燃燒面積增大 的英文怎麼說
中文拼音 [ránshāomiànjīzēngdà]
燃燒面積增大
英文
burning surface augmentation- 燃 : 動詞1. （燃燒） burn 2. （引火點著） ignite; light
- 燒 : Ⅰ動詞1 （使東西著火） burn 2 （加熱或接觸某些化學藥品、放射性物質等使物體起變化） cook; bake; hea...
- 面 : Ⅰ名詞1 （頭的前部; 臉） face 2 （物體的表面） surface; top 3 （外露的一層或正面） outside; the ri...
- 積 : Ⅰ動詞（積累） amass; store up; accumulate Ⅱ形容詞（長時間積累下來的） long standing; long pending...
- 燃燒 : （物質劇烈氧化而發光、發熱; 燒） burn; kindle; flame; set on fire; [化學] combustion; inflammation; ignition
- 面積 : [數學] area
-
Abstract : the in servie tubular heaters built early in refineries and chemical plans have low thermal load and low heat efficiency, therefore measures for technical reform are offered, including ( 1 ) enlarging the surface area of convection tubes to increase the thermal load of rhe convection section ; ( 2 ) increasign the heat interchanging area of radiant tubes ; ( 3 ) changing the height of the chimney ; ( 4 ) using new burner with forced air supply to increase calorific capacityu ; ( 5 ) adding air preheater between the convection section and chimney to enhence the temperature of the air entering the furnace ; ( 6 ) adopting high temperature radiant coating to improve the effect of radiant heat interchanging
文摘:針對早期建造的煉油廠和化工廠在役管式加熱爐熱負荷和熱效率低的狀況，提出了若干技術改造措施包括，增大對流管表面積以增大對流段的熱負荷；增加輻射管的換熱面積；修正煙囪高度；換用新型燃燒器，變自然通風為強制供風，以增大燃燒器的發熱量，減小過剩空氣系數，節省燃料2 % 3 % ；在對流段和煙囪之間增設空氣預熱器以提高空氣入爐溫度；採用高溫輻射塗料增強輻射換熱效果，從而增加熱源對爐壁的輻射傳熱量和爐管的傳熱量等。The in servie tubular heaters built early in refineries and chemical plans have low thermal load and low heat efficiency, therefore measures for technical reform are offered, including ( 1 ) enlarging the surface area of convection tubes to increase the thermal load of rhe convection section ; ( 2 ) increasign the heat interchanging area of radiant tubes ; ( 3 ) changing the height of the chimney ; ( 4 ) using new burner with forced air supply to increase calorific capacityu ; ( 5 ) adding air preheater between the convection section and chimney to enhence the temperature of the air entering the furnace ; ( 6 ) adopting high temperature radiant coating to improve the effect of radiant heat interchanging
針對早期建造的煉油廠和化工廠在役管式加熱爐熱負荷和熱效率低的狀況，提出了若干技術改造措施包括，增大對流管表面積以增大對流段的熱負荷；增加輻射管的換熱面積；修正煙囪高度；換用新型燃燒器，變自然通風為強制供風，以增大燃燒器的發熱量，減小過剩空氣系數，節省燃料2 % 3 % ；在對流段和煙囪之間增設空氣預熱器以提高空氣入爐溫度；採用高溫輻射塗料增強輻射換熱效果，從而增加熱源對爐壁的輻射傳熱量和爐管的傳熱量等。The experimental results indicates that the secondary mass flow increases with increasing of primary mass flow rate, but the bypass decrease because the primary mass flow rate increase more rapidly than secondary mass flow. the expansion configuration shows low thrust property due to low pressure in flow path. the secondary nozzle changes the pressure distribution in ejector combustor, and decreases bypass ratio, but obtain more completely mixing
結果表明：二次流流量隨著一次流流量的增加而增加，由於二次流流量的增加速度低於一次流，引射系數減小；在純擴張式結構實驗中，引射燃燒室壓強很低，難以實驗推力增強；二次噴管改變了引射燃燒室的壓強分佈，降低了引射系數，改善了混合狀況能；對于本文的實驗結構，存在一個最優的二次噴管出口面積，使引射火箭推力最大，同數值模擬結果相吻合。
分享友人