燒坯 的英文怎麼說

中文拼音 [shāopī]
燒坯 英文
sintering briquette; sintering compact; sintering shape
  • 燒 : Ⅰ動詞1 （使東西著火） burn 2 （加熱或接觸某些化學藥品、放射性物質等使物體起變化） cook; bake; hea...
  • 坯 : 名詞1 （未經燒制的磚、瓦、瓷等的製品） base 2 （土坯） unburnt brick; earthen brick; adobe 3 [方...
  1. We also attainted mosi2 / sic composite by using melting mosi2 infiltrated sic body which shaped by sic powder. the result show that the diameters of sic particle and shaping methods have effect on the composite ' s microstructure and properties

    另外，嘗試了用mosi _ 2在2050下浸滲直接由sic粉體成型的坯體制備mosi _ 2 / sic復合材料。採用sic顆粒的級配有利於提高坯體密度，但是降低燒結體的緻密度。
  2. To get the black underglaze, the bisque was first coated with white slip with ornamental lines in black paint and then sharp tools were used to outline the patterns features. sometimes a whittling technique would be employed to expose the white bisque. the piece was subsequently coated with transparent glaze and fired in the kiln, thus creating a sharp contrast between the black and the white

    釉下黑彩劃花，是先在成形的坯上抹上白化妝土，再用黑彩于化妝土上繪畫紋樣，再用利器勾劃輪廓，有些甚至加以削剔，使黑彩下的白化妝土重現，然後再施透明釉，及入燒制。
  3. The shaped briquet was sintered at 1600 for 2. 5 hours under normal pressure and at certain heating rate in si - mo electric furnace

    成型后的坯體置於硅鉬棒電爐中，在常壓、適當升溫速率下於1600保溫2 . 5小時燒結。
  4. To meet the processing requirements before sintering, the pressed briquet was pre - calcined at 1150 to make it possess adequate processing strength at first and then was shaped through precise turning on the numerical control lathe according to the design diagram of the femoral head prostheses of partial hip joint

    為滿足燒結前坯體加工的要求，壓制后的坯體在1150預燒，使其具備一定的加工強度，然後按照半髖關節股骨頭假體的形狀尺寸設計圖在數控車床上進行精密車削成型。
  5. The kilns at wun yiu finally ceased to operate in 1932. mr. au ka - fat, a local archaeologist, conducted two archaeological investigations at the wun yiu kiln site in 1995 and 1999 and discovered well - preserved remains including china clay quarrying pits, water mills, animal - driven grinder, clay - soaking tanks, paste - making workshop and dragon kilns, which illustrate the complete process of porcelain production. this is in fact a very rare archaeological discovery in the development of chinese porcelain

    一九九五和一九九九年，考古學家區家發先生在碗遺址進行了兩次考古調查，結果發現，遺址保存了生產陶瓷從采礦到入裝燒各項工序的完整遺跡，包括礦坑、礦洞、水碓作坊、碾磨作坊、淘洗池、制坯作坊和等，這在中國陶瓷考古史上是十分罕見的，是香港重要的文化遺產。
  6. Using material, which composition is basically same to substrates through grinding, and then dipping its slurry on substrate with heating 800 and then sintering at 1400. there was no crack on the surface of coating. distinguish between coating and substrate may use sem, from sem micrographs of cross section of coating, there is gradated pore structure, while pore - forming agent is no good for coating

    採用與基體成分相同的原料配製的料漿在經800燒成的素坯上成膜，燒成后發現，添加成孔劑的料漿成膜后表面易於開裂，而未加成孔劑的料漿成膜效果較好。
  7. Color - painting is of two sorts : overglaze painting and underglaze painting. overglaze painting, with five - colored painting or fencai as its example, is to outline patterns with zhuming pigment and to fill them with various colors on the already glazed surface of the porcelain, before it is placed into a closed oven for a further baking at a compar - atively low temperature from 700 to 800c. underglaze painting is to paint with qinghua, underglaze red and other pigments on the body before it is glazed. its feature is that all the colors are under the glaze formed at high temperature and thus will never fade away

    釉上彩如五彩粉彩等，是在已燒成瓷的釉面上描繪紋樣填彩，再入紅爐以低溫燒烘，溫度約700 - 800度。此外，燒窯前即在坯體素胎上繪畫，如青花釉里紅等，則稱為釉下彩，其特點是彩在高溫釉下，永不退色。
  8. Furthermore, referring to the literature and considering the specific experimental conditions given by the research, expression of the change of feed rate with time is presented, to obtain the linear growth of the diameter of pre - sintered glass beads, thus the distribution of beads size is relatively well controlled and raw material is spared in some extent. eventually, during the experiment discrete change of feed rate is implemented, and the practical changes of average diameter are plotted, then the results are compared with the theoretical calculated data

    另外，本文通過對造粒技術、燒結過程的大員文獻調研，結合本研究的具體情況，通過控制進料速率呈連續性變化，基本實現了燒結前球坯直徑的線性生長變化，從而更有利於實際生產中的產品粒度控制以及做到節約用料，並在試驗操作中以離散型進料速率變化來加以比較驗證。
  9. W - cu composites prepared from the precipitation w - cu powder have higher sintered density, better mechanical and physical property, more homogeneous and finer microstructure than those prepared from w - cu powder by the balling - reduction method. in chapter 5, a combination of homogeneous precipitation and ball - milling process, namely the mechano - thermochemical process was employed to prepare ultra - fine w - cu powder

    其中，球磨w一cu復合粉（ hp一m ）壓坯在1150下燒結30min后，可獲得相對密度大於99 %的幾乎全緻密的超細晶粒w一cu復合材料， w的顆粒度小於0 . 5林m 。
  10. Made of polytetrafluoethylene resin added with a certain volume of colouring agent shaped as blank by moulding and sintering, then through cutting and rolling to have the stereospecific and non - stereospecific coloured film in 13 kinds of colour i. e. red, green, yellow, violet, brown, black, orange, white and etc

    用聚四氟乙烯樹脂加入一定量的著色劑后經模壓，燒結製成坯料再經車削，壓延製成紅、綠、藍、黃、紫、棕、黑、橙、白等十三種顏色的聚四氟乙烯定向或不定向彩色薄膜。
  11. The expansion and dehiscence behavior during the vacuum reactive sintering below 660 of compact ti / al composite powders was experimentally investigated, and the reasons of expansion and dehiscence were theoretically analyzed. the method of low temperature reactive sintering was generalized, and the experiment testified the method effective. the rule of the expansion of the billets was generalized from the result of density of the billets

    低溫反應燒結工藝:研究了高能球磨ti / al復合粉體在溫度低於660下真空無壓反應燒結過程中的膨脹和開裂行為，分析了產生膨脹和開裂的主要原因;並提出了能夠有效預防坯料開裂的方法;通過測定坯料在低溫燒結后的密度，總結了其體積膨脹的規律;通過x射線衍射技術分析了隨球磨時間不同，金屬間化合物的生成情況。
  12. Avoiding the difficulties of detecting the difficult parameters in furnace control and of building up the models, integrated with fuzzy control and conventional pid control, abb ’ s control it system is used to predict the bloom surface and center temperature directly based on the temperature of furnace wall easily to be detected so that the temperature settings in various furnace sections can be self - corrected, the furnace temperature of each section self - adjusted and on - line parameters of combustion control self - optimized. in addition, the heating parameters and the operating status of the field plant can be monitored with alarm

    採用abb公司的controlit控制系統，避開爐子控制中遇到的困難參數檢測及建模困難等因素，直接根據容易檢測的爐壁溫度來推知鋼坯表面溫度及鋼坯中心溫度，將模糊控制技術與常規pid控制相結合，實現各段溫爐設定值自修正、各段爐溫自協調、各參數在線自整定的自尋優最佳燃燒控制;對熱工參數、現場設備的運行情況進行監視、報警，實現爐膛壓力、管道壓力、換熱器的保護控制，並將重要參數送往廠級mis網路。
  13. Pore parameters ( porosity and distribution of pore diameter ) of porous glass prepared by filler principle were measured and analyzed. they were mainly determined by the volume ratio and the particle diameter of the pore former in the green body. preparation and sintering process of the samples resulted in the difference between the porosity and the volume ratio of the pore former. they were also responsible for the deviation between the distribution of poer diameter and the particle diameter of pore former

    研究表明，利用填充法制備的多孔玻璃的孔參數（氣孔率、孔徑分佈）可進行設計與控制，多孔玻璃的氣孔率和孔徑分佈主要取決于成孔劑的體積比及其顆粒分佈，前者與後者之間的偏差取決于生坯制備及燒結過程。
  14. Theimportant technological parameters, which influence significantly thecharacterization of the screen - printed ysz electrolyte thin films, includingparticle size and particle size distribution of the starting ysz powder, composition of the screen - printing ink, sintering temperature of the screenprintedysz green films and printing times were investigated in detail

    系統研究了影響絲網印刷工藝的幾個重要參數，如ysz粉末的粒徑及粒徑分佈、印刷漿料的組成、電解質膜坯體的燒結溫度和印刷層數。
  15. Sintering behaviors of sub - micron - al2o3 green compacts at constant heating rates

    3坯體的恆速升溫燒結行為
  16. Color - painting on the porcelain ware is different from common painting. the pigment of glaze and painting on the body will undergo a great change after firing and baking at high temperature. it is in itself amazing that through kiln - firing a half - finished porcelain with dark colors and an unattractive look can be transformed into a work with so wonderful colors. from this, we can understand how exceptional the experience and imagination it requires in porcelian color - painting

    瓷器的彩繪與一般繪畫不同。因為畫工在坯體素胎上施釉和作畫時所見的顏料色，在經過高溫燒制和烘烤后會發生很大變化。看到一件件顏色暗淡貌不驚人的半成品，經過爐火的燒煉竟會呈現出如此絢麗奪目的色彩，這本身是奇妙的而與此同時也便可以得知，為瓷器作畫是需要怎樣的特殊經驗和想象力了。
  17. Metallic powders, excluding powders for hardmetals. determination of dimensional changes associated with compacting and sintering

    金屬粉末.除硬質合金外的金屬粉末.在壓坯和燒結狀態下測定尺寸變化
  18. In order to improve diamond fine powder sinter ' s mechanical property, using the present laser technique, high power transverse co2 laser is used to sinter diamond fine powder compact to study the integrating capability in the sinter between diamond fine powder and metallic powder, microstructure and the forming mechanism of microstructure in the different laser technical parameters

    摘要為了改進金剛石微粉燒結體的機械性能，利用現有的激光技術，採用高功率橫流co2激光燒結金剛石微粉壓坯，研究在不同的激光工藝參數下，燒結體中的金剛石微粉與金屬粉末粘結的結合性能、微觀結構以及形成機理。
  19. The experimental data has been used to validate pdm and low temperature sintering mechanics. the advantage and disadvantage of pdm have been discussed also. for the first time, the pdm is used to study the low temperature sintering mechanics of uo _ 2, and the research results indicate : 1

    3 、基於燒結頸長大速率與緻密化動力學方程得出，影響二氧化鈾低溫燒結的因素有原始粉末粒徑、粉末堆積方式、坯塊原始密度、燒結溫度、燒結時間、燒結氣氛等;粉末壓坯一定時，燒結溫度、燒結時間和燒結氣氛就成為控制低溫燒結的關鍵因素。
  20. In this paper, the necessary and sufficient conditions such as the diameter and some physical properties of the baked electrodes in the lengthwise graphitization furnace are highlighted and discussed in terms of single series or in multi - series packing types of the electrodes in the furnace

    摘要討論了串接石墨化爐內焙燒坯料單串裝爐和多串並聯裝爐時，坯料的直徑和一些物理性質必須滿足的充要條件。
分享友人
分享到 Line

分享到臉書