dead zone, time variation, serious non - linearity, large time delay, coupling and a lot of disturbance, this paper presents a new set of optimal control resources. by using well - matched control method on system, stable automatic running is realized. having the serious divulgence coals difference a lot from each other in character, instability of chemistry, value of lowest emission of heat, home - made boiler controller is not at all ideal. instead of traditional model that controls the ratio based on proportional control or with the correct signal of the amount of oxygen, this paper, combined with intellect control theory - - fuzzy control and self - optimizing concept, propounded a kind of fuzzy self - optimizing controller to be used in air supplying system of the boiler, and expatiates on the idea of dividing the control process into two parts, dynamic and static to realize, thus meets the demand of homemade boiler economic running

    本設計針對國產中、小型電站鍋爐燃燒系統參數時變、嚴重非線性、干擾因素復雜、耦合嚴重、模型不易確定的特點，提出多變量協調控制方案，解決了系統可控性差，難以實現穩定自動運行的問題；在此基礎上，改變以往以煙氣含氧量控制送風的傳統模式，針對國產電站鍋爐設備主體及一、二次送風迴路泄露嚴重，煤種混雜、成分不穩定、燃燒發熱值低、燃燒效率不高等問題，應用智能控制理論中的模糊控制技術，結合自尋最優控制的思想，設計了一種模糊自尋優控制器，應用在電站鍋爐送風控制系統上，並闡述了動靜態兩種實現途徑，通過在線優化風煤配比，實現最佳經濟燃燒，切實保障了鍋爐的經濟運行。
  4. Based on the first and second laws of thermodynamics and energy level theory, analyses the primary energy ratio, exergy efficiency and energy level difference of the household gas driven air conditioner at different conditions, and compares them with some other commonly used modes

    摘要運用熱力學第一定律、第二定律和能級分析理論，對戶式燃氣空調各種工況下的一次能源利用系數、 （火用）效率和能級差進行分析，並與幾種常用的方式進行對比。
  5. The second chapter studies the economy of ship ' s power plants, based on the aspects of lowering fuel cost, waste heat recovery, the match of ship, machinery and propeller, increasing propulsion efficiency, increasing the economy of ship ' s power plants, etc. the third chapter discusses in detail the control measures of voyage change cost, analysizes systematically the voyage change cost based on the way of fuel cost, harbor cost, voyage venture cost. the fourth chapter studies the structures and control measures of seafarers cost, maintenance cost, spare parts and stores cost, lubricating oil cost, etc. which are relatively easy to be controlled ; based on the state maintenance decision - making, a mathematical model is put forward, the validity and its solve process are discussed. the control measures of spare parts, fuel cost and lubricating oil cost should be based on scientific budget, through the control means of application, reception, usage, store check, try to acquire the inosculation of theory

    第一章主要討論營運船舶運輸成本，對船舶運輸成本的概念、結構、性質與分攤、成本細分進行了分析，從宏觀上闡明了船舶運輸成本的生存環境和生長趨勢；第二章研究了船舶動力裝置的經濟性，在營運船舶降低油耗、廢熱利用、船機槳匹配、提高推進效率、提高船舶動力裝置經濟性的有效途徑等方面進行了闡述和論證；第三章詳細論述並論證了航次變動成本的控制措施，全面系統地分析和總結了航次變動成本，通過對燃油成本、港口使費、航次風險成本的分析與控制，提出了航次風險成本的概念並論述了若干航次風險成本的控制措施；第四章對船舶營運成本中的船員費用控制、維修保養及其費用控制、船舶備件物料管理及其費用控制等幾個主要可控性較高的成本進行了細致的分析並分別討論了相互的控制措施，提出了基於狀態維修決策的馬爾可夫數學模型並論證了模型的正確性及具體解算步驟，對于備件、燃潤物料的控制堅持以科學的預算為前提，以申領、接收、使用、盤存為控制環節，切實做到理論與實踐的密切結合；第五章，結合營運成本的預核算的案例，對船舶營運成本的預算及核算進行了有益的探討，旨在揭示成本發生的動因，並給出了成本預算、核算的編制方法。
  6. Effect on boiler thermal efficiency of surplus air coefficient

    空氣過剩系數對鍋爐熱效率的影響
  7. There are 3 parts of heat loss for gas boiler, including heat emission loss, uncompleted burning loss and fume hot loss, uncompleted burning loss decreases following the increase of excess air coefficient, while fume hot loss increases. it is obvious that there exit an optimum coefficient of excess air which make boiler own highest efficiency which is the purpose of burning control

    不完全燃燒熱損失隨過量空氣系數的增大而減小，而排煙熱損失隨過量空氣系數的增大而增大，不難看出，存在一最佳的過量空氣系數使得兩者之和最小，即使得鍋爐的熱效率最高，燃燒控制的目的即在於此。
  8. Via the analysis of heat balance computation model and the computation of online heat balance for industrial coal boiler, this dissertation researched overall input heat, efficient utilized quantity of heat, heat losing of discharge flue gas, heat losing of chemistry and mechanism incomplete combustion, heat losing of dispelling heat of boiler, heat efficiency, air superfluous coefficient, wind speed, wind quantity, computation of primary air circle cutting and whose influence on boiler combustion efficiency

    本文通過對工業煤粉鍋爐熱平衡計算模型的分析，利用在線熱平衡計算，研究了總輸入熱、有效利用熱量、排煙熱損失、化學不完全燃燒熱損失、機械不完全燃燒熱損失、鍋爐散熱熱損失、熱效率、空氣過剩系數、風速、風量及一次風切圓計算以及這些因素對鍋爐燃燒效率的影響。
  9. Introducing the thermal performance calculation method called efficient factor method with the medium of the exchange coefficient on the base of the key factors which influencing the heat and humidity ' s exchange, the characters ordinary mathematics equations stem from the analysis the double spray chamber ' s thermal performance calculation identically utilizing efficient factor method, further the equations working as the core of the theory calculation and the utilization of the spray chamber ' s structure and the definition of the experimental equations, further introducing the double spray chamber ' s thermal performance calculation equations

    雙噴系統熱工計算同樣採用效率系數法，進而在理論部分引出雙噴系統熱工計算方程式，這實質上就得到了本課題的核心部分? ?組合方程組，無論是理論計算還是噴水室結構類型的採用以及試驗公式的確定均以此為核心，從而最終從理論計算、試驗測定及節能性三方面論證了雙噴水室熱回收方案的可行性。
  10. Abstract : the in servie tubular heaters built early in refineries and chemical plans have low thermal load and low heat efficiency, therefore measures for technical reform are offered, including ( 1 ) enlarging the surface area of convection tubes to increase the thermal load of rhe convection section ; ( 2 ) increasign the heat interchanging area of radiant tubes ; ( 3 ) changing the height of the chimney ; ( 4 ) using new burner with forced air supply to increase calorific capacityu ; ( 5 ) adding air preheater between the convection section and chimney to enhence the temperature of the air entering the furnace ; ( 6 ) adopting high temperature radiant coating to improve the effect of radiant heat interchanging

    文摘:針對早期建造的煉油廠和化工廠在役管式加熱爐熱負荷和熱效率低的狀況，提出了若干技術改造措施包括，增大對流管表面積以增大對流段的熱負荷；增加輻射管的換熱面積；修正煙囪高度；換用新型燃燒器，變自然通風為強制供風，以增大燃燒器的發熱量，減小過剩空氣系數，節省燃料2 % 3 % ；在對流段和煙囪之間增設空氣預熱器以提高空氣入爐溫度；採用高溫輻射塗料增強輻射換熱效果，從而增加熱源對爐壁的輻射傳熱量和爐管的傳熱量等。
  11. The in servie tubular heaters built early in refineries and chemical plans have low thermal load and low heat efficiency, therefore measures for technical reform are offered, including ( 1 ) enlarging the surface area of convection tubes to increase the thermal load of rhe convection section ; ( 2 ) increasign the heat interchanging area of radiant tubes ; ( 3 ) changing the height of the chimney ; ( 4 ) using new burner with forced air supply to increase calorific capacityu ; ( 5 ) adding air preheater between the convection section and chimney to enhence the temperature of the air entering the furnace ; ( 6 ) adopting high temperature radiant coating to improve the effect of radiant heat interchanging

    針對早期建造的煉油廠和化工廠在役管式加熱爐熱負荷和熱效率低的狀況，提出了若干技術改造措施包括，增大對流管表面積以增大對流段的熱負荷；增加輻射管的換熱面積；修正煙囪高度；換用新型燃燒器，變自然通風為強制供風，以增大燃燒器的發熱量，減小過剩空氣系數，節省燃料2 % 3 % ；在對流段和煙囪之間增設空氣預熱器以提高空氣入爐溫度；採用高溫輻射塗料增強輻射換熱效果，從而增加熱源對爐壁的輻射傳熱量和爐管的傳熱量等。
  12. Considering the weakness of the solar - power adsorbers in refrigeration / air conditioning, such as the effects of heat collecting in desorption period and heat loss in adsorption period, here, a new adsorber is proposed ? ? evacuated tube which is cooled by water. simulation calculations and experiments have been performed. with a view to the intermittent characteristics of solar - powered adsorption, a continuous cycle operation for the adsorption refrigeration cooling system with active carbon fibre ( acf ) - methanol adsorption refrigeration working pair is carried out

    本文針對目前太陽能固體吸附式製冷系統中吸附集熱床在解吸階段集熱效率不高和在吸附階段散熱效果不理想的狀況，以及針對太陽能固體吸附製冷系統循環的間歇性，本文提出了一種新型吸附集熱器:真空集熱管?水冷型吸附集熱器，以活性炭纖維?甲醇為工質對實現連續製冷循環方式，並對其進行了相關的性能實驗和數值模擬計算。
  13. This experiment include many contents, in a word, that is summer condition experiment, winter condition experiment > summer - winter transition condition experiment and winter - summer transition condition experiment, furthermore summer condition experiment still include flux changing experiment and winter condition experiment still include thermal balance experiment this article dealt with the data of the test, calculating out energy absorbing ( energy discharging ) of buried pipe in winter condition ( summer condition ), input power of heat pump x heat exchanging of piece buried pipe length x co - efficiency performance ? op ( energy efficiency rate ? er ) and average heat exchanging coefficient ; in additiont this article compares the inlet water temperature and outlet water temperature of underground the first layer and the second layer buried pipe when heat pump was running, the results are that the heat exchanging ability of the second layer buried pipe outgos the first layer buried pipe, and heat exchanging is more stable ; and still analyse earth temperature resuming in the transition season. the results are earth temperature resume fast in the first week when the heat pump runs off

    本文測試內容相當多，概括地說就是四個工況的測試，即夏季製冷工況的測試、冬季供熱工況的測試、夏?冬過渡季測試和冬?夏過渡季測試；另外在夏季工況的測試中還進行了變流量測試，在冬季工況的測試中還進行了熱平衡測試。本文對測試數據進行了處理，計算出了冬（夏）季工況埋管吸（放）熱量、熱泵空調器供熱量（製冷量） 、熱泵空調器輸入功率、埋管單位管長換熱量、供熱性能系數（製冷能效比）和平均傳熱系數等；另外，還比較了熱泵運行時地下一二層埋管進出水溫度變化情形，得出地下二層埋管換熱能力優于地下一層埋管，且換熱很穩定；並分析了過渡季地下一二層埋管溫度恢復情形，得出熱泵系統停機一周內地溫恢復特別快。
  14. Thus clean factor has good adaptability to boiler load, coal quality, excess air coefficient, working medium flow, and boiler efficiency etc. the calculated result gained by inputting the data of history database of the object boiler validates the correctness and adaptability to boiler load of clean factor model

    基於穩態傳熱的清潔因子灰污監測模型，對鍋爐負荷、燃煤品質、過量空氣系數、各類工質流量、燃煤量和鍋爐熱效率等的波動變化有很好的適應性。以北侖電廠1 #爐歷史庫中數據為輸入數據，驗證了清潔因子模型的正確性和對穩定負荷的適應性。
  15. The effects of a wide variety of parameters such as the velocity, the temperature, the inlet moisture content of the primary and the secondary airflow, the channel width on basic thermodynamic criterion, such as thermal efficiency, exergy efficiency, exergy efficiency ratio, thermodynamics consummation, exergy destruction rate, exergy destruction coefficient, are simulated numerically

    在此基礎上，通過一些基本的熱力學指標，如換熱效率、火用效率、熱力學完善度、火用損率、火用損系數等，對間接蒸發冷卻過程能量以及有用能的利用、損失情況進行了分析和研究。
  16. According to the theory of engineering thermodynamics and phase change, heat - transfer process of the special working fluid heat - pipe stove is analyzed. some hypotheses are postulated and with the help of equation of mass - conservation, energy - conservation, the dynamic concentrative parameter model is built, the change of each parameter is prescribed at any stage from starting to stopping. with the thermodynamic calculation of burnable process, the parameter of device, such as heat - transfer coefficient / thermal efficiency etc, are achieved under steady state ; based on theoretic calculation, observing the actual running circumstance of the heating stove in person, with some performance comparison between the new and the old, the high efficiency and reliability of heat - pipe stove is proved, the project which expend it in the oil - filed is feasible

    對充入該工質的熱管加熱爐，本文根據工程熱力學和相變傳熱學及相關知識，對其進行了傳熱分析，經過適當假設，運用質量守恆和能量守恆定律，建立了裝置動態集中參數模型，描述了加熱爐從開機到穩定運行這一動態過程各參數的變化情況，同時對燃燒過程也進行了熱力計算，最終得到了穩態工況下裝置的換熱系數、熱效率等熱力參數；在理論計算的基礎上，親赴現場觀察該爐的實際運行情況，通過與原有的加熱爐的各項性能進行對比，最終證明新爐的高效性和可靠性，為其在油田中推廣的可行性提供了依據。
  17. The numerical simulation result obtained by taking the dimensionless mass transfer coefficient as the input parameter of the mathematical model is consistent with the 73 groups of the experimental data and the discrepancies of the enthalpy efficiency and regenerative efficiency are mainly within 15 %

    以實驗得到的量綱一傳質系數作為數學模型的輸入條件，數值計算結果與73組實驗數據吻合很好，全熱效率和再生效率的偏差均集中在15 %以內。
  18. In this paper, finite element software ansys is used to simulate the thermal conductivity and pressureless infiltration technique is used to produce aluminum infiltrated silicon carbide composite with high volume fraction of sic. the influence of interfacial thickness and temperature on thermal conductivity and cte have been investigated and analysed

    本文採用有限元軟體ansys對鋁滲碳化硅復合材料的有效熱導率進行了數值模擬，用無壓浸滲法制備了高體積分數的鋁滲碳化硅復合材料，研究了界面層厚度和溫度等對鋁滲碳化硅復合材料的熱導率和熱膨脹系數的影響，並進行了分析。
  19. On the basis mentioned above, another mathematical model for the supercharged diesel was set up. according to this model some results of simulation calculations were given. the characteristics of operation of the diesel in wet compression : including the excess air coefficient, the cylinder temperature at the beginning of compression stroke, the maximum temperature in the cylinder, the cylinder thermal load, the specific fuel consumption, and efficiency of diesel engine were obtained

    在此基礎上，又建立了增壓柴油機濕壓縮的數學模型，對噴水后柴油機的各性能參數，諸如過量空氣系數、氣缸進氣溫度，缸內最高溫度、氣缸熱負荷、比油耗、熱效率等進行了模擬計算，為增壓柴油機進口加濕技術的研究提供了理論依據。
  20. Promote condition to prevent parching, prolong continuous working time more than one time. larger applicant scope, both thin and glutinous materials can be adapted. only o - type ring should be replaced when maintaining without heavy tools and dead angles. wash thoroughly, high efficient, far more than coil heat exchanger. heat transmit coefficient is close to plate system, producing cost is high and the floor space is large

    改善了結垢的狀況，連續生產時間延長一倍以上，適用范圍更加寬廣，稀薄狀、粘稠狀物料均能勝任，維護時只要更換o形圈，無需笨重的工具，無死角，清洗徹底，效率高，換熱效率遠大於盤管式，傳熱系數接近板式，製造成本較高，佔地面積較大。
分享友人
分享到 Line

分享到臉書