熱處理工藝 的英文怎麼說

中文拼音 [rèchǔlǐgōngyì]
熱處理工藝 英文
technology for heating processing
  • 處 : 處名詞1 （地方） place 2 （方面; 某一點） part; point 3 （機關或機關里一個部門） department; offi...
  • 理 : Ⅰ名詞1 （物質組織的條紋） texture; grain （in wood skin etc ） 2 （道理;事理） reason; logic; tru...
  • 工 : Ⅰ名詞1 （工人和工人階級） worker; workman; the working class 2 （工作; 生產勞動） work; labour 3 ...
  • 藝 : Ⅰ名詞1 （技能; 技術） skill 2 （藝術） art 3 [書面語] （準則） norm; standard; criterion4 [書面語...
  • 熱處理 : [冶金學] heat treatment; heat treating熱處理保護塗料 heat treatment protective coating; 熱處理車...
  1. Induction heated oil tempered spring wire is a kind of new technical material which has been developed since 1980s. it can be heated by means of eddy induced into itself through electromagnetic coil and this method is mainly used in surface quenching. with correct designing and reasonable current frequency, induction coil and heat treatment process selected, as well as plc controlling applied, the wire can be uniform heated along cross - sectional and longitudinal direction and can be quenched and tempered continuously

    應加熱油淬火-回火彈簧鋼絲，是二十世紀八十年代發展起來的新技術材料，在國外稱為itw induction heat oil tempered spring wire 。是通過線圈電磁感應鋼絲本身產生的渦流進行加熱，通常主要用於表面淬火。經正確設計，選擇電流頻率，合理的感應線圈及熱處理工藝，並實施plc控制，可使鋼絲整個截面及長度上得到均勻加熱，進行連續整體淬火和回火。
  2. The composite roll of high speed steel has the synthetical life of over ten times more than traditional high cr cast iron roll. now the research and production of the high speed steel for roll are very drastic. in this thesis, the microstructure, heat treatment and performance of high speed steel fe - 2 % c - 4 % v - 4 % mo - 5 % cr - x % w ( wt ) are studied systematically by using metallograph, method of lattice, xrd, sem, eds and hardness

    本文利用金相法（包括黑白金相和彩色金相） 、 x射線衍射（ xrd ） 、掃描電子顯微鏡（ sem ） 、能譜（ eds ）及洛氏硬度分析儀等手段，對復合軋輥用高速鋼fe - 2 c - 4 v - 4 mo - 5 cr - x w （其它部分如未作特殊註明均為質量分數）合金系的顯微組織、熱處理工藝及性能進行了系統地分析。
  3. Heat treatment of superalloy for aviation

    航空用高溫合金熱處理工藝
  4. Knows well about heat - treating process on steels

    非常了解鋼材的熱處理工藝。
  5. The prevention of quenching crackles in heat - treating technology

    熱處理工藝中淬火裂紋的預防
  6. Help suppliers improve manufacturing and heat - treating processes

    幫助供應商改進製造和熱處理工藝。
  7. The effect of compound casting technology and compound modification on the properties of high speed steel roll collar was studied. the results showed that compound high speed steel roll collar with high and even hardness and good bond between outer and inner layers could be gained when the modified colbalt free high speed steel in outer layer and nodular iron inner layer in connection with appropriate rotational speed of centrifugal machine, pertinent pouring interval between two kinds of the melt and moderate pouring temperature as well as surface induction heat treatment were chosen. it is indicated in industrial use that the service life of compound roll collar is higher by 5 times than that of high chromium cast iron collar

    研究了離心復合鑄造工藝和復合變質處理對高速鋼輥環性能的影響，結果表明，選用變質高碳無鈷高速鋼作外層，用球鐵作內層，選擇合適的離心機轉速、兩種金屬熔液澆注間隔時間和澆注溫度，結合採用表面感應熱處理工藝，可獲得硬度高、均勻性好、內外層結合良好的高速鋼復合輥環，用於工業生產其使用壽命比高鉻鑄鐵輥環提高5倍以上。
  8. Engaged in scientific research of metal heat treatment techniques & facilities and plant planning for 35 years. having the all - round grasp ability in planning and development of plant planning and technology reforming

    三十五年來從事金屬學熱處理工藝及設備的科研和工廠設計，對機械工廠建設和技術改造總體規劃和發展具有全局把握能力
  9. Heat treatment process of cr5mo1v cold working die steel

    冷作模具鋼熱處理工藝
  10. By vacuum - electron - beam weld of ti3al and tc11 the technology of hot die forging, and then use different heat treatments, study the influence law of the different degree of deform, different heat treatments to the microstructure and properties

    採用熱模鍛技術，通過對tac - 1b 、 tc11進行不同程度的變形、真空電子束焊接，然後採用不同的熱處理工藝，研究熱加工工藝對合金組織，性能的影響規律。
  11. Cu - zn - cr - zr conducting bar alloy and cu - cr - zr end ring alloys used for superpower asynchronous traction motor rotor were prepared by ingot metallurgy. using hardness measurement, tensile test at room and higher temperature, electrical resistance test at room and higher temperature, optical microscopy, xrd, sem, and tem, the mechanical and electric properties and the microstructure of above alloys at different treatment were studied. them were also analysed and explained in theory

    採用鑄錠冶金法制備了大功率異步牽引電動機轉子用導條合金和端環合金，通過硬度測試、室溫拉伸、高溫拉伸、電導率測定、金相分析、 xrd 、 sem 、 tem等方法研究了不同加工工藝和熱處理工藝對上述合金力學性能、導電性能及其組織結構的影響和變化規律，並從理論上進行了分析和解釋。
  12. Smelting and heat treatment technology of astm a216 wca steel casting cover

    大型鑄鋼端蓋的冶煉及熱處理工藝
  13. Based on ladle refining, wide flat anvil forge with great forging ratio, heat treatment process of " normalizing + spheroidizing + diffusion hydrogen ", the cold roll blank has been forged succesfully, and the percent of pass is up to 90. 5 %

    採用鋼包精煉爐冶煉、寬平砧大壓下量鍛造、 「正火+球化+擴氫」的熱處理工藝，成功製造了冷輥坯，合格率達90 . 5 。
  14. Abstract : based on ladle refining, wide flat anvil forge with great forging ratio, heat treatment process of & quot; normalizing + spheroidizing + diffusion hydrogen & quot;, the cold roll blank has been forged succesfully, and the percent of pass is up to 90. 5 %

    文摘:採用鋼包精煉爐冶煉、寬平砧大壓下量鍛造、 「正火+球化+擴氫」的熱處理工藝，成功製造了冷輥坯，合格率達90 . 5 。
  15. The reason for crankshaft fracture in an mwmtbd234v6 diesel was analyzed. the results show that overheating and overburning is the direct reason for fracture. the heat treatment of the crankshaft is not perfect or consistent with the standard. the lubrication is not good in service. all these accelerate the fracture

    分析mwmtbd234v6型柴油機的曲軸斷裂原因，結果表明鍛件過熱過燒是導致斷裂的直接原因；曲軸熱處理工藝不規范、不完善，曲軸工作潤滑條件不良加速了曲軸斷裂
  16. Because of its excellent properties, such as high strength, high module, wear resisting, and etc., sicp was added to ferroalloy as a reinforce phase. but the intrinsic difference between the bonds led to poor fabrication of the composites. in this paper, the effects of alloying, sintering, and heat - treatment on the properties and microstructures of sicp / ferroalloy - based composites were studied, : it was found that sic particles reacted with ferroalloy when sintered in 1100

    碳化硅因其高強度、高模量、耐熱、耐磨等優良性能而被作為顆粒增強體來制備鐵基復合材料，但因其共價鍵與鐵基體的金屬鍵之間的本質區別導致兩者復合困難，本文擬從基體合金化、燒結及熱處理工藝等方面對鐵合金基復合材料組織與性能的影響進行考察，具體內容如下：加入fe - cu - c基體中的sicp顆粒， 1100燒結時就已經開始發生分解，但反應不強烈，在顆粒表面鍍鎳可以延緩基顆粒與基體之間的反應。
  17. The influence of the quenching and tempering treatment and the different subcritical treatment on microstrcture and property of a high alloy white cast iron was studied

    摘要研究了淬回火和不同的亞臨界熱處理工藝對高合金白口鑄鐵組織和性能的影響。
  18. Cast and heat - treatment process of high strength aluminum alloy

    高強度鋁合金鑄造及熱處理工藝
  19. Heat treatment of ferrous materials ; notation to indicate heat treatment processes

    鋼鐵材料的熱處理.第3部分:熱處理工藝指示標記
  20. The foundry and heat treatment processes have been explored in order to improve properties of stainless steel. the method of solution heat treatment at high temperature with cooling controlled has been put forward

    為了全面改善cr30mo鐵素體不銹鋼的性能，充分發揮不銹鋼的微合金化作用，對于不銹鋼的熱處理工藝進行探討，提出高溫固溶處理，控製冷卻措施。
分享友人
分享到 Line

分享到臉書